An official website of the United States government
We analyzed the surface of a freshly exfoliated single crystal of zirconium(IV) sulfide, ZrS2. Survey spectra and high-resolution spectra from the core levels Zr 4p, Zr 4s, Zr 3d, Zr 3p, Zr 3s, S 2p, S 2s, O 1s, and C 1s were acquired. The binding energies and peak area ratios of a stoichiometric ZrS2 single crystal provide a pure reference of well-defined composition for material deposited by chemical or physical vapor deposition methods.
more »
« less
This content will become publicly available on September 1, 2026
Chemical vapor deposition of zirconium(IV) sulfide on flexible polymers
The emerging optoelectronic material family of transition metal dichalcogenides may be useful in flexible electronics. However, only MoS2 has been grown directly as thin films on polymer substrates, owing in part to the high deposition temperatures typically required to prepare these materials. Changing vapor deposition chemistry can allow much lower film growth temperatures. We show that when using tetrakis(dimethylamido)zirconium(IV), Zr(NMe2)4, and H2S as precursors, low-temperature chemical vapor deposition affords films of zirconium(IV) sulfide (ZrS2) directly on polymer substrates. Stoichiometric and crystalline ZrS2 films can be deposited with good adhesion on polyimide (Kapton) and polyether ether ketone (PEEK) substrates at 150–200 °C. The films deposited on polydimethylsiloxane (PDMS) substrates were stoichiometric and crystalline, but not well adhered. Films on all substrates were polycrystalline with small (20–30 nm) grains, highly oriented in the [001] direction of the 1T ZrS2 phase. The films grown on PEEK have resistivities ca. 625 Ω cm, two orders of magnitude higher than ZrS2 films deposited at 800–1000 °C from ZrCl4 and sulfur. The films grown on Kapton are similarly conductive, whereas films on PDMS are not conductive.
more »
« less
- Award ID(s):
- 2224949
- PAR ID:
- 10615889
- Publisher / Repository:
- AIP Publishing
- Date Published:
- Journal Name:
- Journal of Vacuum Science & Technology A
- Volume:
- 43
- Issue:
- 5
- ISSN:
- 0734-2101
- Page Range / eLocation ID:
- 053402
- Subject(s) / Keyword(s):
- Semiconductor growth Polymers Thin films X-ray photoelectron spectroscopy Chemical vapor deposition Transition metal dichalcogenides Zirconium(IV) sulfide
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The transition metal dichalcogenide zirconium disulfide absorbs visible light, and its monolayers can have exceptionally large carrier mobilities. Integrating TMDC materials into wafer-based devices will likely require deposition methods operating below 400 °C. Chemical vapor deposition (CVD) may offer one such route, because it is suitable for large substrate areas and complex substrate geometries. However, current CVD methods deposit ZrS2 above 400 °C, typically from ZrCl4 and sulfur. Guided by thermochemical calculations that showed the reaction between hydrogen sulfide and tetrakis(dimethylamido)zirconium(IV) would be more favorable, we demonstrate low-temperature CVD using these compounds. Film deposition proceeds rapidly at 150–350 °C, producing stoichiometric, polycrystalline ZrS2. Films can grow at rates >100 nm/min, although slower growth increases the film crystallinity and decreases C and N impurities. At substrate temperatures above 250 °C, the film morphology transitions from densely packed small grains to larger, more loosely packed vertical sheets. In an excess of H2S, decreasing the Zr(NMe2)4 partial pressure can suppress the growth of these plates. Resistivities of product films are within 1–3 orders of magnitude of single crystal data. Optical properties are consistent with previously reported films of ZrS2, suggesting this route may offer a method for integrating ZrS2 into thermally sensitive devices.more » « less
-
Abstract The structural properties of co-deposited ultrathin PtSe 2 films grown at low temperatures by molecular beam epitaxy on c-plane Al 2 O 3 are studied. By simultaneously supplying a Se flux from a Knudsen cell and Pt atoms from an electron-beam evaporator, crystalline (001)-oriented PtSe 2 films were formed between 200 °C and 300 °C. The long separation between substrate and electron beam evaporator of about 60 cm ensured minimal thermal load. At optimum deposition temperatures, a ten times or even higher supply rate of Se compared to Pt ensured that the pronounced volatility of the Se was compensated and the PtSe 2 phase was formed and stabilized at the growth front. Postgrowth anneals under a Se flux was found to dramatically improve the crystalline quality of the films. Even before the postgrowth anneal in Se, the crystallinity of PtSe 2 films grown with the co-deposition method was superior to films realized by thermal assisted conversion. Postgrowth annealed films showed Raman modes with narrower peaks and more than twice the intensity. Transmission electron microscopy investigations revealed that the deposited material transitioned to a two-dimensional layered structure only after the postgrowth anneal. PtSe 2 growth was found to start as single layer islands that preferentially nucleated at atomic steps of the substrate and progressed in a layer-by-layer like fashion. A close to ideal wetting behavior resulted in coalesced PtSe 2 films after depositing about 1.5 PtSe 2 layers. Detailed Raman investigation of the observed PtSe 2 layer breathing modes of films grown under optimized co-deposition conditions revealed an interlayer coupling force constant of 5.0–5.6 × 10 19 N m −3 .more » « less
-
Typical titanium oxide (TiO2) films are transparent in the visible range, allowing for their index of refraction and thickness to be extracted by single-angle spectroscopic ellipsometry (SE) using a Cauchy model. However, TiO2 films grown by atomic layer deposition (ALD) from tetrakis(dimethylamino)titanium (IV) (TDMAT) and H2O at 350 °C absorb in the visible range due to the formation of Ti-O-N/Ti-N bonds. Single-angle SE is inadequate for extracting the optical constants of these films, as there are more unknowns (n, k, d) than measurable parameters (ψ, Δ). To overcome this limitation, we combined SE with transmission (T) measurements, a method known as SE + T. In the process, we developed an approach to prevent backside deposition on quartz substrates during ALD deposition. When applying a B-spline model to SE + T data, the film thicknesses on the quartz substrates closely matched those on companion Si samples measured via standard lithography. The resulting optical constants indicate a reduced refractive index, n, and increased extinction coefficient, k, when compared to purer TiO2 thin films deposited via a physical vapor deposition (PVD) method, reflecting the influence of nitrogen incorporation on the optical properties.more » « less
-
Epitaxial thick films of yttrium iron garnet (YIG) are ideal for use in microwave devices due to their low losses at high frequencies. This report is on the growth of strain-engineered YIG films by liquid-phase epitaxy (LPE) on yttrium aluminum garnet (YAG) substrates with −3% lattice mismatch with YIG. Since the use of a lattice-matched substrate is preferred for LPE growths, a seed layer of YIG, 370–400 nm in thickness, was deposited by pulsed laser deposition (PLD) on (100), (110), and (111) YAG substrates. The seed layers were stoichiometric with magnetic parameters in agreement with the parameters for bulk single-crystal YIG and with strain-induced perpendicular magnetic anisotropy field Ha = 0.19–0.43 kOe. YIG films, 4 to 8.4 μm in thickness, were grown by LPE at 870 °C on YAG substrates with the seed layers using the PbO+B2O3 flux and annealed in air at 1000 °C. The films were Y-rich and Fe-deficient and confirmed to be epitaxial single crystals by X-ray diffraction. The saturation magnetization 4πMs at room temperature was rather high and ranged from 1.9 kG to 2.3 kG. Ferromagnetic resonance at 5–15 GHz showed the absence of significant magneto-crystalline anisotropy in the LPE films with the line-width ΔH in the range 85–160 Oe, and Ha = 0.27–0.80 kOe which is much higher than for the seed layers. The high magnetization and Ha-values for the LPE films could be partially attributed to the off-stoichiometry. Although the strain due to the film–substrate lattice mismatch contributes to Ha, the mismatch in the thermal expansion coefficients for YIG and YAG is also a likely cause of Ha due to the high growth and annealing temperatures. The LPE-grown YIG films with high strain-induced anisotropy fields have the potential for use in self-biased microwave devices.more » « less
