skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Molecular beam epitaxy of PtSe 2 using a co-deposition approach
Abstract The structural properties of co-deposited ultrathin PtSe 2 films grown at low temperatures by molecular beam epitaxy on c-plane Al 2 O 3 are studied. By simultaneously supplying a Se flux from a Knudsen cell and Pt atoms from an electron-beam evaporator, crystalline (001)-oriented PtSe 2 films were formed between 200 °C and 300 °C. The long separation between substrate and electron beam evaporator of about 60 cm ensured minimal thermal load. At optimum deposition temperatures, a ten times or even higher supply rate of Se compared to Pt ensured that the pronounced volatility of the Se was compensated and the PtSe 2 phase was formed and stabilized at the growth front. Postgrowth anneals under a Se flux was found to dramatically improve the crystalline quality of the films. Even before the postgrowth anneal in Se, the crystallinity of PtSe 2 films grown with the co-deposition method was superior to films realized by thermal assisted conversion. Postgrowth annealed films showed Raman modes with narrower peaks and more than twice the intensity. Transmission electron microscopy investigations revealed that the deposited material transitioned to a two-dimensional layered structure only after the postgrowth anneal. PtSe 2 growth was found to start as single layer islands that preferentially nucleated at atomic steps of the substrate and progressed in a layer-by-layer like fashion. A close to ideal wetting behavior resulted in coalesced PtSe 2 films after depositing about 1.5 PtSe 2 layers. Detailed Raman investigation of the observed PtSe 2 layer breathing modes of films grown under optimized co-deposition conditions revealed an interlayer coupling force constant of 5.0–5.6 × 10 19 N m −3 .  more » « less
Award ID(s):
2039351 1539916
PAR ID:
10412531
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
2D Materials
Volume:
9
Issue:
2
ISSN:
2053-1583
Page Range / eLocation ID:
025029
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; (, Beilstein Journal of Nanotechnology)
    null (Ed.)
    Two platinum precursors, Pt(CO) 2 Cl 2 and Pt(CO) 2 Br 2 , were designed for focused electron beam-induced deposition (FEBID) with the aim of producing platinum deposits of higher purity than those deposited from commercially available precursors. In this work, we present the first deposition experiments in a scanning electron microscope (SEM), wherein series of pillars were successfully grown from both precursors. The growth of the pillars was studied as a function of the electron dose and compared to deposits grown from the commercially available precursor MeCpPtMe 3 . The composition of the deposits was determined using energy-dispersive X-ray spectroscopy (EDX) and compared to the composition of deposits from MeCpPtMe 3 , as well as deposits made in an ultrahigh-vacuum (UHV) environment. A slight increase in metal content and a higher growth rate are achieved in the SEM for deposits from Pt(CO) 2 Cl 2 compared to MeCpPtMe 3 . However, deposits made from Pt(CO) 2 Br 2 show slightly less metal content and a lower growth rate compared to MeCpPtMe 3 . With both Pt(CO) 2 Cl 2 and Pt(CO) 2 Br 2 , a marked difference in composition was found between deposits made in the SEM and deposits made in UHV. In addition to Pt, the UHV deposits contained halogen species and little or no carbon, while the SEM deposits contained only small amounts of halogen species but high carbon content. Results from this study highlight the effect that deposition conditions can have on the composition of deposits created by FEBID. 
    more » « less
  2. ; ; ; ; ; (, Nanotechnology)
    Abstract This work evaluates the passivation efficacy of thermal atomic layer deposited (ALD) Al 2 O 3 dielectric layer on self-catalyzed GaAs 1- x Sb x nanowires (NWs) grown using molecular beam epitaxy. A detailed assessment of surface chemical composition and optical properties of Al 2 O 3 passivated NWs with and without prior sulfur treatment were studied and compared to as-grown samples using x-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and low-temperature photoluminescence (PL) spectroscopy. The XPS measurements reveal that prior sulfur treatment followed by Al 2 O 3 ALD deposition abates III–V native oxides from the NW surface. However, the degradation in 4K-PL intensity by an order of magnitude observed for NWs with Al 2 O 3 shell layer compared to the as-grown NWs, irrespective of prior sulfur treatment, suggests the formation of defect states at the NW/dielectric interface contributing to non-radiative recombination centers. This is corroborated by the Raman spectral broadening of LO and TO Raman modes, increased background scattering, and redshift observed for Al 2 O 3 deposited NWs relative to the as-grown. Thus, our work seems to indicate the unsuitability of ALD deposited Al 2 O 3 as a passivation layer for GaAsSb NWs. 
    more » « less
  3. ; ; ; (, Journal of Vacuum Science & Technology A)
    The emerging optoelectronic material family of transition metal dichalcogenides may be useful in flexible electronics. However, only MoS2 has been grown directly as thin films on polymer substrates, owing in part to the high deposition temperatures typically required to prepare these materials. Changing vapor deposition chemistry can allow much lower film growth temperatures. We show that when using tetrakis(dimethylamido)zirconium(IV), Zr(NMe2)4, and H2S as precursors, low-temperature chemical vapor deposition affords films of zirconium(IV) sulfide (ZrS2) directly on polymer substrates. Stoichiometric and crystalline ZrS2 films can be deposited with good adhesion on polyimide (Kapton) and polyether ether ketone (PEEK) substrates at 150–200 °C. The films deposited on polydimethylsiloxane (PDMS) substrates were stoichiometric and crystalline, but not well adhered. Films on all substrates were polycrystalline with small (20–30 nm) grains, highly oriented in the [001] direction of the 1T ZrS2 phase. The films grown on PEEK have resistivities ca. 625 Ω cm, two orders of magnitude higher than ZrS2 films deposited at 800–1000 °C from ZrCl4 and sulfur. The films grown on Kapton are similarly conductive, whereas films on PDMS are not conductive. 
    more » « less
  4. (, Proceedings Volume 11281, Oxide-based Materials and Devices XI)
    Transparent conducting oxides, such as Ga-doped ZnO (GZO) and Al-doped ZnO (AZO) are attractive materials for high-performance plasmonic devices operating at telecommunication wavelengths. In this contribution, we compare the growth of epsilon-near-zero GZO and AZO films on sapphire by two different deposition techniques: molecular beam epitaxy (MBE) and atomic layer deposition (ALD). For MBE of GZO, a multiple buffer consisted of a high-temperature MgO layer, a low-temperature ZnO, followed by a high-temperature ZnO layer is employed to assure the crystalline quality of the GZO film. By controlling the growth parameters, including Ga doping level, VI/II ratio, substrate temperature, we are able to produce GZO films at 350 °C with electron mobility between 30 and 50 cm2/V.s, electron concentration up to 7×1020 cm-3, and resistivity down to 2.5×10-4 Ω.cm. For ALD of AZO, without using any buffer, by reducing the Al pulse duration, we are able to grow the AZO films under a large ratio of Al to Zn pulses of 1:6, which improves the activation of Al as an effective dopant. Hence AZO films with electron concentration above 7×1020 cm-3, electron mobility between 10 and 20 cm2/V.s, and resistivity below 6×10-4 Ω.cm have been obtained at 250 °C. The corresponding epsilon-near-zero point in the ALD-grown material was tuned down to 1470 nm. Our data indicate that the ALD method provides a low-temperature route to plasmonic TCOs for telecommunication wavelength range. Effect of electron mobility on optical loss and, therefore, plasmonic figure of merit is discussed. 
    more » « less
  5. ; ; ; (, Nanomaterials)
    The electrical properties of graphene on dielectric substrates, such as silicon carbide (SiC), have received much attention due to their interesting applications. This work presents a method to grow graphene on a 6H-SiC substrate at a pressure of 35 Torr by using the hot filament chemical vapor deposition (HFCVD) technique. The graphene deposition was conducted in an atmosphere of methane and hydrogen at a temperature of 950 °C. The graphene films were analyzed using Raman spectroscopy, scanning electron microscopy, atomic force microscopy, energy dispersive X-ray, and X-ray photoelectron spectroscopy. Raman mapping and AFM measurements indicated that few-layer and multilayer graphene were deposited from the external carbon source depending on the growth parameter conditions. The compositional analysis confirmed the presence of graphene deposition on SiC substrates and the absence of any metal involved in the growth process. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email