An official website of the United States government
Abstract Strain sensors are the primary, direct sensing element in many sensors with applications in robotics, wearable sensors, structural health monitoring, and beyond. Cutting edge applications are increasing demand for sensors that can survive and measure large strains (> 5%). Presently, the most common strain sensors are composed of a serpentine metal foil which can survive strains up to about 5% with a gauge factor (GF) of about 2 (measured as change in resistance divided by initial resistance all over strain). Research into nanoparticle-based strain sensors commonly reports surviving strains up to 50% and gauge factors around 200. Unfortunately, most nanoparticle-based strain sensors are composed of expensive, toxic materials and require high precision synthesis methods. The reduced Graphene Oxide (rGO) based sensors can be synthesized easily with common materials and methods. Study of strain sensing capabilities have revealed that rGO strain sensors can survive strains beyond 15% with gauge factors (sensitivity) on the order of 200. Suspensions of graphene oxide (GO)’s flakes were deposited on flexible Polydimethylsiloxane (PDMS) substrates to create specimens with different area densities of 0.69, 0.80 and 091 mg/cm2 of GO. Specimens were thermally reduced to create rGO-based strain sensors. Resulting sensors were tested under tension applied at a rate of 0.1 mm/sec starting from 0% strain until failure. Resistance of the sensors in the direction aligned with the direction of the applied tension were measured at each 1 mm-increment of tension. Sensitivity and the strain to failure of the sensor were calculated and compared in specimens with different GO area densities. Our study suggests that with increasing the area density of graphene oxide (GO) during the synthesis of rGO, the survivability of the rGO subjected to large strains can be improved while still demonstrating a high sensitivity. This study can help tailor rGO-based strain sensors especially to the applications where high strain survival (> 30%) is required while benefiting from a reasonably good GF (> 30).
more »
« less
Sensing with Thermally Reduced Graphene Oxide under Repeated Large Multi-Directional Strain
This paper presents a recent investigation into the electromechanical behavior of thermally reduced graphene oxide (rGO) as a strain sensor undergoing repeated large mechanical strains up to 20.72%, with electrical signal output measurement in multiple directions relative to the applied strain. Strain is one the most basic and most common stimuli sensed. rGO can be synthesized from abundant materials, can survive exposure to large strains (up to 20.72%), can be synthesized directly on structures with relative ease, and provides high sensitivity, with gauge factors up to 200 regularly reported. In this investigation, a suspension of graphene oxide flakes was deposited onto Polydimethylsiloxane (PDMS) substrates and thermally reduced to create macroscopic rGO-strain sensors. Electrical resistance parallel to the direction of applied tension (x^) demonstrated linear behavior (similar to the piezoresistive behavior of solid materials under strain) up to strains around 7.5%, beyond which nonlinear resistive behavior (similar to percolative electrical behavior) was observed. Cyclic tensile testing results suggested that some residual micro-cracks remained in place after relaxation from the first cycle of tensile loading. A linear fit across the range of strains investigated produced a gauge factor of 91.50(Ω/Ω)/(m/m), though it was observed that the behavior at high strains was clearly nonlinear. Hysteresis testing showed high consistency in the electromechanical response of the sensor between loading and unloading within cycles as well as increased consistency in the pattern of the response between different cycles starting from cycle 2.
more »
« less
- Award ID(s):
- 2113857
- PAR ID:
- 10618448
- Publisher / Repository:
- MDPI
- Date Published:
- Journal Name:
- Sensors
- Volume:
- 24
- Issue:
- 17
- ISSN:
- 1424-8220
- Page Range / eLocation ID:
- 5739
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
We report a textile-infused sensor array, utilizing reduced graphene oxide (rGO) as a uniquely conformal negative temperature coefficient (NTC) material, for spatiotemporal mapping of skin temperatures. Nylon filaments were coated with rGO and stitched along with Ag conductive threads into a polyester fabric to create the array of individually addressable 6 × 6 NTC sensing elements. The temperature-mapping attribute of the sensor array was evaluated in comparison to infrared imaging. The rGO film remained mechanically and electrically stable upon stretching (<4% strain) and bending (<34°) of the filaments, demonstrating its conformal nature. These results suggest the intriguing possibility of thermally mapping topographically complex skin surfaces in a non-invasive, wearable, and cost effective manner.more » « less
-
This study aimed to explore lignin as a naturally occurring aromatic precursor for the synthesis of LIG and further fabrication of ultrasensitive strain sensors for the detection of small deformations. One-step direct laser writing (DLW) induced high quality porous graphene, so called laser induced graphene (LIG), from kraft lignin under the conditions optimized for laser power, focus distance, and lignin loading. An electrode based on the resulting LIG was facilely fabricated by transferring LIG onto an elastomeric substrate ( i.e. , Dragon Skin™). The novel LIG transfer was facilitated by spin coating followed by water lifting, leading to the full retention of porous graphene onto the elastomeric substrate. The strain sensor was shown to be highly sensitive to small human body motions and tiny deformations caused by vibrations. It had a working range of up to 14% strain with a gauge factor of 960 and showed high stability as evidenced by repetitive signals over 10 000 cycles at 4% strain. The sensor was also successfully demonstrated for detecting human speaking, breath, seismocardiography (SCG), and movement of pulse and eye. Overall, the lignin-derived LIG can serve as excellent piezoresistive materials for wearable, stretchable, and ultrasensitive strain sensors with applications in human body motion monitoring and sound-related applications.more » « less
-
Graphene nanocomposites are a promising class of advanced materials for sensing applications; yet, their commercialization is hindered due to impurity incorporation during fabrication and high costs. The aim of this work is to prepare graphene–polysulfone (G−PSU) and graphene–polyvinylidene fluoride (G−PVDF) nanocomposites that perform as multifunctional sensors and are formed using a one-step, in situ exfoliation process whereby graphite is exfoliated into graphene nanoflakes (GNFs) directly within the polymer. This low-cost method creates a nanocomposite while avoiding impurity exposure since the raw materials used in the in situ shear exfoliation process are graphite and polymers. The morphology, structure, thermal properties, and flexural properties were determined for G−PSU and G−PVDF nanocomposites, as well as the electromechanical sensor capability during cyclic flexural loading, temperature sensor testing while heating and cooling, and electrochemical sensor capability to detect dopamine while sensing data wirelessly. G−PSU and G−PVDF nanocomposites show superior mechanical characteristics (gauge factor around 27 and significantly enhanced modulus), thermal characteristics (stability up to 500 °C and 170 °C for G−PSU and G−PVDF, respectively), electrical characteristics (0.1 S/m and 1 S/m conductivity for G−PSU and G−PVDF, respectively), and distinguished resonant peaks for wireless sensing (~212 MHz and ~429 MHz). These uniquely formed G−PMC nanocomposites are promising candidates as strain sensors for structural health monitoring, as temperature sensors for use in automobiles and aerospace applications, and as electrochemical sensors for health care and disease diagnostics.more » « less
-
Abstract Breath ammonia is an essential biomarker for patients with many chronic illnesses, such as chronic kidney disease (CKD), chronic liver disease (CLD), urea cycle disorders (UCD), and hepatic encephalopathy. However, existing breath ammonia sensors fail to compensate for the impact of breath humidity and complex breathing motions associated with a human breath sample. Here, a multimodal breath sensing system is presented that integrates an ammonia sensor based on a thermally cleaved conjugated polymer, a humidity sensor based on reduced graphene oxide (rGO), and a breath dynamics sensor based on a 3D folded strain‐responsive mesostructure. The miniaturized construction and module‐based configuration offer flexible integration with a broad range of masks. Experimental results present the capabilities of the system in continuously detecting diagnostic ranges of breath ammonia under real, humid breath conditions with sufficient sensing accuracy and selectivity over 3 weeks. A machine‐learning algorithm based on K‐means clustering decodes multimodal signals collected from the breath sensor to differentiate between healthy and diseased breath concentrations of ammonia. The on‐body test highlights the operational simplicity and practicality of the system for noninvasively tracing ammonia biomarkers.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/s24175739
