An official website of the United States government
Al-Mg alloy disks were produced from Mg sandwiched between Al through 100 turns of high-pressure torsion (HPT) at 6.0 GPa at room temperature, resulting in high microhardness of Hv 300–350 in regions experiencing a nominal shear strain > ~ 390. While compositional mapping using scanning electron microscopy energy-dispersive spectroscopy (EDS) showed a uniform distribution of Mg through the disk thickness at 1.5 mm and 3.0 mm from the disk center, transmission electron microscopy EDS showed a heterogeneous distribution of Mg remained on the nanoscale. Although HPT induces enough mixing to result in face-center-cubic Al with supersaturations of Mg of up to ~ 20 at.% near the disk surfaces, β-Al3Mg2, γ-Al12Mg17 and Al2Mg intermetallic phases were identified by electron diffraction throughout the disk thickness even in regions experiencing high shear strain. This study visually captures detailed compositional heterogeneity throughout the sample thickness following intense mechanical alloying, nanoscale re-structuring and phase transformations.
more »
« less
This content will become publicly available on August 29, 2026
Multi-Scale Microstructural Characterization of Aluminum Alloys Subject to Advanced Processing Techniques for Improving Mechanical Properties
This work presents a multi-scale microstructural characterization of aluminum alloys processed by high-pressure torsion (HPT) and cold angular rolling process (CARP) to improve their mechanical properties. Mechanical properties such as microhardness and tensile strength were correlated with microstructural features. To understand the processing-structure-property relationships, characterization methods spanning nano- to millimeter scales were used, including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and scanning transmission electron microscopy (STEM) EDS. TEM and STEM EDS were used to show that HPT of a Mg sheet sandwiched between Al sheets successfully produced a supersaturated solid solution (SSSS) of Mg in Al and several Al-Mg intermetallic phases, leading to significant grain refinement and increases in microhardness over pure Al. Although CARP has potential to induce the severe plastic deformation (SPD), the CARP system used in this work was not able to achieve SPD aluminum alloys. However, SEM EBSD characterization shows that CARP achieves an increase of the low-angle grain boundaries (LAGBs) and geometrically necessary dislocation (GND) density in Al-1043,which improves the mechanical properties. Moreover, a preliminary study was conducted on CAPR processed Al-6061 alloys to understand the synergistic effects precipitation and CARP-processing on the microstructure and properties. This research provides the critical insights into the capabilities and current limitations of CARP as a continuous SPD technique for aluminum alloys, and demonstrate the importance of integrated multi-scale characterization in understanding advanced materials processing.
more »
« less
- Award ID(s):
- 2051205
- PAR ID:
- 10643564
- Publisher / Repository:
- Oregon State University
- Date Published:
- Format(s):
- Medium: X
- Institution:
- Oregon State University
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
There has been a great interest in evaluating the potential of severe plastic deformation (SPD) to improve the performance of magnesium for biological applications. However, different properties and trends, including some contradictions, have been reported. The present study critically reviews the structural features, mechanical properties, corrosion behavior and biological response of magnesium and its alloys processed by SPD, with an emphasis on equal-channel angular pressing (ECAP) and high-pressure torsion (HPT). The unique mechanism of grain refinement in magnesium processed via ECAP causes a large scatter in the final structure, and these microstructural differences can affect the properties and produce difficulties in establishing trends. However, the recent advances in ECAP processing and the increased availability of data from samples produced via HPT clarify that grain refinement can indeed improve the mechanical properties and corrosion resistance without compromising the biological response. It is shown that processing via SPD has great potential for improving the performance of magnesium for biological applications.more » « less
-
Severe plastic deformation (SPD) has been known for decades to provide microstructural refinement under a hydrostatic stress state by introducing a tremendous quantity of lattice defects, including vacancies, dislocations, and grain boundaries, leading to enhanced mechanical properties. Many SPD processes have been well studied and utilized for the processing of ultrafine-grained (UFG) metals and materials. One major challenge with SPD-processed UFG materials is their limited applicability, primarily due to their microstructural stability at elevated temperatures and the difficulty of scaling up to larger sizes or volumes. To first understand the thermal stability of UFG material, a copper prepared by high-pressure torsion, a technique that can achieve true nano-scale grains in bulk samples, was evaluated using two novel in situ techniques of micro-beam high-energy synchrotron X-ray diffraction. These are, namely, monochromatic X-ray beams that yield changes in microstructure with time and temperature, and a polychromatic X-ray beam that determines grain reorientation behavior during microstructural relaxation. Furthermore, a new processing technique named cold angular rolling process (CARP) demonstrated some promise as an SPD technique for producing theoretically unlimited lengths of strength-enhanced copper sheets at room temperature with a relatively low energy consumption. Additional miniature tensile testing incorporating digital image correlation (DIC) method and microstructural analysis utilizing high-energy X-ray diffraction determined the influence of CARP having higher shear strain hardening in comparison with other established techniques. This study highlights the significance of lattice-defect influenced mechanical properties and microstructure of UFG obtained across multi-length scales and volumes, which are critical for guiding the control and scalable production of advanced materials for commercialization.more » « less
-
Ultrafine-grained and heterostructured materials are currently of high interest due to their superior mechanical and functional properties. Severe plastic deformation (SPD) is one of the most effective methods to produce such materials with unique microstructure-property relationships. In this review paper, after summarizing the recent progress in developing various SPD methods for processing bulk, surface and powder of materials, the main structural and microstructural features of SPD-processed materials are explained including lattice defects, grain boundaries and phase transformations. The properties and potential applications of SPD-processed materials are then reviewed in detail including tensile properties, creep, superplasticity, hydrogen embrittlement resistance, electrical conductivity, magnetic properties, optical properties, solar energy harvesting, photocatalysis, electrocatalysis, hydrolysis, hydrogen storage, hydrogen production, CO2 conversion, corrosion resistance and biocompatibility. It is shown that achieving such properties is not currently limited to pure metals and conventional metallic alloys, and a wide range of materials are processed by SPD, including high-entropy alloys, glasses, semiconductors, ceramics and polymers. It is particularly emphasized that SPD has moved from a simple metal processing tool to a powerful means for the discovery and synthesis of new superfunctional metallic and nonmetallic materials. The article ends by declaring that the borders of SPD have been extended from materials science and it has become an interdisciplinary tool to address scientific questions such as the mechanism of geological and astronomical phenomena and the origin of life. Keywords: Severe plastic deformation (SPD); Nanostructured materials; Ultrafine grained (UFG) materials; Gradient-structured materials, High-pressure torsion (HPT)more » « less
-
Magnesium (Mg) alloys are promising lightweight structural materials whose limited strength and room‐temperature ductility limit applications. Precise control of deformation‐induced twinning through microstructural alloy design is being investigated to overcome these deficiencies. Motivated by the need to understand and control twin formation during deformation in Mg alloys, a series of magnesium‐yttrium (Mg–Y) alloys are investigated using electron backscatter diffraction (EBSD). Analysis of EBSD maps produces a large dataset of microstructural information for >40000 grains. To quantitatively determine how processing parameters and microstructural features are correlated with twin formation, interpretable machine learning (ML) is employed to statistically analyze the individual effects of microstructural features on twinning. An ML classifier is trained to predict the likelihood of twin formation, given inputs including grain microstructural information and synthesis and deformation conditions. Then, feature selection is used to score the relative importance of these inputs for twinning in Mg–Y alloys. It is determined that using information only about grain size, grain orientation, and total applied strain, the ML model can predict the presence of twinning and that other parameters do not significantly contribute to increasing the model's predictive accuracy. Herein, the utility of ML for gaining new fundamental insights into materials processing is illustrated.more » « less
