An official website of the United States government
Emerging power electronic drives and converters are planned to operate at high voltages with high switching frequencies (up to a few hundred kHz), which will affect the reliability of insulation systems of windings of electrical machines. To evaluate the insulation quality under such high-frequency pulses, lifetime test is a prominent way. For simplification of test procedure, turn-to-turn insulation samples are approved by IEC 60034-18-42. In past studies, the impact of switching frequencies has been investigated under lower frequencies (up to 20 kHz), which cannot address the challenges of next-generation wide bandgap (WBG)-based power converters. In this study, the lifetimes of turn-to-turn insulations under high switching frequencies (50 kHz) are tested at four different rise times (50 ns, 100 ns, 150 ns, 200 ns), and the impact of switching frequency on the lifetime of the insulation is analyzed.
more »
« less
This content will become publicly available on April 11, 2026
Impact of Rise Time and Frequency on Motor Winding Insulation Lifetime Under High Frequency, High Slew Rate Bipolar Square Wave Voltages
Emerging power electronic drives and converters, especially wide bandgap (WBG) technology-based devices, are expected to operate at high voltages and switching frequencies, potentially reaching up to several hundred kHz. These operating conditions pose significant challenges to the reliability of insulation systems in motor windings, which are critical to the longevity and safe operation of electrical machines. This study investigates the impact of high-frequency square wave voltage pulses on the lifetime of motor winding insulation by conducting lifetime tests on twisted pair magnet wire commonly used in electrical machines. The experiments were conducted in the frequency range of 100 kHz to 300 kHz, with rise times of 50 ns and 400 ns (slew rate ranging from 2.4kV/μ s to 19.2kV/μs), to simulate the conditions typical in modern power electronics and inverter-driven systems. The results show that fast rise times and high switching frequencies influence turn-to-turn insulation's aging and breakdown characteristics. The findings highlight the importance of switching frequency and rise time in determining the reliability of insulation systems, offering critical data to enhance the design and performance of electrical machines in the context of high-frequency operation.
more »
« less
- Award ID(s):
- 2306093
- PAR ID:
- 10652891
- Publisher / Repository:
- IEEE
- Date Published:
- Page Range / eLocation ID:
- 1 to 6
- Format(s):
- Medium: X
- Location:
- Arlington, TX, USA
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This study examines how fast rise times, which are common in modern power electronics and drive systems, affect the aging of electric machine windings. It focuses on how to ensure these windings can last longer and work reliably in electrical systems. A twisted pair magnet wire with insulation commonly used in wound machines was used to get experimental data to understand how different voltage waveforms can influence endurance testing of motor insulation systems powered by inverters. Unlike past studies that looked at comparatively slower rise times and fewer repetitions, this research specifically addresses the challenges posed by next-generation wide bandgap (WBG)-based conversion systems. These systems operate at very high speeds, up to 100 kV/μs, and switch frequencies up to 500 kHz, where both frequency and rise time are crucial factors affecting insulation aging over time.more » « less
-
Air has always been an insulation medium that mainly interfaces with solid dielectrics within power electronics building blocks (PEBBs). Equipped with wide-bandgap (WBG) and ultrawide-bandgap (UWBG) devices, air around sharp edges is stressed by high frequency, high slew rate square wave voltage pulses within PEBBs. Having a lower insulation strength than solid dielectrics, decreased dielectric strength of air due to high frequencies and high slew rates of applied voltage can lead to enhanced surface discharges at interfaces, leading to degradation of solid dielectrics and eventually their breakdown. This shows the importance of studying the rise time and frequency effect on air breakdown subjected to the square wave voltage pulses at normal pressure, which is the main objective of our research. This study focuses on understanding the air breakdown voltage behavior under a frequency range of 2.5 kHz to 75 kHz and a rise time between 50 ns and 150 ns. This study reveals that a higher breakdown voltage (BDV) occurs at longer rise times, consistent with previous research, except for 150 ns, in which the expected effect was not observed. Results showed that BDV decreases with frequency increases beyond 20 kHz. For 75 kHz and a rise time of 125 ns, BDV reduces by 30 % to that of 10 kHz.more » « less
-
Wide bandgap (WBG) and ultra-wide bandgap (UWBG)-based inverters are increasingly being adopted in More Electric Aircraft (MEA) and All Electric Aircraft (AEA) due to their ability to operate at higher switching frequencies with improved efficiency and power density. However, these advantages come with drawbacks, including increased electrical stress and exacerbation of AC losses, such as the skin effect and proximity effect. Litz wire, known for its effectiveness in mitigating these losses, is becoming a preferred conductor in highvoltage, high-frequency aerospace applications. This study investigates the breakdown voltage behavior of Litz wire insulation under square wave voltage stress across different frequencies. Twisted-pair Litz wire specimens were tested using a state-of-the-art high-voltage pulse generator with fixed rise times to emulate inverter-fed conditions. The resulting breakdown voltages were statistically analyzed using the Weibull distribution to evaluate insulation strength and failure predictability. The findings offer new insights into the insulation characteristics of Litz wire under realistic high-frequency converter stress and support the development of converter-resistant insulation systems for next-generation aerospace electrical power systems (EPS).more » « less
-
Electric vehicles (EVs) rely on robust inverter-to-motor connections to ensure high-efficiency operation under the challenging conditions imposed by wide-bandgap (WBG) semiconductors. High switching frequencies and steep voltage rise times in WBG inverters lead to repetitive transient overvoltages, causing insulation degradation and premature motor winding failure. This study proposes a wideband (WB) model of EV cables, developed in EMTP-RV, to improve transient voltage prediction accuracy compared to the traditional constant parameter (CP) model. Using a commercially available EV-dedicated cable, the WB model incorporates frequency-dependent parasitic effects calculated through the vector fitting technique. The motor design is supported by COMSOL Multiphysics and MATLAB 2023 simulations, leveraging the multi-conductor transmission line (MCTL) model for validation. Using practical data from the Toyota Prius 2010 model, including cable length, motor specifications, and power ratings, transient overvoltages generated by high-frequency inverters are studied. The proposed model demonstrates improved alignment with real-world scenarios, providing valuable insights into optimizing insulation systems for EV applications.more » « less
