An official website of the United States government
Abstract Krauklis waves are generated by pressure disturbances in fluid‐filled cavities and travel along the solid‐fluid interface. Their far‐field radiation, observed in seismic data from volcanoes or hydraulic fracturing, is known as long‐period events. Characterized by low velocity and resonance, Krauklis waves help estimate fracture size and discern fluids in saturated fractures. Despite numerous theoretical models analyzing Krauklis waves, the existing paradigms are founded on static flow conditions. However, in geological contexts, the assumption of static flow may not be valid. We developed an experimental apparatus using a tri‐layer model consisting of a pair of aluminum plates to examine the effect of fluid flow on Krauklis waves. We employed an infusion syringe pump to inject fluids into the fracture under different flow rates. We used water, oil, and an aqueous solution of Polyethylene glycol as fracture fluids. We calculated resonant frequency, phase velocity, and quality factor to characterize the Krauklis waves. Our findings reveal that an increase in flow rate leads to a higher phase velocity, higher quality factor, and a shift to higher resonant frequency when the flow is in the direction of initial wave propagation while decreasing amplitude. Additionally, when the flow is in the opposite direction of initial wave propagation, we note higher wave absorption and distortion of the Krauklis waves. Our observations unequivocally affirm that fluid flow leaves strong signatures on the Krauklis waves, providing a robust basis for characterizing fluid dynamics within geological settings through the analysis of Krauklis wave.
more »
« less
A controlled-source physical model for long period seismic events
SUMMARY Long-period seismic events (LPs) are observed within active volcanoes, hydrothermal systems and hydraulic fracturing. The prevailing model for LP seismic events suggests that they result from pressure disturbances in fluid-filled cracks that generate slow, dispersive waves known as Krauklis waves. These waves oscillate within the crack, causing it to act as a seismic resonator whose far-field radiations are known as LP events. Since these events are generated from fluid-filled cracks, they have been used to analyse fluid transport and fracturing in geological settings. Additionally, they are deemed precursors to volcanic eruptions. However, other mechanisms have been proposed to explain LP seismicity. Thus, a robust interpretation of these events requires understanding all parameters contributing to LP seismicity. To achieve this, for the first time, we have developed a physical model to investigate LP seismicity under controlled-source conditions. The physical model consists of a 30 cm × 15 cm × 0.2 cm crack embedded within a concrete slab with dimensions of 3 m × 3 m × 0.24 m. Using this apparatus, we investigate fundamental factors affecting long-period seismic signals, including crack stiffness, fluid density and viscosity, radiation patterns and triggering location. Our findings are consistent with the theoretical model for Krauklis waves within a fluid-filled crack. In this study, we examine the interplay between fluid properties and characteristics of waves within and radiated from the crack model. Records from a pressure transducer within the crack model have the same frequency characteristics as the surface sensors, indicating that the surface sensors are recording the crack waves. Because the crack stiffness parameters for all the fluids are relatively high, fluid density variations have a larger effect on the crack wave frequency, with higher density fluids yielding lower resonance frequencies. Similarly, the quality factor (Q) decreases with increasing fluid density. We also find that an increase in fluid viscosity along with the increased fluid density results in a decrease in resonance frequency and Q. Trigger locations at the middle of the crack length and width most effectively resonated the first and second transverse modes. Thus, this physical model can offer new horizons in understanding LP seismicity and bridge the gap between theoretical models and observed LP signals.
more »
« less
- Award ID(s):
- 2021768
- PAR ID:
- 10658194
- Publisher / Repository:
- Oxford University Press
- Date Published:
- Journal Name:
- Geophysical Journal International
- Volume:
- 241
- Issue:
- 3
- ISSN:
- 0956-540X
- Page Range / eLocation ID:
- 1947 to 1961
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
ABSTRACT:The mechanism of formation of natural cracks in sedimentary rocks in the geologic past is an important problem in hydraulic fracturing. Why are the natural cracks roughly parallel and equidistant, and why is the spacing in the order of 10 cm rather than 1 cm or 100 cm? Fracture mechanics alone cannot answer these questions. Here it is proposed that fracture mechanics must be coupled with the diffusion of solute ions (Na+ and Cl− are considered here), driven by an osmotic pressure gradient. Parallel equidistant cracks are considered to be subcritical and governed by the Charles-Evans law. The evolution in solute concentration also affects the solvent pressure in the pores and cracks, altering the resistance to frictional sliding. Only steady-state propagation and periodic cracks are studied. An analytical solution of the crack spacing as a function of the properties of the rock as well as the solvent and solute, and the imposed far-field deformation is obtained. Finally, the stability of the growth of parallel cracks is proven by examining the second variation of free energy. Stability of the periodic growth state is also considered. 1 INTRODUCTIONThe deep layers of sedimentary rocks such as shale and sandstone are usually intersected by systems of nearly parallel natural cracks either filled by mineral deposits or closed by creep over a million year life span. Their spacing is roughly uniform and is on the order of 0.1 m (rather than 1 m or 0.01m). These cracks likely play an important role in hydraulic fracturing for gas or oil recovery (aka fracking, fraccing or frac) (Rahimi-Aghdam et al., 2019, e.g.). Therefore, understanding the mechanism of their formation in the distant geologic past is of interest.What controls the spacing of the nearly parallel cracks in shale? According to the fracture mechanics alone, the crack spacing is arbitrary. If propagating parallel equidistant cracks are in a critical state, stability analysis shows that many cracks would have to stop growing, causing a great increase of their average spacing, which was obviously not the case (Bažant et al., 2014).more » « less
-
ABSTRACT:Creation of a fracture network in a hydraulic fracturing process is essential for subsurface energy extraction and CO2 sequestration. It is facilitated by reactivation of pre-existing intersecting weak layers and cemented cracks in the rock. In this study, a poromechanical model is developed for the hydraulic fracturing process in rocks containing such pre-existing weak layers. Based on the mixture theory, the crack band model is used to simulate the growth of a crack system. The governing equations with the parameters for hydromechanical coupling are derived, to describe the evolution of the opening and branching of cracks caused by water injection. Microplane model M7 is adopted to characterize the deformation and fracturing of the solid skeleton of the rock, and the Poiseuille law is used to characterize fluid flow through the hydraulic fractures. Numerical simulations are performed to reproduce and interpret recently published laboratory-scale hydraulic fracturing experiments conducted at Los Alamos National Laboratory (LANL). In these experiments, the rock was represented by confined plaster slabs containing orthogonal intersecting weak layers of higher porosity. Numerical simulations reveal how poromechanical characteristics such as the Biot coefficient and the fluid injection rate lead to various typical fracture modes observed in the experiments. These modes include formation of one dominant planar crack or various orthogonal fracture networks.more » « less
-
Abstract Englacial water transport is an integral part of the glacial hydrologic system, yet the geometry of englacial structures remains largely unknown. In this study, we explore the excitation of fluid resonance by small amplitude waves as a probe of englacial geometry. We model a hydraulic network consisting of one or more tabular cracks that intersect a cylindrical conduit, subject to oscillatory wave motion initiated at the water surface. Resulting resonant frequencies and quality factors are diagnostic of fluid properties and geometry of the englacial system. For a single crack–conduit system, the fundamental mode involves gravity-driven fluid sloshing between the conduit and the crack, at frequencies between 0.02 and 10 Hz for typical glacial parameters. Higher frequency modes include dispersive Krauklis waves generated within the crack and tube waves in the conduit. But we find that crack lengths are often well constrained by fundamental mode frequency and damping rate alone for settings that include alpine glaciers and ice sheets. Branching crack geometry and dip, ice thickness and source excitation function help define limits of crack detectability for this mode. In general, we suggest that identification of eigenmodes associated with wave motion in time series data may provide a pathway toward inferring englacial hydrologic structures.more » « less
-
Impacted with sufficiently large stress, a dense, initially liquidlike suspension can be forced into a solidlike state through a process known as shear jamming. While the onset of shear jamming has been investigated extensively, much less is known about the resulting solidlike state in the high-stress limit and, in particular, about its failure mode. We report on experiments that produce such high-stress failure by impacting dense suspensions with a cylindrical rod moving at controlled speed. Using suspensions of cornstarch particles we vary the impact speed over several orders of magnitude and change the fluid viscosity as well as the surface tension in order to identify the conditions for failure. The results are compared with similarly dense suspensions of potato starch or polydisperse silica particles. In all cases where the shear-jammed suspension fails by fracturing, similar to brittle solids, we observe two types of cracks: a primary circular crack around the impacting rod followed by secondary radial cracks. Mapping out the onset of radial fracturing for different particle volume fractions and impact speeds, we identify the requirements for failure via crack formation to occur with at least 50% likelihood and record the corresponding normal stress on the impactor. We find that this likelihood is not particularly sensitive to changes in particle diameter, but increases when the solvent's viscosity or its surface tension are reduced. In the state diagram for dense suspensions we use these data to delineate the upper limit of shear-jammed rigidity and the crossover into a fracture regime at large and large , several orders of magnitude above the stress required for the onset of shear jamming. We find that the onset of fracturing in many cases is correlated with signatures of internal ductile deformation of the shear-jammed material underneath the impactor, observable in as a function of axial strain. However, for smaller suspension volumes and larger impact speeds, we find strain hardening up to the point of fracturing. This more brittle behavior results in a modulus that, just before crack formation, is roughly an order of magnitude larger than what we observe in shear-jammed suspensions undergoing internal ductile deformation.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1093/gji/ggaf142
