Despite the critical role of sintering phenomena in constraining the long-term durability of nano-sized particles, a clear understanding of nanoparticle sintering has remained elusive due to the challenges in atomically tracking the neck initiation and discerning different mechanisms. Through the integration of in-situ transmission electron microscopy and atomistic modeling, this study uncovers the atomic dynamics governing the neck initiation of Pt-Fe nanoparticles via a surface self-diffusion process, allowing for coalescence without significant particle movement. Real-time imaging reveals that thermally activated surface morphology changes in individual nanoparticles induce significant surface self-diffusion. The kinetic entrapment of self-diffusing atoms in the gaps between closely spaced nanoparticles leads to the nucleation and growth of atomic layers for neck formation. This surface self-diffusion-driven sintering process is activated at a relatively lower temperature compared to the classic Ostwald ripening and particle migration and coalescence processes. The fundamental insights have practical implications for manipulating the morphology, size distribution, and stability of nanostructures by leveraging surface self-diffusion processes.
more »
« less
EFFECT OF PARTICLE SHAPE ON NECK GROWTH AND SHRINKAGE OF NANOPARTICLES
Sintering of nanoparticles to create films and patterns of functional materials is emerging as a key manufacturing process in applications like flexible electronics, solar cells and thin-film devices. Further, there is the emerging potential to use nanoparticle sintering to perform additive manufacturing as well. While the effect of nanoparticle size on sintering has been well studied, very little attention has been paid to the effect of nanoparticle shape on the evolution of sintering. This paper uses Molecular dynamics (MD) simulations to determine the influence of particle shape on shrinkage and neck growth for two common nanoparticle shape combinations, i.e., sphere-sphere and sphere-cylinder nanoparticles of different sizes. These sintering indicators are examined at two different temperature ramps. The results from this work show that depending on their relative sizes, degree of neck growth and shrinkage are both significantly affected by the nanoparticle shape. The possibility of using this phenomenon to control density and stresses during nanoparticle sintering are discussed.
more »
« less
- Award ID(s):
- 1809289
- PAR ID:
- 10063289
- Date Published:
- Journal Name:
- 2017 Manufacturing Science and Engineering Conference
- Page Range / eLocation ID:
- 6
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Sintering of nanoparticles deposited onto rigid or flexible substrate is required for many devices that use continuous and patterned thin films. An emerging need in this area is to perform nanoparticle sintering under ambient conditions, at high speeds, and with throughput that is compatible with high speed nanoparticle deposition techniques. Intense Pulsed Light sintering (IPL) uses a high energy, broad area and broad spectrum beam of xenon lamp light to sinter metallic and non-metallic nanoparticles. The capability of IPL to meet the above needs has been demonstrated. This paper experimentally examines temperature evolution and densification during IPL. It is shown, for the first time, that temperature rise and densification in IPL are related to each other. A coupled optical-thermal-sintering model on the nanoscale is developed, to understand this phenomenon. This model is used to show that the change in nanoscale shape of the nanoparticle ensemble due to sintering, reduces the optically induced heating as the densification proceeds, which provides a better explanation of experimental observations as compared to current models of IPL. The implications of this new understanding on the performance of IPL are also discussed.more » « less
-
more » « less
Abstract Nanoparticle pollution has been shown to affect various organisms. However, the effects of nanoparticles on species interactions, and the role of species traits, such as body size, in modulating these effects, are not well‐understood. We addressed this issue using competing freshwater phytoplankton species exposed to copper oxide nanoparticles. Increasing nanoparticle concentration resulted in decreased phytoplankton species growth rates and community productivity (both abundance and biomass). Importantly, we consistently found that nanoparticles had greater negative effects on species with smaller cell sizes, such that nanoparticle pollution weakened the competitive dominance of smaller species and promoted species diversity. Moreover, nanoparticles reduced the growth rate differences and competitive ability differences of competing species, while having little effect on species niche differences. Consequently, nanoparticle pollution reduced the selection effect on phytoplankton community abundance, but increased the selection effect on community biomass. Our results suggest cell size as a key functional trait to consider when predicting phytoplankton community structure and ecosystem functioning in the face of increasing nanopollution.
-
Microscale continuous thin films or patterned conductive structures find applications in thin film electronics, energy generation and functional sensor systems. An emerging alternative to conventional vacuum based deposition of such structures is the additive deposition and sintering of conductive nanoparticles, to enable low temperature, low-cost and low energy fabrication. While significant work has gone into additive deposition of nanoparticles the realization of the above potential needs nanoparticle sintering methods that are equally low-cost, in-situ, ambient condition and desktop-sized in nature. This work demonstrates the integration of non-laser based, low-cost and small footprint optical energy sources for ambient condition sintering of conductive nanoparticles, with wide-area aerosol jet based additive printing of nanoparticle inks. The nanoparticle sintering is characterized by quantifying the sintering temperatures, sintered material conductivity, crystallinity, optical properties, thickness and microscale morphology in terms of the sintering parameters. It is shown that such optical sintering sources can be further integrated with inkjet printing as well, and the implications on new paradigms for hybrid additive-more » « less
-
One of the main challenges facing the expansion of Additive Manufacturing (AM) is the minimum feature sizes which these processes are able to achieve. Microscale Selective Laser Sintering (μ-SLS) is a novel Additive Manufacturing process created to meet this limitation by precisely laser sintering nanoparticles to give a better control over feature sizes. With the development of this new process, there is a concurrent need for models, which can predict the material properties of the sintering nanoparticles. To this end, this paper presents a novel simulation created to predict the electrical resistivity of sintered copper nanoparticles. Understanding the electrical resistivity of nanoparticles under sintering is useful for quantifying the rate of sintering and has applications such as predicting how the nanoparticles will fuse together when subjected to laser irradiation. Such a prediction allows for in situ corrections to be made to the sintering process to account for heat spreading beyond the intended laser irradiation targets. For these applications, it is important to ensure that the predictions of electrical resistivity from the simulations are accurate. This validation must be done against experimental data and since such experimental data does not currently exist, this paper also presents electrical resistivity data for the laser sintering of copper nanoparticles. In summary, this paper details the simulation methodology for predicting electrical resistivity of laser-sintered copper nanoparticles as well as validation of these simulations using electrical resistivity data from original sintering experiments. The key findings of this work are that the simulations can be used to predict electrical resistivity measurements for sintering of actual copper nanoparticles when the copper nanoparticles do not include other materials such as polymer coatings.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- The DOI is not currently available.
