skip to main content

Explore Research Products in the NSF-PAR

Title: Synthesis and Characterization of the Atomic Laminate Mn2AlB2
Herein, we synthesize dense, predominantly single-phase polycrystalline samples of the Mn2AlB2 ternary compound, using reactive hot-pressing of manganese, aluminum, and boron powder mixtures under vacuum. With a Vickers hardness of 8.7 GPa, Mn2AlB2 is relatively soft for a transition metal boride and lacked dominant cracks at the corners of the indentations. With Young’s and shear moduli of 243 GPa and 102 GPa at 300 K, respectively, it is reasonably stiff. The Poisson’s ratio is calculated to be 0.19. With compressive strengths of 1.24 ± 0.1 GPa, the samples were quite strong considering the grain size (1–15 μm). The electrical resistivity at 300 K was ∼5 μΩm and decreased linearly upon cooling. At 0.0036 K−1, the temperature coefficient of resistivity was relatively high compared to MoAlB. The average linear thermal expansion coefficient was also found to be relatively high at 18.6 × 10-6 K−1 from 298 to 1173 K. Mn2AlB2 was not thermally stable above ∼1379 K. While Mn2AlB2 was not machinable with conventional tooling, intriguingly, high-speed carbide tools bits readily penetrate the surface – with no cracking or chipping for a few millimeters – before stopping.  more » « less
Award ID(s):
1729350
NSF-PAR ID:
10073594
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
Journal of the European Ceramic Society
ISSN:
0955-2219
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; ; ; ; et al ( , Materials Advances)
    null (Ed.)
    FeAs 2−x Se x ( x = 0.30–1.0) samples were synthesized as phase pure powders by conventional solid-state techniques and as single crystals ( x = 0.50) from chemical vapor transport. The composition of the crystals was determined to be Fe 1.025(3) As 1.55(3) Se 0.42(3) , crystallizing in the marcasite structure type, Pnnm space group. FeAs 2−x Se x (0 < x < 1) was found to undergo a marcasite-to-arsenopyrite ( P 2 1 / c space group) structural phase transition at x ∼ 0.65. The structures are similar, with the marcasite structure best described as a solid solution of As/Se, whereas the arsenopyrite has ordered anion sites. Magnetic susceptibility and thermoelectric property measurements from 300–2 K were performed on single crystals, FeAs 1.50 Se 0.50 . Paramagnetic behavior is observed from 300 to 17 K and a Seebeck coefficient of −33 μV K −1 , an electrical resistivity of 4.07 mΩ cm, and a very low κ l of 0.22 W m −1 K −1 at 300 K are observed. In order to determine the impact of the structural transition on the high-temperature thermoelectric properties, polycrystalline FeAs 2−x Se x ( x = 0.30, 0.75, 0.85, 1.0) samples were consolidated into dense pellets for measurements of thermoelectric properties. The x = 0.85 sample shows the best thermoelectric performance. The electronic structure of FeAsSe was calculated with DFT and transport properties were approximately modeled above 500 K. 
    more » « less
  2. ; ; ( , Materials Advances)
    Thermoelectric materials can convert heat into electricity. They are used to generate electricity when other power sources are not available or to increase energy efficiency by recycling waste heat. The Yb 21 Mn 4 Sb 18 phase was previously shown to have good thermoelectric performance due to its large Seebeck coefficient (∼290 μV K −1 ) and low thermal conductivity (0.4 W m −1 K −1 ). These characteristics stem respectively from the unique [Mn 4 Sb 10 ] 22− subunit and the large unit cell/site disorder inherent in this phase. The solid solutions, Yb 21 Mn 4− x Cd x Sb 18 ( x = 0, 0.5, 1.0, 1.5) and Yb 21− y Ca y Mn 4 Sb 18 ( y = 3, 6, 9, 10.5) have been prepared, their structures characterized and thermoelectric properties from room temperature to 800 K measured. A detailed look into the structural disorder for the Cd and Ca solid solutions was performed using synchrotron powder X-ray diffraction and pair distribution function methods and shows that these are highly disordered structures. The substitution of Cd gives rise to more metallic behavior whereas Ca substitution results in high resistivity. As both Cd and Ca are isoelectronic substitutions, the changes in properties are attributed to changes in the electronic structure. Both solid solutions show that the thermal conductivities remain extremely low (∼0.4 W m −1 K −1 ) and that the Seebeck coefficients remain high (>200 μV K −1 ). The temperature dependence of the carrier mobility with increased Ca substitution, changing from approximately T −1 to T −0.5 , suggests that another scattering mechanism is being introduced. As the bonding changes from polar covalent with Yb to ionic for Ca, polar optical phonon scattering becomes the dominant mechanism. Experimental studies of the Cd solid solutions result in a max zT of ∼1 at 800 K and, more importantly for application purposes, a ZT avg ∼ 0.6 from 300 K to 800 K. 
    more » « less
  3. ; ( , Journal of Geophysical Research: Solid Earth)
    Abstract

    Hydrogen solubility was determined in olivine and orthopyroxene under water‐saturated conditions atP = 3–5 GPa andT = 1373–1573 K. For olivine, polycrystalline samples were prepared from San Carlos olivine, and for orthopyroxene synthetic samples were prepared from oxide mixture containing 1.5–5 wt% of Al2O3. Olivine and orthopyroxene were placed next to each other and annealed under various pressure and temperature conditions for 3–5 hr. Hydrogen content was measured across each sample by FTIR spectroscopy. Under the water‐saturated conditions, the hydrogen solubility in olivine increases with pressure and temperature similar to previous results. Hydrogen solubility in Al2O3‐bearing orthopyroxene also increases with temperature and pressure for a fixed Al2O3content. Based on these observations we calculated the partition coefficients of hydrogen between orthopyroxene and olivine assuming the fugacity dependence of hydrogen solubility in olivine and Al2O3‐bearing orthopyroxene reported by previous studies. We find that the partition coefficient depends weakly on temperature but strongly on pressure and water fugacity. Our results are extended to an open system where Al2O3content in orthopyroxene changes with pressure and temperature. At relatively low pressures and low water fugacity (in the lithosphere (shallower than ∼50 km)), the partition coefficient is high and a majority of hydrogen is present in orthopyroxene. Consequently, the influence of water on the bulk physical properties is small. In contrast, at higher pressures and higher water fugacity (in the asthenosphere), the partition coefficient is smaller and a substantial amount of hydrogen is present in olivine. Consequently, hydrogen has a strong effect on the bulk properties of the asthenosphere reducing viscosity and increasing electrical conductivity.

     
    more » « less
  4. ; ; ( , Physical Chemistry Chemical Physics)
    Experimental techniques, such as cryo-electron microscopy, require biological samples to be recovered at cryogenic temperatures ( T ≈ 100 K) with water being in an amorphous ice state. However, (bulk) water can exist in two amorphous ices at P < 1 GPa, low-density amorphous (LDA) ice at low pressures and high-density amorphous ice (HDA) at high pressures; HDA is ≈20–25% denser than LDA. While fast/plunge cooling at 1 bar brings the sample into LDA, high-pressure cooling (HPC), at sufficiently high pressure, produces HDA. HDA can also be produced by isothermal compression of LDA at cryogenic temperatures. Here, we perform classical molecular dynamics simulations to study the effects of LDA, HDA, and the LDA–HDA transformation on the structure and hydration of a small peptide, polyalanine. We follow thermodynamic paths corresponding to (i) fast/plunge cooling at 1 bar, (ii) HPC at P = 400 MPa, and (iii) compression/decompression cycles at T = 80 K. While process (i) produced LDA in the system, path (iii) produces HDA. Interestingly, the amorphous ice produced in process (ii) is an intermediate amorphous ice (IA) with properties that fall in-between those of LDA and HDA. Remarkably, the structural changes in polyalanine are negligible at all conditions studied (0–2000 MPa, 80–300 K) even when water changes among the low and high-density liquid states as well as the amorphous solids LDA, IA, and HDA. The similarities and differences in the hydration of polyalanine vitrified in LDA, IA, and HDA are described. Since the studied thermodynamic paths are suitable for the cryopreservation of biomolecules, we also study the structure and hydration of polyalanine along isobaric and isochoric heating paths, which can be followed experimentally for the recovery of cryopreserved samples. Upon heating, the structure of polyalanine remains practically unchanged. We conclude with a brief discussion of the practical advantages of (a) using HDA and IA as a cryoprotectant environment (as opposed to LDA), and (b) the use of isochoric heating as a recovery process (as opposed to isobaric heating). 
    more » « less
  5. ; ; ( , Journal of The Electrochemical Society)

    Temperature dependence studies of electrochemical parameters provide insight into electron transfer processes. In cases where adding excess electrolyte causes experimental complications, e.g., colloidal systems, organic or biological samples, it is preferable to deal with the high resistivity of the medium. We validate the use of unsupported and weakly-supported solutions in thermoelectrochemical experiments. The temperature dependence of the diffusion coefficient allows calibration of the steady-state current to measure changes when a continuous-wave (CW) ultraviolet laser,λ= 325 nm, illuminates an ultramicroelectrode (UME) from the front. Calibrating the steady-state current ratios, before and after heating with a thermostatic bath, allows temperature measurements within an accuracy of 0.6 K. The solutions are without supporting electrolytes in methanol, a volatile solvent, and we use a model that accurately describes the viscosity and temperature dependence of the solvent. We calculated the temperature and derived an equation to estimate the error in the temperature measurement. A numeric method yields satisfactory results, considering the changes for both diffusion coefficients and viscosity explicitly, and predicts the thermostatic temperature bath, agreeing with the theoretical model’s error. In unsupported solutions, the ferrocene diffusion coefficient and the iodide apparent diffusion coefficient follow the expected increase with temperature. Under CW laser illumination, the UME temperature increase is: ΔT = 4 ± 1 K.

     
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email