An official website of the United States government
Fast mechanical disconnect switches are an integral part of hybrid circuit breakers, which are proposed as protection devices to clear faults in medium voltage distribution systems. Compared to their conventional counterparts, hybrid circuit breakers can have the ability to limit the fault current, which could allow more interconnections between substations with advantages with respect to grid reliability and resiliency. Furthermore, they enable the integration of distributed generation such as small solar power installations without expensive changes to the grid infrastructure. The proposed design of an ultrafast mechanical disconnect switch operates in vacuum, carries continuous current similar to conventional vacuum interrupters, opens at current zero, features minimum moving mass, and has an open contact separation of less than a millimeter. The limited separation distance requires an optimized contact geometry to keep the electric field within safe limits, minimize the moving mass, and reduce contact resistance. This paper proposes different contact geometries and uses finite element analysis to compare the contact geometries with respect to maximum electric field, mass, and contact resistance. Reductions of mass by 50% and reduction of contact resistance of 10% have been achieved.
more »
« less
Theoretical and Experimental Work on Optimal Contact Geometries on Fast Mechanical Disconnect Switches
Fast mechanical disconnect switches (FMS) are an integral part of hybrid circuit breakers, which are proposed as protection devices to clear faults in medium voltage distribution systems. The proposed FMS is a vacuum switch that is operated by an amplified piezoelectric actuator. Such actuators enable unprecedented speed and contact separation in less than one millisecond. The limitations that come with such designs are the low contact separation of typically less than one millimeter in open position and low contact force in the order of 100 N in closed position. This requires a new design of the contacts to operate under such constraints. The geometry of the contacts must be carefully designed to minimize electrical resistance when closed and minimize electric field enhancement when open. The paper presents finite element analysis and experimental results with the aim of identifying the most suitable contact geometry for FMS. The experiments show that optimized contact geometries have up to 40% less resistance than the initial spherical geometry.
more »
« less
- Award ID(s):
- 1700887
- PAR ID:
- 10100181
- Date Published:
- Journal Name:
- 2018 IEEE Holm Conference on Electrical Contacts
- Page Range / eLocation ID:
- 24 to 30
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Adhesive contacts which possess a dominant stress concentration, such as at the contact edge in spherical junctions or at the detachment front in a peeling film, are well studied. More complex adhesive junction geometries, such as mushroom-shaped fibrils in bioinspired micropatterned dry adhesives, have exhibited a complex dependence of adhesive strength on the presence of interfacial defects within the contact. This has led to the emergence of statistical variation of the local behavior among micropatterned sub-contacts. In order to examine the interplay between geometry and interfacial defect character in control of the adhesive strength, the model system of a stiff cylindrical probe on an elastic layer is examined. Both experiments (glass on PDMS) and cohesive zone finite element simulations are performed, with analytical asymptotic limits also considered. The thickness of the elastic layer is varied to alter the interfacial stress distribution, with thinner layers having a reduced edge stress concentration at the expense of increased stress at the contact center. The size and position of manufactured interfacial defects is varied. It is observed that for the thickest substrates the edge stress concentration is dominant, with detachment propagating from this region regardless of the presence of an interfacial defect within the contact. Only very large center defects, with radius greater than half of that of the contact influence the adhesive strength. This transition is in agreement with analytical asymptotic limits. As the substrate is made thinner and the stress distribution changes, a strong decay in adhesive strength with increasing center defect radius emerges. For the thinnest substrate the flaw-insensitive upper bound is approached, suggesting that this decay is dominated by a reduction in the contact area. For penny-shaped defects at increasing radial positions, the adhesive strength for the thinnest substrates becomes non-monotonic. This confirms an intricate interplay between the geometry-controlled interfacial stress distribution and the size and position of interfacial defects in adhesive contacts, which will lead to statistical variation in strength when defects form due to surface roughness, fabrication imperfections, or contaminant particles.more » « less
-
Adhesive contacts which possess a dominant stress concentration, such as at the contact edge in spherical junctions or at the detachment front in a peeling film, are well studied. More complex adhesive junction geometries, such as mushroom-shaped fibrils in bioinspired micropatterned dry adhesives, have exhibited a complex dependence of adhesive strength on the presence of interfacial defects within the contact. This has led to the emergence of statistical variation of the local behavior among micropatterned sub-contacts. In order to examine the interplay between geometry and interfacial defect character in control of the adhesive strength, the model system of a stiff cylindrical probe on an elastic layer is examined. Both experiments (glass on PDMS) and cohesive zone finite element simulations are performed, with analytical asymptotic limits also considered. The thickness of the elastic layer is varied to alter the interfacial stress distribution, with thinner layers having a reduced edge stress concentration at the expense of increased stress at the contact center. The size and position of manufactured interfacial defects is varied. It is observed that for the thickest substrates the edge stress concentration is dominant, with detachment propagating from this region regardless of the presence of an interfacial defect within the contact. Only very large center defects, with radius greater than half of that of the contact influence the adhesive strength. This transition is in agreement with analytical asymptotic limits. As the substrate is made thinner and the stress distribution changes, a strong decay in adhesive strength with increasing center defect radius emerges. For the thinnest substrate the flaw-insensitive upper bound is approached, suggesting that this decay is dominated by a reduction in the contact area. For penny-shaped defects at increasing radial positions, the adhesive strength for the thinnest substrates becomes non-monotonic. This confirms an intricate interplay between the geometry-controlled interfacial stress distribution and the size and position of interfacial defects in adhesive contacts, which will lead to statistical variation in strength when defects form due to surface roughness, fabrication imperfections, or contaminant particles.more » « less
-
Recent technology development of logic devices based on 2-D semiconductors such as MoS2, WS2, and WSe2 has triggered great excitement, paving the way to practical applications. Making low-resistance p-type contacts to 2-D semiconductors remains a critical challenge. The key to addressing this challenge is to find high-work function metallic materials which also introduce minimal metal-induced gap states (MIGSs) at the metal/semiconductor interface. In this work, we perform a systematic computational screening of novel metallic materials and their heterojunctions with monolayer WSe2 based on ab initio density functional theory and quantum device simulations. Two contact strategies, van der Waals (vdW) metallic contact and bulk semimetallic contact, are identified as promising solutions to achieving Schottky-barrier-free and low-contact-resistance p-type contacts for WSe2 p-type field-effect transistor (pFETs). Good candidates of p-type contact materials are found based on our screening criteria, including 1H-NbS2, 1H-TaS2, and 1T-TiS2 in the vdW metal category, as well as Co3Sn2S2 and TaP in the bulk semimetal category. Simulations of these new p-type contact materials suggest reduced MIGS, less Fermi-level pinning effect, negligible Schottky barrier height and small contact resistance (down to 20 Ωμm )more » « less
-
Abstract The performance of electronic and optoelectronic devices is dominated by charge carrier injection through the metal–semiconductor contacts. Therefore, creating low-resistance electrical contacts is one of the most critical challenges in the development of devices based on new materials, particularly in the case of two-dimensional semiconductors. Herein, we report a strategy to reduce the contact resistance of MoS 2 via local pressurization. We fabricated electrical contacts using an atomic force microscopy tip and applied variable pressure ranging from 0 to 25 GPa. By measuring the transverse electronic transport properties, we show that MoS 2 undergoes a reversible semiconducting-metallic transition under pressure. Planar devices in field effect configuration with electrical contacts performed at pressures above ∼15 GPa show up to 30-fold reduced contact resistance and up to 25-fold improved field-effect mobility when compared to those measured at low pressure. Theoretical simulations show that this enhanced performance is due to improved charge injection to the MoS 2 semiconductor channel through the metallic MoS 2 phase obtained by pressurization. Our results suggest a novel strategy for realizing improved contacts to MoS 2 devices by local pressurization and for exploring emergent phenomena under mechano-electric modulation.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/HOLM.2018.8611645
