Cadmium telluride (CdTe) solar cells are a promising photovoltaic (PV) technology for producing power in space owing to their high-efficiency (> 22.1 %), potential for specific power, and cost-effective manufacturing processes. In contrast to traditional space PVs, the high-Z (atomic number) CdTe absorbers can be intrinsically robust under extreme space radiation, offering long-term stability. Despite these advantages, the performance assessment of CdTe solar cells under high-energy particle irradiation (e.g., photons, neutrons, charged particles) is limited in the literature, and their stability is not comprehensively studied. In this work, we present the PV response of n-CdS / p-CdTe PVs under accelerated neutron irradiation. We measure PV properties of the devices at different neutron/photon doses. The equivalent dose deposited in the CdTe samples is simulated with deterministic and Monte Carlo radiation transport methods.
Thin-film CdTe solar cells were synthesized on a fluorine-doped tin oxide (FTO) coated glass substrate (≈ 4 cm × 4 cm). CdS:O (≈ 100 nm) was reactively RF sputtered in an oxygen/argon ambient followed by a close-spaced sublimation deposition of CdTe (≈ 3.5 μm) in an oxygen/helium ambient. The sample was exposed to a 10 min vapor CdCl2 in oxygen/helium ambient at 430˚C. The samples were exposed to a wet CuCl2 solution prior to anneal 200ºC. A gold back-contact was formed on CdTe via thermal evaporation. The final sample contains 16 CdTe devices. For neutron irradiation, we cleaved the CdTe substrate into four samples and exposed two samples to ≈ 90 kW reactor power neutron radiation for 5.5 hours and 8.2 hours, respectively, in our TRIGA (Training, Research, Isotopes, General Atomics) reactor.
We observed a noticeable color change of the glass substrates to brown after the neutron/gamma reactor exposure. Presumably, the injected high-energy neutrons caused the breaking of chemical bonds and the displacement of atoms in the glass substrates, creating point defects and color centers. The I-V characteristics showed noticeable deterioration with over 8 hour radiations. Specifically, the saturation current of the control devices was ≈ 25 nA increasing to 1 μA and 10 μA for the 5.5-hour and 8.2-hour radiated samples, respectively. The turn-on voltage of the control devices (≈ 0.85 V) decreased with the irradiated sample (≈ 0.75 V for 5.5-hour and ≈ 0.5 V for 8.2-hour exposures), implying noticeable radiation damage occurred at the heterojunction. The higher values of the ideality factor for irradiated devices (n > 2.2) compared to that of the control devices (n ≈ 1.3) also support the deterioration of the p-n junction. We observed the notable decrease in shunt resistance (RSH) and the increase in series resistance (Rs) with the neutron dose. It is possible that Cu ions introduced during the CuCl2 treatment may migrate into CdTe grain boundaries (GBs). The presence of Cu ions at GBs can create additional leakage paths for photocarrier transport, deteriorating the overall PV performance.
We estimated the radiation dose of CdTe in comparison to Si (conventional PV) using a UUTR model (e.g., MCNP6 2D UTR Reactor simulations). In this model, we simulated Si and CdTe at the center point of the triangular fuel lattice and used an “unperturbed flux” tally in the water. Our simulations yielded a dose rate of 6916 Gy/s of neutrons and 16 Gy/s of photons for CdTe, and 1 Gy/s of neutrons and 21 Gy/s of photons for Si (doses +/- <1%). The large dose rate of neutrons in CdTe is mainly attributed to the large thermal neutron absorption cross-section of 113Cd. Based on this estimation, we calculate that the exposure of our CdTe PVs is equivalent to several million years in LEO (Low-Earth Orbit), or about 10,000 years for Si in LEO. Currently, we are working on a low-dose neutron/photon radiation on CdTe PVs and their light I-Vs and microstructural characterizations to gain better understanding on the degradation of CdTe PVs.
more »
« less
Dramatic Recrystallization During CdCl2 Treatment of Evaporated CdTe Thin Filmsa
In this work, we report the different effects of CdCl 2 treatment on CdTe films deposited by thermal evaporation onto CdS and MgZnO (MZO) buffer layers. The main finding, which is relevant for understanding recent advances in CdTe device efficiency, is that few-μm thick CdTe films deposited on MZO can be induced to completely recrystallize forming a film consisting of grains that span the film thickness and are up to 30 μm laterally. On CdS buffer layers, the changes in microstructure with Cl treatment are much less pronounced and the final microstructure is less ideal for thin film photovoltaics. We propose a thermodynamic framework for understanding the microstructural changes during CdCl 2 treatment which can assist in understanding the wide range of behaviors observed across the many CdTe thin film solar cell fabrication procedures.
more »
« less
- Award ID(s):
- 1711885
- NSF-PAR ID:
- 10121610
- Date Published:
- Journal Name:
- 2018 IEEE 7th World Conference on Photovoltaic Energy Conversion (WCPEC) (A Joint Conference of 45th IEEE PVSC, 28th PVSEC & 34th EU PVSEC)
- Page Range / eLocation ID:
- 176-179
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Spectroscopic ellipsometry (SE) was performed on CuIn Se 2 (CIS) thin films and solar cells with a goal toward optimizing this low bandgap absorber for tandem applications. The CIS thin films and the absorbers in devices were deposited by one-stage thermal co-evaporation on silicon and on Mo-coated soda-lime glass substrates in a deposition system that has yielded CuIn 1-x Ga x Se 2 (CIGS) cells with > 17% efficiency using standard thickness (2.0 μm)x = 0.3 absorbers and > 13% using 0.7 μm low-Ga absorbers. In this study, a mapping capability for CIS Cu stoichiometry y = [Cu]/[In] over the film area was established based on a y-dependent parametric dielectric function (ε 1 , ε 2 ) with bandgap critical point E g decreasing linearly from 1.030 eV for y = 0.7 to 1.016 eV for y = 1.1. In addition, a full set of (ε 1 , ε 2 ) spectra measured for the CIS cell components enables analysis of SE data in terms of an accurate structural model for the device. With this model, spectra in the external quantum efficiency can be predicted, and deviations from this prediction can be attributed to incomplete collection of photogenerated electrons and holes as simulated with a carrier collection profile.more » « less
-
more » « less
Abstract Earth‐abundant and air‐stable Cu2BaSnS4−
x Sex (CBTSSe) and related thin‐film absorbers are regarded as prospective options to meet the increasing demand for low‐cost solar cell deployment. Devices based on vacuum‐deposited CBTSSe absorbers have achieved record power conversion efficiency (PCE) of 5.2% based on a conventional device structure using CdS buffer and i‐ZnO/indium tin oxide (ITO) window layers, with open‐circuit voltage (V OC) posing the major bottleneck for improving solar cell performance. The current study demonstrates a >20% improvement inV OC(from 0.62 to 0.75 V) and corresponding enhancement in PCE (from 5.1% to 6.2% without antireflection coating; to 6.5% with MgF2antireflection coating) for solution‐deposited CBTSSe solar cells. This performance improvement is realized by introducing an alternative successive ionic layer adsorption and reaction‐deposited Zn1−x Cdx S buffer combined with sputtered Zn1−x Mgx O/Al‐doped ZnO window/top contact layer, which offers lower electron affinities relative to the conventional CdS/i‐ZnO/ITO stack and better matching with the low electron affinity of CBTSSe. A combined experimental (temperature‐ and light intensity‐dependentV OCmeasurements) and device simulation (SCAPS‐1D) evaluation points to the importance of addressing relative band offsets for both the buffer and window layers relative to the absorber in mitigating interfacial recombination and optimizing CBTSSe solar cell performance. -
more » « less
Abstract We fabricate and characterize methylammonium lead halide perovskite film as a novel back contact to CdTe thin‐film solar cells. We apply ~0.75 μm perovskite film at the interface of CdCl2‐activated and Cu‐doped CdTe surface and complete the device with Au back contact. We use Cu/Au back contact as a reference to compare results with novel back contact. Our investigation shows that incorporation of thin layer of perovskite film before the back contact metal reduces back contact barrier effect and improves fill factor (FF) and open‐circuit voltage (VOC) of the solar cells. Our low temperature JV results prove that thin‐film perovskite is a very necessary component in CdTe solar cells to reduce back contact barrier, to minimize interface or surface recombination, to improve collection efficiencies, and to increase the efficiency of solar cells. Our best device shows 7% increase in VOCto 0.875 V and ~7% increase in FF with the highest FF of 81%, and solar cell's efficiency finally increases by 10% with the use of MAPb(I1‐xBrx)3as an interface layer.
-
Development of copper-free ZnTe buffer layers for CdTe-based solar cells is an important avenue for improving stability. Group V elements offer a path towards that goal. This work explores two group V elements, phosphorous and antimony, as candidates for making copper-free p-type ZnTe buffer layer using thermal evaporation. It is found that incorporation of both elements into ZnTe film can easily be done. In addition, as deposited ZnTe films are Te-rich and Cd1-xZnxTe alloys form upon co-evaporation of ZnTe and Cd3P2 , improving crystallinity and stoichiometry of the film. Activation of P poses a challenge, while ZnTe films with Sb produced good sheet resistance values.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/PVSC.2018.8547287
