skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Characterization of thin CdTe solar cells with a CdSeTe front layer
ABSTRACT Thin CdTe photovoltaic device efficiencies show significant improvement with the incorporation of a CdSeTe alloy layer deposited between a MgZnO emitter and CdTe absorber. CdTe and CdSeTe/CdTe devices fabricated by close-space sublimation with a total absorber thickness of 1.5 µm are studied using microscopy measurements and show minimal diffusion of Se into the CdTe. Current loss analysis shows that the CdSeTe layer is the primary absorber in the CdSeTe/CdTe structure, and fill factor loss analysis shows that ideality-factor reduction is the dominant mechanism of fill factor loss. Improvement in the CdSeTe/CdTe absorber quality compared to CdTe is also reflected in spectral and time-resolved photoluminescence measurements. Current density vs. voltage measurements show an increase in current density of up to 2 mA/cm 2 with the addition of CdSeTe due to a band gap shift from 1.5 to 1.42 eV for CdTe and CdSeTe/CdTe absorbers respectively. Voltage deficit is lower with the incorporation of the CdSeTe layer, corroborated by improved electroluminescence intensity. The addition of CdSeTe into CdTe device structures has increased device efficiencies from 14.7% to 15.6% for absorbers with a total thickness less than two microns.  more » « less
Award ID(s):
1726898
PAR ID:
10122049
Author(s) / Creator(s):
; ; ;
Date Published:
Journal Name:
MRS Advances
Volume:
4
Issue:
37
ISSN:
2059-8521
Page Range / eLocation ID:
2053 to 2062
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; ; (, Solar RRL)
    Grading of bandgap by alloying CdTe with selenium to form a CdSexTe1–x/CdTe‐graded bilayer device has led to a device efficiency over 19%. A CdSexTe1–xabsorber would increase the short‐circuit current due to its lower bandgap but at the expense of open‐circuit voltage. It has been demonstrated that adding a CdTe layer at the back of such a CdSexTe1–xfilm reduces the voltage deficit caused by the lower bandgap of absorber from selenium alloying while maintaining the higher short‐circuit current. This leads to a photovoltaic device that draws advantage from both materials with an efficiency greater than either of them. Herein, a detailed account using device data, ultraviolet photoelectron spectroscopy, electron microscopy, and first‐principles density functional theory modeling is provided, which shows that CdTe acts as an electron reflector for CdSexTe1–x. 
    more » « less
  2. ; ; ; ; ; ; (, Conference record of the IEEE Photovoltaic Specialists Conference)
    Cadmium telluride and silicon are among the widely used absorber materials in photovoltaic industry. A tandem solar cell of these two can absorb significant portion of solar spectrum to yield high efficiency due to the added voltage of the two solar cells. On basis of low-cost production, a CdTe/Si cell has the potential to produce low-cost and high efficiency tandem PV. The CdTe top cell in a substrate configuration is essential to achieve a tandem between CdTe and Si. A functional CdS/CdTe solar cell in the substrate configuration was fabricated on a Si wafer. Current -Voltage measurements show a diode-like curve with lower J-V parameters compared to standard CdS/CdTe cells. SCAPS simulations were performed to identify possible reasons for poor performance and help improve the device performance. 
    more » « less
  3. ; ; ; ; (, Solar RRL)
    Air‐stable p‐type SnF2:Cs2SnI6with a bandgap of 1.6 eV has been demonstrated as a promising material for Pb‐free halide perovskite solar cells. Crystalline Cs2SnI6phase is obtained with CsI, SnI2, and SnF2salts in gamma‐butyrolactone solvent, but not with dimethyl sulfoxide andN,N‐dimethylformamide solvents. Cs2SnI6is found to be stable for at least 1000 h at 100 °C when dark annealed in nitrogen atmosphere. In this study, Cs2SnI6has been used in a superstrate n–i–p planar device structure enabled by a spin‐coated absorber thickness of ≈2 μm on a chemical bath deposited Zn(O,S) electron transport layer. The best device power conversion efficiency reported here is 5.18% withVOCof 0.81 V, 9.28 mA cm−2JSC, and 68% fill factor. The dark saturation current and diode ideality factor are estimated as 1.5 × 10−3 mA cm−2and 2.18, respectively. The devices exhibit a highVOCdeficit and low short‐circuit current density due to high bulk and interface recombination. Device efficiency can be expected to increase with improvement in material and interface quality, charge transport, and device engineering. 
    more » « less
  4. ; ; (, Electronic Materials Conference)
    Rapid progress has been achieved in thin film CdTe solar cells, reaching a power conversion efficiency of 22.1 %. Researchers demonstrated a short-circuit current density (Jsc) of ≈ 31 mA/cm2 and a fill factor (FF) of ≈ 79 %, close to the theoretically calculated maximum values. However, the open-circuit voltage (Voc) remains below 0.9 V, much lower than the estimated Voc of 1.2 V. One strategy to improve the Voc is to implement a passivated back-contact on CdTe that can reduce the recombination by repelling minority carriers at the surface (i.e., electrons in CdTe). An aluminum oxide thin film (Al2O3) is an attractive candidate owing to its innate fixed negative charges (1012 ~ 1013 cm-2). Here, we use a patterned Al2O3 layer on CdTe to produce PERC-like CdTe solar cells (CdTe PERC). 
    more » « less
  5. ; ; (, Applied Optics)
    A systematic study was performed with a coupled optoelectronic model to examine the effect of the concentration of sunlight on the efficiencies of CIGS, CZTSSe and AlGaAs thin-film solar cells with a graded-bandgap absorber layer. Efficiencies of 34.6% for CIGS thin-film solar cells and 29.9% for CZTSSe thin-film solar cells are predicted with a concentration of 100 suns, the respective one-sun efficiencies being 27.7% and 21.7%. An efficiency of 36.7% is predicted for AlGaAs thin-film solar cells with a concentration of 60 suns, in comparison to 34.5% one-sun efficiency. Sunlight concentration does not affect the per-sun electron–hole-pair (EHP) generation rate but reduces the per-sun EHP recombination rate either near the front and back faces or in the graded-bandgap regions of the absorber layer, depending upon the semiconductor used for that layer, and this is the primary reason for the improvement in efficiency. Other effects include the enhancement of open-circuit voltage, which can be positively correlated to the higher short-circuit current density. Sunlight concentration can therefore play a significant role in enhancing the efficiency of thin-film solar cells. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email