The mechanical bonding of dissimilar metals though the application of high‐pressure torsion (HPT) processing is developed recently for introducing unique ultrafine‐grained alloy systems involving microstructural heterogeneity leading to excellent mechanical properties. Considering further developments of the processing approach and the produced hybrid materials, the size effect on microstructural evolution and micromechanical responses of the mechanically bonded Al–Mg systems is evaluated. In practice, processing by HPT is conducted at room temperature on the separate Al and Mg disks having 25 mm diameter under 1.0 GPa at 0.4 rpm, and the results are compared with the mechanically bonded Al–Mg system having 10 mm diameter. The Al–Mg disks having 25 mm diameter show a general hardness distribution where low hardness appears around the disk centers, and it increases at the disk peripheries. Nanoindentation measurements demonstrate that there is excellent plasticity at the edges of the Al–Mg system with 25 mm diameter. The Al–Mg system with both 10 and 25 mm diameters show a consistent trend of hardness evolution outlining an exponential increase of hardness with increasing equivalent strain. The results are anticipated to provide a conceptual framework for the development and scale‐up of the HPT‐induced mechanical bonding technique.
An overview of the mechanical bonding of dissimilar bulk engineering metals through high‐pressure torsion (HPT) processing at room temperature is described in this Review. A recently developed procedure of mechanical bonding involves the application of conventional HPT processing to alternately stacked two or more disks of dissimilar metals. A macroscale microstructural evolution involves the concept of making tribomaterials and, for some dissimilar metal combinations, microscale microstructural changes demonstrate the synthesis of metal matrix nanocomposites (MMNCs) through the nucleation of nanoscale intermetallic compounds within the nanostructured metal matrix. Further straining by HPT during mechanical bonding provides an opportunity to introduce limited amorphous phases and a bulk metastable state. The mechanically bonded nanostructured hybrid alloys exhibit an exceptionally high specific strength and an enhanced plasticity. These experimental findings suggest a potential for using mechanical bonding for simply and expeditiously fabricating a wide range of new alloy systems by HPT processing.
- Award ID(s):
- 1810343
- NSF-PAR ID:
- 10130193
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Engineering Materials
- Volume:
- 22
- Issue:
- 4
- ISSN:
- 1438-1656
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
null (Ed.)Processing through the application of high-pressure torsion (HPT) provides significant grain refinement in bulk metals at room temperature. These ultrafine-grained (UFG) materials after HPT generally demonstrate exceptional mechanical properties. Recent reports demonstrated the bulk-state reactions for mechanical bonding of dissimilar lightweight metal disks to synthesize hybrid alloy systems by utilizing conventional HPT processing. Accordingly, the present report provides a comprehensive summary of the recent work on processing of several UFG hybrid alloy systems including Al-Mg and Al-Cu by HPT under 6.0 GPa at room temperature and a special emphasis was placed on understanding the evolution of hardness. This study demonstrates a significant opportunity for the application of HPT for a possible contribution to current enhancements in diffusion bonding, welding and mechanical joining technologies as well as to an introduction of hybrid engineering nanomaterials.more » « less
-
Heterogeneous bonding between metals and ceramics is of significant relevance to a wide range of applications in the fields of industry, defense, and aerospace. Metal/ceramic bonding can be used in various specific part applications such as vacuum tubes, automotive use of ceramic rotors, and rocket igniter bodies. However, the bonding of ceramic to metal has been challenging mainly due to (1) the low wettability of ceramics, on which the adhesion of molten adhesive bonders is limited and (2) the large difference between the coefficients of thermal expansion (CTE) of the two dissimilar bonded materials, which develops significant mechanical stresses at the interface and potentially leads to mechanical failures. Vapor-phase deposition is a widely used thin film processing technique in both academic research laboratories and manufacturing industries. Since vapor phase coatings do not require wettability or hydrophobicity, a uniform and strongly adherent layer is deposited over virtually any substrate, including ceramics. In this presentation, we report on the effect of vapor phase-deposited interfacial metal layers on the mechanical properties of bonding between stainless steel and Zerodur (lithium aluminosilicate-based glass ceramic). Direct-current magnetron sputtering was utilized to deposit various thin interfacial layers containing Ti, Cu, or Sn. In addition, to minimize the unfavorable stress at the bonded interface due to the large CTE difference, a low temperature allow solder, that can be chemically and mechanically activated at temperatures of approximately 200 °C, was used. The solder is made from a composite of Ti-Sn-Ce-In. A custom-built fixture and universal testing machine were used to evaluate the bonding strength in shear, which was monitored in-situ with LabView throughout the measurement. The shear strength of the bonding between stainless steel and Zerodur was systematically characterized as a function of interfacial metal and metal processing temperature during sputter depositions. Maximum shear strength of the bonding of 4.36 MPa was obtained with Cu interfacial layers, compared to 3.53 MPa from Sn and 3.42 MPa from Ti adhesion promoting layers. These bonding strengths are significantly higher than those (~0.05 MPa) of contacts without interfacial reactive thin metals. The fracture surface microstructures are presented as well. It was found that the point of failure, when Cu interfacial layers were used, was between the coated Cu film and alloy bonder. This varied from the Sn and Ti interfacial layers where the main point of failure was between the interfacial film and Zerodur interface. The findings of the effect of thin adhesion promoting metal layers and failure behaviors may be of importance to some metal/ceramic heterogeneous bonding studies that require high bonding strength and low residual stresses at the bonding interface. The authors gratefully acknowledge the financial support of the Improvement of Measurement Standards and Technology for Mechanical Metrology (Grant No. 20011028) by KRISS.more » « less
-
more » « less
Zinc (Zn) alloys, particularly those incorporating magnesium (Mg), have been explored as potential bioabsorbable metals. However, there is a continued need to enhance the corrosion characteristics of Zn-Mg alloys to fulfill the requirements for biodegradable implants. This work involves a corrosion behavior comparison between severe-plastic-deformation (SPD) processed cast Zn-Mg alloys and their hybrid counterparts, having equivalent nominal compositions. The SPD processing technique used was high-pressure torsion (HPT), and the corrosion behavior was studied as a function of the number of turns (1, 5, 15) for the Zn-3Mg (wt.%) alloy and hybrid and as a function of composition (Mg contents of 3, 10, 30 wt.%) for the hybrid after 15 turns. The results indicated that HPT led to multimodal grain size distributions of ultrafine Mg-rich grains containing MgZn2 and Mg2Zn11 nanoscale intermetallics in a matrix of coarser dislocation-free Zn-rich grains. A greater number of turns resulted in greater corrosion resistance because of the formation of the intermetallic phases. The HPT hybrid was more corrosion resistant than its alloy counterpart because it tended to form the intermetallics more readily than the alloy due to the inhomogeneous conditions of the materials before the HPT processing as well as the non-equilibrium conditions imposed during the HPT processing. The HPT hybrids with greater Mg contents were less corrosion resistant because the addition of Mg led to less noble behavior.
-
null (Ed.)The processing of bulk metals through the application of severe plastic deformation (SPD), using procedures such as equal-channel angular pressing (ECAP) and high-pressure torsion (HPT), is now well established for the fabrication of materials with exceptionally small grain sizes, usually in the submicrometer range and often having grain sizes at the nanometer level. These grain sizes cannot be achieved using thermo-mechanical processing or any conventional processing techniques. Recently, these procedures have been further developed to process alternative advanced materials. For example, by stacking separate disks within the HPT facility for the synthesis of bulk nanocrystalline metastable alloys where it is possible to achieve exceptionally high hardness, or by pressing powders or metallic particles in order to obtain new and novel nanocomposites exhibiting unusual properties.more » « less
