Suspensions of soft and highly deformable microgels can be concentrated far more than suspensions of hard colloids, leading to their unusual mechanical properties. Microgels can accommodate compression in suspensions in a variety of ways such as interpenetration, deformation, and shrinking. Previous experiments have offered insightful, but somewhat conflicting, accounts of the behavior of individual microgels in compressed suspensions. We develop a mesoscale computational model to probe the behavior of compressed suspensions consisting of microgels with different architectures at a variety of packing fractions and solvent conditions. We find that microgels predominantly change shape and mildly shrink above random close packing. Interpenetration is only appreciable above space filling, remaining small relative to the mean distance between cross-links. At even higher packing fractions, microgels solely shrink. Remarkably, irrespective of the single-microgel properties, and whether the suspension concentration is changed via changing the particle number density or the swelling state of the particles, which can even result in colloidal gelation, the mechanics of the suspension can be quantified in terms of the single-microgel bulk modulus, which thus emerges as the correct mechanical measure for these type of soft-colloidal suspensions. Our results rationalize the many and varied experimental results, providing insights into the relative importance of effects defining the mechanics of suspensions comprising soft particles.
Capillary assembly is a versatile method for depositing colloidal particles within templates, resulting in nano/microarrays and colloidal superstructures for optical, plasmonic, and sensory applications. Liquid particles (LPs), comprised of oligomerized 3‐(trimethoxysilyl)propyl methacrylate, are herein shown to deposit into patterned cavities via capillary assembly. In contrast to solid colloids, LPs coalesce upon solvent evaporation and assume the geometry of the template. Incorporating small molecules such as dyes followed by LP solidification generates fluorescent polymer microarrays of any geometry. The LP size is inversely proportional to the quantity of deposited material and the convexity of the final polymer array. Cavity filling can be tuned by increasing the assembly temperature. Extraction of the polymerized regions produces solidified particles with faceted shapes including square prisms, trapezoids, and ellipsoids with sizes up to 14 µm that retain the shape of the cavity in which they are initially held. LP deposition thus presents a highly controllable fabrication scheme for geometrically diverse polymer microarrays and anisotropic colloids of any conceivable polygonal shape due to space filling of the template. The extension of capillary assembly to LPs that can be doped with small molecule dyes and analytes invaluably expands the synthetic toolbox for top‐down, scalable, hierarchically engineered materials.
more » « less- NSF-PAR ID:
- 10140200
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Small
- Volume:
- 16
- Issue:
- 16
- ISSN:
- 1613-6810
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Abstract Materials made by directed self‐assembly of colloids can exhibit a rich spectrum of optical phenomena, including photonic bandgaps, coherent scattering, collective plasmonic resonance, and wave guiding. The assembly of colloidal particles with spatial selectivity is critical for studying these phenomena and for practical device fabrication. While there are well‐established techniques for patterning colloidal crystals, these often require multiple steps including the fabrication of a physical template for masking, etching, stamping, or directing dewetting. Here, the direct‐writing of colloidal suspensions is presented as a technique for fabrication of iridescent colloidal crystals in arbitrary 2D patterns. Leveraging the principles of convective assembly, the process can be optimized for high writing speeds (≈600 µm s−1) at mild process temperature (30 °C) while maintaining long‐range (cm‐scale) order in the colloidal crystals. The crystals exhibit structural color by grating diffraction, and analysis of diffraction allows particle size, relative grain size, and grain orientation to be deduced. The effect of write trajectory on particle ordering is discussed and insights for developing 3D printing techniques for colloidal crystals via layer‐wise printing and sintering are provided.
-
Selective deposition of hybrid and inorganic materials inside nanostructures could enable major nanotechnological advances. However, inserting ready-made composites inside nanocavities may be difficult, and therefore, stepwise approaches are needed. In this paper, a poly(ethyl acrylate) template is grown selectively inside cavities via condensation-controlled toposelective vapor deposition, and the polymer is then hybridized by alumina, titania, or zinc oxide. The hybridization is carried out by infiltrating the polymer with a vapor-phase metalorganic precursor and water vapor either via a short-pulse (atomic layer deposition, ALD) or a long-pulse (vapor phase infiltration, VPI) sequence. When the polymer-MO x hybrid material is calcined at 450 °C in air, an inorganic phase is left as the residue. Various suspected confinement effects are discussed. The infiltration of inorganic materials is reduced in deeper layers of the cavity-grown polymer and is dependent on the cavity geometry. The structure of the inorganic deposition after calcination varies from scattered particles and their aggregates to cavity-capping films or cavity-filling low-density porous deposition, and the inorganic deposition is often anisotropically cracked. A large part of the infiltration is achieved already during the short-pulse experiments with a commercial ALD reactor. Furthermore, the infiltrated polymer is more resistant to dissolution in acetone whereas the inorganic component can still be heavily affected by phosphoric acid.more » « less
-
more » « less
Abstract It is challenging to find a conventional nanofabrication technique that can consistently produce soft polymeric matter of high surface area and nanoscale morphology in a way that is scalable, versatile, and easily tunable. Here, the capabilities of a universal method for fabricating diverse nano‐ and micro‐scale morphologies based on polymer precipitation templated by the fluid streamlines in multiphasic flow are explored. It is shown that while the procedure is operationally simple, various combinations of its intertwined mechanisms can controllably and reproducibly lead to the formation of an extraordinary wide range of colloidal morphologies. By systematically investigating the process conditions, 12 distinct classes of polymer micro‐ and nano‐structures including particles, rods, ribbons, nanosheets, and soft dendritic colloids (dendricolloids) are identified. The outcomes are interpreted by delineating the physical processes into three stages: hydrodynamic shear, capillary and mechanical breakup, and polymer precipitation rate. The insights into the underlying fundamental mechanisms provide guidance toward developing a versatile and scalable nanofabrication platform. It is verified that the liquid shear‐based technique is versatile and works well with many chemically diverse polymers and biopolymers, showing potential as a universal tool for simple and scalable nanofabrication of many morphologically distinct soft matter classes.
-
more » « less
Abstract The dynamic manipulation of colloidal particle shape offers a novel design mechanism for the creation of advanced responsive materials. To this end, we introduce a versatile new strategy for shape control of anisotropic polymeric colloidal particles. The concept utilizes temperature‐sensitive absorption of a suitable solvent from a binary mixture. Specifically, increasing the temperature in the vicinity of the demixing transition of a binary mixture causes more solvent to be absorbed into the polymeric colloidal particle, which, in turn, lowers the glass transition temperature of the polymer inside the particle, with a concomitant decrease in viscosity. The balance between the internal viscosity and surface tension of the particle is thus disrupted, and the anisotropic shape of the particle shifts to become more spherical. Subsequent rapid temperature quenching can halt the process, leaving the particle with an intermediate anisotropy. The resultant shape anisotropy control provides new routes for studies of the phase transitions of anisotropic colloids and enables the fabrication of unique particles for materials applications.
