Solid-state single-ion conducting polymer electrolytes have drawn considerable interest for secondary lithium batteries due to their potential for high electrochemical stability and safety, but applications are limited by their low ionic conductivities. Specifically, poly(ethylene oxide) (PEO) based electrolytes have the highest reported Li + conductivities for these materials; however, their potential is limited due to the ion transport mechanism being coupled to segmental relaxations of the cation solvating polymer chain. To investigate the potential of single-ion conducting polymer electrolytes lacking polar matrices, we synthesized three para -polyphenylene-based, side-chain polymer electrolytes with various pendent anion chemistries (–SO 3 − , –PSI − , and –TFSI − ) with differing binding affinities to Li + . Compared with the previously reported lithium poly(4-styrenesulfonyl(trifluoromethylsulfonyl)imide) (LiPSTFSI), the side-chain polymers showed at least 3 orders of magnitude higher conductivity with the same –TFSI − anion (6.7 × 10 −6 S cm −1 compared with 1.2 × 10 −10 S cm −1 at 150 °C). We found that the side-chain electrolyte showed a dielectric relaxation dominated transport mechanism through use of dielectric spectroscopy analysis. The conductivity is highly dependent on the charge delocalization and size of the pendent anion, which provides a pathway forward for the engineering of polymeric ion conductors for electrochemical applications.
more »
« less
Comparison of Single-Ion Conducting Polymer Gel Electrolytes for Sodium, Potassium, and Calcium Batteries: Influence of Polymer Chemistry, Cation Identity, Charge Density, and Solvent on Conductivity
From the standpoint of material diversification and sustainability, the development of so-called “beyond lithium-ion” battery chemistries is important for the future of energy storage. Na, K, and Ca are promising as the basis for battery chemistries in that these elements are highly abundant. Here, a series of single-ion conducting polymer electrolytes (SIPEs) for Na, K, and Ca batteries are synthesized and investigated. The two classes of metal cation neutralized SIPEs compared are crosslinked poly(ethylene glycol) dimethacrylate-x-styrene sulfonate (PEGDMA-SS) and poly(tetrahydrofuran) diacrylate-x-4-styrenesulfonyl (trifluoromethylsulfonyl)imide (PTHFDA-STFSI); three cation types, three charge densities, and four swelling states are examined. The impact on conductivity of all of these parameters is studied, and in conjunction with small angle X-ray scattering (SAXS), it is found that promoting ion dissociation and preventing the formation of dense ionic aggregates facilitates ion transport. These results indicate many of the lessons learned from the Li SIPE literature can be translated to beyond Li chemistries. At 25 °C, the best performing Na/K and Ca exchanged polymers yield active cation conductivity on the order of 10−4 S/cm and 10−6 S/cm, respectively, for ethylene carbonate:propylene carbonate gelled SIPEs, and 10−5 S/cm and 10−7 S/cm, respectively, for glyme gelled SIPEs.
more »
« less
- Award ID(s):
- 1706370
- NSF-PAR ID:
- 10148499
- Date Published:
- Journal Name:
- Batteries
- Volume:
- 6
- Issue:
- 1
- ISSN:
- 2313-0105
- Page Range / eLocation ID:
- 11
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Maximizing ion conduction in single-ion-conducting ionomers is essential for their application in energy-related technologies such as Li-ion batteries. Understanding the anion chemical composition impacts on ion conduction offers new perspectives to maximize ion transport, since the current approach of lowering T g has apparently reached a limit (lowest T g ∼ 190 K, highest conductivity ∼10 −5 –10 −4 S cm −1 ). Here, a series of random ionomers are synthesized by copolymerizing poly(ethylene glycol)methacrylate with either sulfonylimide lithium methacrylate (MTLi) or sulfonate lithium methacrylate (MSLi) using reversible addition–fragmentation chain transfer (RAFT) polymerization. Li-Ion conduction and self-diffusion coefficients ( D Li + ) of the ionomers are characterized with dielectric relaxation spectroscopy (DRS) and pulsed-field-gradient (PFG) NMR diffusometry, respectively. Increasing ion content decreases the Li-ion conductivity and D Li + , as expected from the increased T g . Moreover, a considerably lower ionic conductivity and D Li + are observed for MSLi compared to MTLi at constant ion content and T g / T . As revealed from X-ray scattering, strong ion aggregation in MSLi results in much lower conductivity and D Li + compared with less aggregated MTLi based on the more delocalized sulfonylimide anion. These results emphasize the detrimental and molecularly specific role of ion aggregation in Li-ion conductivity, and highlight the necessity for minimizing ion aggregation via the rational choice of anion chemical composition.more » « less
-
more » « less
Abstract Single‐ion conducting polymer electrolytes are of interest for use with advanced battery electrodes such as lithium metal, but achieving sufficiently high conductivity has been challenging. In this work, a model system containing charged sites that are precisely spaced along the polymer backbone is explored. Precision sulfonated poly(4‐phenylcyclopentene) lithium salt (
p 5PhS‐Li) with a high degree of sulfonation (> 90%) is synthesized and blended with poly(ethylene oxide) (PEO) to investigate the thermodynamic and transport properties. Melting point depression is measured via differential scanning calorimetry, ionic conductivity,κ , is determined using electrochemical impedance spectroscopy, and the fraction of current carried by Li+is estimated based on steady‐state current measurements. In conjunction with a density measurement, melting point depression is used to find an effective Flory–Huggins interaction parameter,χ eff = − 0.21, suggesting miscibility of the blend.κ spans a large range from 2 × 10−11to 2 × 10−7S cm−1over the composition and temperature range investigated. The fraction of charge carried by lithium ions also spans a significant range from 0.12 in majority PEO blend to 0.98 in majorityp 5PhS‐Li blend. This study addresses several limitations of sulfonated polystyrene and opens up the possibility of precisely controlling the spacing of other anion types. -
more » « less
Abstract Solid polymer electrolytes (SPEs) promise to improve the safety and performance of lithium ion batteries (LIBs). However, the low ionic conductivity and transference number of conventional poly(ethylene oxide) (PEO)‐based SPEs preclude their widespread implementation. Herein, crosslinked poly(tetrahydrofuran) (xPTHF) is introduced as a promising polymer matrix for “beyond PEO” SPEs. The crosslinking procedure creates thermally stable, mechanically robust membranes for use in LIBs. Molecular dynamics and density functional theory (DFT) simulations accompanied by7Li NMR measurements show that the lower spatial concentration of oxygen atoms in the xPTHF backbone leads to loosened O–Li+coordination. This weakened interaction enhances ion transport; xPTHF has a high lithium transference number of 0.53 and higher lithium conductivity than a xPEO SPE of the same length at room temperature. It is demonstrated that organic additives further weaken the O–Li+interaction, enabling room temperature ionic conductivity of 1.2 × 10−4S cm−1with 18 wt%
N,N ‐dimethylformamide in xPTHF. In a solid‐state LIB application, neat xPTHF SPEs cycle with near theoretical capacity for 100 cycles at 70 °C, with rate capability up to 1 C. The plasticized xPTHF SPEs operate at room temperature while maintaining respectable rate capability and capacity. The novel PTHF system demonstrated here represents an exciting platform for future studies involving SPEs. -
more » « less
Abstract Polyphosphonates, a class of polymers with the generic formula –[P(R)(X)–OR'O]n–, exhibit a high degree of modularity due to the range of R, R', and X groups that can be incorporated. As such, these polymers may be designed with a polyethylene oxide (PEO) backbone (R' group) and employed as solid polymer electrolytes (SPEs). Two PEO‐containing polyphosphonate analogs (R = Ph; X = S or Se) were doped with LiPF6and their conductivities were measured. Conductivities were similar (X = S) to or exceeding (X = Se) those of standard PEO systems (just below 10−4S/cm at 100°C). Binding models for Li+were generated using31P{1H}NMR titration experiments. Binding of Li+by these polyphosphonates followed a positive cooperativity model, and varying the X group (S or Se) affected the observed cooperativity (Hill coefficient = 1.73 and 4.16, respectively). The presence of Se also leads to an increase in conductivity as temperature is raised above the Tg, which is likely an effect of reduced Columbic interactions. Because of their modularity and ease with which cation binding can be evaluated using31P{1H} NMR titration experiments, polyphosphonates offer a unique approach for the modification of Li+ion battery technology.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/batteries6010011
