Full-waveform inversion (FWI) methods rely on accurate numerical simulation of wave propagation in the analysed medium. Acoustic or elastic wave equations are often used to model seismic wave propagation. These types of simulations do not account for intrinsic attenuation effects due to material anelasticity, and thus correction techniques have been utilized in practice to partially compensate the anelasticity. These techniques often only consider the waveform amplitude correction based on averaging of overall amplitude response over the entire data set, and ignore the phase correction. Viscoelastic wave equations account for the anelastic response in both waveform amplitude and phase, and are therefore a more suitable alternative. In this study, we present a novel 3-D Gauss–Newton viscoelastic FWI (3-D GN-VFWI) method. To address the main challenge of the Gauss–Newton optimization, we develop formulas to compute the Jacobian efficiently by the convolution of virtual sources and backward wavefields. The virtual sources are obtained by directly differentiating the viscoelastic wave equations with respect to model parameters. In order to resolve complex 3-D structures with reasonable computational effort, a homogeneous attenuation (Q factor) is used throughout the analysis to model the anelastic effects. Synthetic and field experiments are performed to demonstrate the utility of the method. The synthetic results clearly demonstrate the ability of the method in characterizing a challenging velocity profile, including voids and reverse velocity layers. The field experimental results show that method successfully characterizes the complex substructure with two voids and undulating limestone bedrock, which are confirmed by invasive tests. Compared to 3-D elastic FWI results, the presented viscoelastic method produces more accurate results regarding depths of the voids and bedrock. This study suggests that the improvement of imaging accuracy would warrant the widespread use of viscoelastic wave equations in FWI problems. To our best knowledge, this is the first reported study on 3-D GN-VFWI at any scale. This study provides the new theory and formulation for the use of Gauss–Newton optimization on the 3-D viscoelastic problem.
- Award ID(s):
- 1850696
- NSF-PAR ID:
- 10181234
- Date Published:
- Journal Name:
- GEOPHYSICS
- Volume:
- 85
- Issue:
- 5
- ISSN:
- 0016-8033
- Page Range / eLocation ID:
- B147 to B157
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
SUMMARY -
more » « less
Abstract To complement velocity distributions, seismic attenuation provides additional important information on fluid properties of hydrocarbon reservoirs in exploration seismology, as well as temperature distributions, partial melting, and water content within the crust and mantle in earthquake seismology. Full waveform inversion (FWI), as one of the state‐of‐the‐art seismic imaging techniques, can produce high‐resolution constraints for subsurface (an)elastic parameters by minimizing the difference between observed and predicted seismograms. Traditional waveform inversion for attenuation is commonly based on the standard‐linear‐solid (SLS) wave equation, in which case the quality factor (
Q ) has to be converted to stress and strain relaxation times. When using multiple attenuation mechanisms in the SLS method, it is difficult to directly estimate these relaxation time parameters. Based on a time domain complex‐valued viscoacoustic wave equation, we present an FWI framework for simultaneously estimating subsurfaceP wave velocity and attenuation distributions. BecauseQ is explicitly incorporated into the viscoacoustic wave equation, we directly deriveP wave velocity andQ sensitivity kernels using the adjoint‐state method and simultaneously estimate their subsurface distributions. By analyzing the Gauss‐Newton Hessian, we observe strong interparameter crosstalk, especially the leakage from velocity toQ . We approximate the Hessian inverse using a preconditioned L‐BFGS method in viscoacoustic FWI, which enables us to successfully reduce interparameter crosstalk and produce accurate velocity and attenuation models. Numerical examples demonstrate the feasibility and robustness of the proposed method for simultaneously mapping complex velocity andQ distributions in the subsurface. -
more » « less
SUMMARY Improving the resolution of seismic anelastic models is critical for a better understanding of the Earth’s subsurface structure and dynamics. Seismic attenuation plays a crucial role in estimating water content, partial melting and temperature variations in the Earth’s crust and mantle. However, compared to seismic wave-speed models, seismic attenuation tomography models tend to be less resolved. This is due to the complexity of amplitude measurements and the challenge of isolating the effect of attenuation in the data from other parameters. Physical dispersion caused by attenuation also affects seismic wave speeds, and neglecting scattering/defocusing effects in classical anelastic models can lead to biased results. To overcome these challenges, it is essential to account for the full 3-D complexity of seismic wave propagation. Although various synthetic tests have been conducted to validate anelastic full-waveform inversion (FWI), there is still a lack of understanding regarding the trade-off between elastic and anelastic parameters, as well as the variable influence of different parameter classes on the data. In this context, we present a synthetic study to explore different strategies for global anelastic inversions.
To assess the resolution and sensitivity for different misfit functions, we first perform mono-parameter inversions by inverting only for attenuation. Then, to study trade-offs between parameters and resolution, we test two different inversion strategies (simultaneous and sequential) to jointly constrain the elastic and anelastic parameters. We found that a sequential inversion strategy performs better for imaging attenuation than a simultaneous inversion. We also demonstrate the dominance of seismic wave speeds over attenuation, underscoring the importance of determining a good approximation of the Hessian matrix and suitable damping factors for each parameter class.
-
more » « less
SUMMARY Non-invasive subsurface imaging using full waveform inversion (FWI) has the potential to fundamentally change near-surface (<30 m) site characterization by enabling the recovery of high-resolution (metre-scale) 2-D/3-D maps of subsurface elastic material properties. Yet, FWI results are quite sensitive to their starting model due to their dependence on local-search optimization techniques and inversion non-uniqueness. Starting model dependence is particularly problematic for near-surface FWI due to the complexity of the recorded seismic wavefield (e.g. dominant surface waves intermixed with body waves) and the potential for significant spatial variability over short distances. In response, convolutional neural networks (CNNs) are investigated as a potential tool for developing starting models for near-surface 2-D elastic FWI. Specifically, 100 000 subsurface models were generated to be representative of a classic near-surface geophysics problem; namely, imaging a two-layer, undulating, soil-over-bedrock interface. A CNN has been developed from these synthetic models that is capable of transforming an experimental wavefield acquired using a seismic source located at the centre of a linear array of 24 closely spaced surface sensors directly into a robust starting model for FWI. The CNN approach was able to produce 2-D starting models with seismic image misfits that were significantly less than the misfits from other common starting model approaches, and in many cases even less than the misfits obtained by FWI with inferior starting models. The ability of the CNN to generalize outside its two-layered training set was assessed using a more complex, three-layered, soil-over-bedrock formation. While the predictive ability of the CNN was slightly reduced for this more complex case, it was still able to achieve seismic image and waveform misfits that were comparable to other commonly used starting models, despite not being trained on any three-layered models. As such, CNNs show great potential as tools for rapidly developing robust, site-specific starting models for near-surface elastic FWI.
-
more » « less
SUMMARY The spectral element method is currently the method of choice for computing accurate synthetic seismic wavefields in realistic 3-D earth models at the global scale. However, it requires significantly more computational time, compared to normal mode-based approximate methods. Source stacking, whereby multiple earthquake sources are aligned on their origin time and simultaneously triggered, can reduce the computational costs by several orders of magnitude. We present the results of synthetic tests performed on a realistic radially anisotropic 3-D model, slightly modified from model SEMUCB-WM1 with three component synthetic waveform ‘data’ for a duration of 10 000 s, and filtered at periods longer than 60 s, for a set of 273 events and 515 stations. We consider two definitions of the misfit function, one based on the stacked records at individual stations and another based on station-pair cross-correlations of the stacked records. The inverse step is performed using a Gauss–Newton approach where the gradient and Hessian are computed using normal mode perturbation theory. We investigate the retrieval of radially anisotropic long wavelength structure in the upper mantle in the depth range 100–800 km, after fixing the crust and uppermost mantle structure constrained by fundamental mode Love and Rayleigh wave dispersion data. The results show good performance using both definitions of the misfit function, even in the presence of realistic noise, with degraded amplitudes of lateral variations in the anisotropic parameter ξ. Interestingly, we show that we can retrieve the long wavelength structure in the upper mantle, when considering one or the other of three portions of the cross-correlation time series, corresponding to where we expect the energy from surface wave overtone, fundamental mode or a mixture of the two to be dominant, respectively. We also considered the issue of missing data, by randomly removing a successively larger proportion of the available synthetic data. We replace the missing data by synthetics computed in the current 3-D model using normal mode perturbation theory. The inversion results degrade with the proportion of missing data, especially for ξ, and we find that a data availability of 45 per cent or more leads to acceptable results. We also present a strategy for grouping events and stations to minimize the number of missing data in each group. This leads to an increased number of computations but can be significantly more efficient than conventional single-event-at-a-time inversion. We apply the grouping strategy to a real picking scenario, and show promising resolution capability despite the use of fewer waveforms and uneven ray path distribution. Source stacking approach can be used to rapidly obtain a starting 3-D model for more conventional full-waveform inversion at higher resolution, and to investigate assumptions made in the inversion, such as trade-offs between isotropic, anisotropic or anelastic structure, different model parametrizations or how crustal structure is accounted for.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1190/GEO2019-0490.1
