An official website of the United States government
Although graphene is well known for super-lubricity on its basal plane, friction at its step edge is not well understood and contradictory friction behaviors have been reported. In this study, friction of mono-layer thick graphene step edges was studied using atomic force microscopy (AFM) with a Si tip in dry nitrogen atmosphere. It is found that, when the tip slides over a ‘buried’ graphene step edge, there is a resistive force during the step-up motion and an assistive force during the step-down motion due to the topographic height change. The magnitude of these two forces is small and the same in both step-up and step-down motions. As for the ‘exposed’ graphene step edge, friction increases in magnitude and exhibits more complicated behaviors. During the step-down motion of the tip over the exposed step edge, both resistive and assistive components can be detected in the lateral force signal of AFM if the scan resolution is sufficiently high. The resistive component is attributed to chemical interactions between the functional groups at the tip and step-edge surfaces, and the assistive component is due to the topographic effect, same as the case of buried step edge. If a blunt tip is used, the distinct effects of these two components become more prominent. In the step-up scan direction, the blunt tip appears to have two separate topographic effects elastic deformation of the contact region at the bottom of the tip due to the substrate height change at the step edge and tilting of the tip while the vertical position of the cantilever (the end of the tip) ascends from the lower terrace to the upper terrace. The high-resolution measurement of friction behaviors at graphene step edges will further enrich understanding of interfacial friction behaviors on graphene-covered surfaces.
more »
« less
Effect of Atomic Corrugation on Adhesion and Friction: A Model Study with Graphene Step Edges
This Letter reports that the atomic corrugation of the surface can affect nanoscale interfacial adhesion and friction differently. Both atomic force microscopy (AFM) and molecular dynamics (MD) simulations showed that the adhesion force needed to separate a silica tip from a graphene step edge increases as the side wall of the tip approaches the step edge when the tip is on the lower terrace and decreases as the tip ascends or descends the step edge. However, the friction force measured with the same AFM tip moving across the step edge does not positively correlate with the measured adhesion, which implies that the conventional contact mechanics approach of correlating interfacial adhesion and friction could be invalid for surfaces with atomic-scale features. The chemical and physical origins for the observed discrepancy between adhesion and friction at the atomic step edge are discussed.
more »
« less
- Award ID(s):
- 1727571
- PAR ID:
- 10182965
- Date Published:
- Journal Name:
- The journal of physical chemistry letters
- Volume:
- 10
- ISSN:
- 1948-7185
- Page Range / eLocation ID:
- 6455–6461
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Atomic force microscopy (AFM) is typically used for analysis of relatively flat surfaces with topographic features smaller than the height of the AFM tip. On flat surfaces, it is relatively easy to find the object of interest and deconvolute imaging artifacts resulting from the finite size of the AFM tip. In contrast, AFM imaging of three-dimensional objects much larger than the AFM tip height is rarely attempted although it could provide topographic information that is not readily available from two-dimensional imaging, such as scanning electron microscopy. In this paper, we report AFM measurements of a vertically-mounted razor blade, which is taller and sharper than the AFM tip. In this case, the AFM height data, except for the data collected around the cutting edge of the blade, reflect the shape of the AFM tip. The height data around the apex area are effectively the convolution of the AFM tip and the blade cutting edge. Based on computer simulations mimicking an AFM tip scanning across a round sample, a simple algorithm is proposed to deconvolute the AFM height data of an object taller and sharper than the AFM tip and estimate its effective curvature.more » « less
-
null (Ed.)This study is aimed to evaluate the effects of coated surgical needles with composite polymers such as polydopamine (PDA), polytetrafluoroethylene (PTFE), and carbon. The coated needle’s lubrication properties were measured using 3 DOF force sensors and 3D robot system by the repetitive insertion in soft tissue materials. Needle durability is a measure of needle sharpness after repeated passage through high stiffness tissue materials. The composite coatings were shown to reduce the insertion force by ∼49% and retraction forces by ∼46% when tested using a bovine kidney. The surface roughness and the lateral friction force of the needle are measured using the Atomic Force Microscope (AFM). The adhesion energy of the different coating on the needle will be measured using a nano-scratch method.more » « less
-
Abstract Atomic force microscope (AFM)-based nanolithography is a cost-effective nanopatterning technique that can fabricate nanostructures with arbitrary shapes. However, existing AFM-based nanopatterning approaches have limitations in the patterning resolution and efficiency. Minimum feature size and machining performance in the mechanical force-induced nanofabrication process are limited by the radius and sharpness of the AFM tip. Electric-field-assisted atomic force microscope (E-AFM) nanolithography can fabricate nanopatterns with features smaller than the tip radius, but it is very challenging to find the appropriate input parameter window. The tip bias range in E-AFM process is typically very small and varies for each AFM tip due to the variations in tip geometry, tip end diameter, and tip conductive coating thickness. This paper demonstrates a novel electric-field and mechanical vibration-assisted AFM-based nanofabrication approach, which enables high-resolution (sub-10 nm toward sub-5 nm) and high-efficiency nanopatterning processes. The integration of in-plane vibration with the electric field increases the patterning speed, broadens the selectable ranges of applied voltages, and reduces the minimum tip bias required for nanopatterning as compared with E-AFM process, which significantly increases the versatility and capability of AFM-based nanopatterning and effectively avoids the tip damage.more » « less
-
Although earthquakes are one of the most notorious natural disasters, a full understanding of the underlying mechanisms is still lacking. Here, nanoscale friction measurements were performed by atomic force microscopy (AFM) on calcite single crystals with an oxidized silicon tip to investigate the influence of roughness, contact aging, and dry vs. aqueous environment. In dry environments, smooth and rough calcite surfaces yielding single- and multiasperity contacts, respectively, exhibit velocity-weakening ( β D ln V ) or neutral friction at slow sliding velocities and velocity-strengthening friction ( α D ln V ) at higher velocities, while the transition shifts to slower velocities with an increase in roughness. The origin of the velocity-weakening friction is determined to be contact aging resulting from atomic attrition of the crystalline surface. Friction measurements in aqueous environment show evidence of pressure solution at sufficiently slow sliding velocities, which not only significantly reduces friction on single-and multiasperity contacts but also, eliminates atomic attrition and thereby, velocity-weakening friction. Importantly, the friction scaling law evolves from logarithmic ( β D ln V ) into linear ( α P S V ), deviating from commonly accepted rate-and-state friction (RSF) laws; this behavior extends over a wider range of velocities with higher roughness. Above a transition velocity, the scaling law remains logarithmic ( α W ln V ). The friction rate parameters α D , β D , α P S , and α W decrease with load and depend on roughness in a nonmonotonic fashion, like the adhesion, suggesting the relevance of the contact area. The results also reveal that parameters and memory distance differ in dry and aqueous environments, with implications for the understanding of mechanisms underlying RSF laws and fault stability.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1021/acs.jpclett.9b02501
