skip to main content

Explore Research Products in the NSF-PAR

Title: Nanostructure and Fracture Behavior of Carbon Nanofiber-Reinforced Cement Using Nanoscale Depth-Sensing Methods
In recent years, carbon nanofibers have been investigated as a suitable reinforcement for cementitious composites to yield novel multifunctional materials with improved mechanical, electrical, magnetic, and self-sensing behavior. Despite several studies, the interactions between carbon nanofibers and Portland cement hydration products are not fully understood, with significant implications for the mechanical response and the durability at the macroscopic lengthscale. Thus, the research objective is to investigate the influence of carbon nanofibers on the nanostructure and on the distribution of hydration products within Portland cement paste. Portland cement w/c = 0.44 specimens reinforced with 0.0 wt%, 0.1 wt%, and 0.5 wt% CNF by mass fraction of cement are cast using a novel synthesis procedure. A uniform dispersion of carbon nanofibers (CNF) via a multi-step approach: after pre-dispersing carbon nanofibers using ultrasonic energy, the carbon nanofibers are further dispersed using un-hydrated cement particles in high shear mixing and mechanical stirring steps. High-resolution scanning electron microscopy analysis shows that carbon nanofibers fill nanopores and connect calcium–silicate hydrates (C–S–H) grains. Grid nano-indentation testing shows that Carbon nanofibers influence the probability distribution function of the local packing density by inducing a shift towards higher values, η = 0.76–0.93. Statistical deconvolution analysis shows that carbon nanofibers result in an increase in the fraction of high-density C–S–H by 6.7% from plain cement to cement + 0.1 wt% CNF and by 10.7% from plain cement to cement + 0.5 wt% CNF. Moreover, CNF lead to an increase in the C–S–H gel porosity and a decrease in both the capillary porosity and the total porosity. Based on scratch testing, adding 0.1 wt% CNF yields a 4.5% increase in fracture toughness and adding 0.5 wt% CNF yields a 7.6% increase in fracture toughness. Finally, micromechanical modelling predicts an increase of respectively 5.97% and 21.78% in the average Young’s modulus following CNF modification at 0.1 wt% CNF and 0.5 wt% CNF levels.  more » « less
Award ID(s):
1829101
NSF-PAR ID:
10197992
Author(s) / Creator(s):
Date Published:
Journal Name:
Materials
Volume:
13
Issue:
17
ISSN:
1996-1944
Page Range / eLocation ID:
3837
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ( , Cement and concrete research)
    null (Ed.)
    We elucidate the mechanisms by which multi-walled carbon nanotubes (MWCNTs) influence the microstructure, fracture behavior, and hydration of cement paste. We disperse MWCNTs using a multi-step approach that involves high-energy pre-dispersion using ultrasonic energy followed by low-energy dispersion using un-hydrated cement particles. In turn, the low-energy dispersion step involves high-shear mixing and mechanical stirring. High-resolution environmental scanning electron microscopy of cement+0.2 wt% MWCNT, cement+0.5 wt% MWNCT, and of cement+1 wt% MWCNT show that MWCNTs bridge air voids, thereby refining the pore size and strengthening the C-S-H matrix. The fracture toughness increased by 9.38% with the addition of 0.2 wt% multi-walled carbon nanotubes, and by 14.06% with the addition of 0.5 wt% multi-walled carbon nanotubes and ligament bridging was the dominant toughening mechanism. Moreover, for all reinforcement levels, MWCNTs induced a conversion of low-density C-S-H into high-density C-S-H along with a drastic drop in the capillary porosity: adding 0.1–0.5 wt% MWCNT resulted in a 200% increase in the volume fraction of high-density C-S-H. Thus, our experiments show that MWCNT enhances the mechanical properties and transport properties by: (i) promoting high-density C-S-H formation, (ii) promoting calcium hydroxide formation, (iii) filling microscopic air voids, (iv) reducing the capillary porosity, (v) increasing the fraction of small gel pores (1.2–2 nm in size), and (vi) by bridging microcracks. 
    more » « less
  2. ( , Philosophical transactions of the Royal Society of London)
    null (Ed.)
    Cement is the most widely consumed material globally, with the cement industry accounting for 8% of human-caused greenhouse gas emissions. Aiming for cement composites with a reduced carbon footprint, this study investigates the potential of nanomaterials to improve mechanical characteristics. An important question is to increase the fraction of carbon-based nanomaterials within cement matrices while controlling the microstructure and enhancing the mechanical performance. Specifically, this study investigates the fracture response of Portland cement reinforced with 1D and 2D carbon-based nanomaterials, such as carbon nanofibers, multiwalled carbon nanotubes, helical carbon nanotubes, and graphene oxide nanoplatelets. Novel processing routes are shown to incorporate 0.1–0.5 wt% of nanomaterials into cement using a quadratic distribution of ultrasonic energy. Scratch testing is used to probe the fracture response by pushing a sphero-conical probe against the surface of the material under a linearly increasing vertical force. Fracture toughness is then computed using a nonlinear fracture mechanics model. Nanomaterials are shown to bridge nanoscale air voids, leading to pore refinement, and a decrease in the porosity and the water absorption. An improvement in fracture toughness is observed in cement nanocomposites, with a positive correlation between the fracture toughness and the mass fraction of nanofiller for graphene-reinforced cement. Moreover, for graphene-reinforced cement, the fracture toughness values are in the range of 0.701 to 0.717 MPa.sqrt(m). Thus, this study illustrates the potential of nanomaterials to toughen cement while improving the microstructure and water resistance properties. 
    more » « less
  3. ( , Journal of materials science)
    We investigate the mechanisms by which titanium dioxide nano-particles (nano-TiO2) interact with cement hydration products. To this end, we synthesize nanomodified cement samples with 1 wt% and 5 wt% of TiO2. We investigate the physical properties using depth-sensing based methods such as statistical nano-indentation and microscopic scratch testing. Fourier transform infrared spectroscopy yields the chemistry, whereas micromechanics modeling provides insights into the nanostructure. The macroscopic plane strain modulus increases by 16% and 83%, respectively, and the macroscopic indentation hardness increases by 37% and 40%, respectively. The fracture toughness rises by 3% and 11%, respectively. Environmental scanning electron microscopy reveals a 30% reduction in crack width for TiO2 cement nanocomposites compared to plain cement. Meanwhile, Fourier transform infrared spectroscopy and statistical deconvolution show an increase in the fraction of high-density calcium silicate hydrates (by 22% and 12% respectively), and in the fraction of calcium hydroxide (by 101% and 251% respectively). Within the framework of the colloidal and granular models of C-S-H, the increase in stiffness and strength after nano-TiO2 modification of cement paste is due to the closely-packed structure and the high atomic coordination number of high-density C-S-H. Similarly, due to the high dimensional stability of high-density C-S-H and calcium hydroxide, our results explain the reported improvements in drying shrinkage and creep properties following cement modification with nano-TiO2. 
    more » « less
  4. ; ; ; ( , Mechanics Research Communications)
    Novel multifunctional construction materials are needed to promote resilient infrastructure in the face of climate change and extreme weather. Nanostructured materials such as geopolymer reinforced with carbon-based nanomaterials are a promising way to reach that goal. In recent years, several studies have investigated the influence of nanomaterials on the physical properties of geopolymer composites such as compressive strength and fracture toughness. Yet, a fundamental understanding of the influence of nanomaterials on the nanoscale and micron-scale structure has been elusive so far. Our research objective is to understand how multiwalled carbon nanotubes (MWCNT) can help tailor the microstructure of geopolymers to yield architected multifunctional nanocomposites. We synthesized geopolymer nanocomposites reinforced with 50-nm thick multiwalled carbon nanotubes with mass fractions in the range of 0.1 wt%, 0.2 wt%, and 0.5 wt%. Our major finding is that MWCNTs act as hard templates that promote geopolymer formation via self-assembly. Geopolymer nanoparticle growth is observed along the walls of MWCNTs. A refinement in grain size is observed: increasing the fraction of MWCNTs by 0.5 wt% leads to a reduction in grain size by 54%. Similarly, increasing the mass fraction of MWCNTs leads to a densification of the geopolymer matrix as demonstrated by the Fourier transform infrared spectroscopy results and the statistical deconvolution analysis. Mercury intrusion porosimetry shows a nanoscale tailoring of the pore size distribution: a 26% decrease in porosity is observed as the fraction of MWCNTs is increased to 0.5 wt%. As a result of these nanoscale structural changes, a greater resistance to long-term deformation is observed for MWCNT-reinforced geopolymers, as the creep modulus increases both locally and macroscopically. At the macroscopic level, a 42% increase in the macroscopic logarithmic creep modulus is observed as the fraction of MWCNTs is increased to 0.5 wt%. These findings and the supporting methodology are important to understand how to manipulate matter below 100 nm. This research also paves the way for the design of resilient infrastructure materials with tailored microstructure and mechanical properties. 
    more » « less
  5. ( , International Journal of Ceramic Engineering & Science)
    Abstract

    We investigate the fracture response of metakaolin‐based geopolymer reinforced with 0.1 wt%, 0.2 wt%, and 0.5 wt% carbon nanofibers. We measure the elastoplastic response using microindentation tests. We note an increase in indentation modulus of 5%, 13%, and 21%, and an increase in indentation hardness of 9%, 18%, and 25%, respectively. We measure the fracture energy using cutting‐edge microscopic fracture tests. In our tests, a sphero‐conical diamond indenter pushes across the specimen's surface under a prescribed vertical force. We analyze the recorded penetration depth and horizontal force using nonlinear fracture mechanics and extract the fracture parameters. We find that carbon nanofibers enhance fracture resistance. The fracture toughness increases by, respectively, 38%, 40%, and 45%; meanwhile, the fracture energy increases by, respectively, 83%, 72%, and 74%. We find that carbon nanofibers lead to a densification of the microstructure. Moreover, we observe crack‐bridging mechanisms in geopolymer nanocomposites. This study is important to pave the way for novel enhanced‐performance and multifunctional structural materials.

     
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email