An official website of the United States government
Abstract Nanograined metals have the merit of high strength, but usually suffer from low work hardening capacity and poor thermal stability, causing premature failure and limiting their practical utilities. Here we report a “nanodispersion-in-nanograins” strategy to simultaneously strengthen and stabilize nanocrystalline metals such as copper and nickel. Our strategy relies on a uniform dispersion of extremely fine sized carbon nanoparticles (2.6 ± 1.2 nm) inside nanograins. The intragranular dispersion of nanoparticles not only elevates the strength of already-strong nanograins by 35%, but also activates multiple hardening mechanisms via dislocation-nanoparticle interactions, leading to improved work hardening and large tensile ductility. In addition, these finely dispersed nanoparticles result in substantially enhanced thermal stability and electrical conductivity in metal nanocomposites. Our results demonstrate the concurrent improvement of several mutually exclusive properties in metals including strength-ductility, strength-thermal stability, and strength-electrical conductivity, and thus represent a promising route to engineering high-performance nanostructured materials.
more »
« less
Crystal plasticity modeling the deformation in nanodomained heterogenous structures
Nanodomained heterogenous structures characterized by randomly dispersed nanograins (NGs) embedded in the coarser grains (CGs) have demonstrated an exciting potential to break the strength–ductility trade-off, providing high strength without the loss of ductility. Here, using a combination of discrete crystal plasticity finite element (discrete-CPFE) model and dislocation density-based CPFE model, we study the effects of grain size, volume fraction of nanograins on the strength and deformation in nanodomained materials. Our analysis shows that the overall flow stresses of nanodomained samples are equal or higher than the strengths predicted by rule of mixtures. Smaller NGs or higher volume fraction of NGs can make the nanodomained samples stronger, as they can be more effective to promote the dislocation accumulations inside the CGs and eventually raise the critical resolved shear stress for each slip system during the plastic flow. Areas surrounding NGs stored higher dislocation densities and less plastic strain, due to the restricted dislocation motion. Furthermore, NGs grain embedded in the CGs can effectively reduce the anisotropy of strength in the nanodomained samples.
more »
« less
- Award ID(s):
- 2015598
- PAR ID:
- 10207460
- Date Published:
- Journal Name:
- Journal of Materials Research
- Volume:
- 34
- Issue:
- 9
- ISSN:
- 0884-2914
- Page Range / eLocation ID:
- 1555 to 1563
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract The operation of fracture, diffusion, and intracrystalline‐plastic micromechanisms during semibrittle deformation of rock is directly relevant to understanding mechanical behavior across the brittle‐plastic transition in the crust. An outstanding question is whether (1) the micromechanisms of semibrittle flow can be considered to operate independently, as represented in typical crustal strength profiles across the brittle to plastic transition, or (2) the micromechanisms are coupled such that the transition is represented by a distinct rheology with dependency on effective pressure, temperature, and strain rate. We employ triaxial stress‐cycling experiments to investigate elastic‐plastic and viscoelastic behaviors during semibrittle flow in two distinctly different monomineralic, polycrystalline, synthetic salt‐rocks. During semibrittle flow at high differential stress, granular, low‐porosity, work‐hardened salt‐rocks deform predominantly by grain‐boundary sliding and wing‐crack opening accompanied by minor intragranular dislocation glide. In contrast, fully annealed, near‐zero porosity salt‐rocks flow at lower differential stress by intragranular dislocation glide accompanied by grain‐boundary sliding and opening. Grain‐boundary sliding is frictional during semibrittle flow at higher strain rates, but the associated dispersal of water from fluid inclusions along boundaries can activate fluid‐assisted diffusional sliding at lower strain rates. Changes in elastic properties with semibrittle flow largely reflect activation of sliding along closed grain boundaries. Observed microstructures, pronounced hysteresis and anelasticity during cyclic stressing after semibrittle flow, and stress relaxation behaviors indicate coupled operation of micromechanisms leading to a distinct rheology (hypothesis 2 above).more » « less
-
Multi-principal element alloys (MPEAs) exhibit outstanding strength attributed to the complex dislocation dynamics as compared to conventional alloys. Here, we develop an atomic-lattice-distortion-dependent discrete dislocation dynamics framework consisted of random field theory and phenomenological dislocation model to investigate the fundamental deformation mechanism underlying massive dislocation motions in body-centered cubic MPEA. Amazingly, the turbulence of dislocation speed is identified in light of strong heterogeneous lattice strain field caused by short-range ordering. Importantly, the vortex from dislocation flow turbulence not only acts as an effective source to initiate dislocation multiplication but also induces the strong local pinning trap to block dislocation movement, thus breaking the strength-ductility trade-off.more » « less
-
Dilute Mg alloys based upon earth-abundant elements, e.g., Al, Ca, and Zn have attractive combinations of strength, ductility, and workability. Even higher strength can be obtained in work-hardened material without the heat treatments required to induce Guinier-Preston zone strengthening of previously studied versions of these alloys. This stems from a slightly stronger crystallographic texture than is present after solutionizing, a high dislocation density, and to a lesser degree, a fine distribution of globular Zn-rich precipitates. The anisotropic plastic response of sheet material is described using an elasto-viscoplastic self-consistent (EVPSC) polycrystal model. Strain partitioning between grains during rolling-induced strain hardening is held responsible for the yield strength, ductility, and especially, strain hardening anisotropy. Texture-induced plastic anisotropy is well- known, but the effect of strong partitioning of strain between variously oriented grains is critical to explain what may be classified as a sort of strain path change (generalized Bauschinger) effect.more » « less
-
Study of the plastic flow and strain-induced phase transformations (PTs) under high pressure with diamond anvils is important for material and geophysics. We introduce rough diamond anvils and apply them to Zr, which drastically change the plastic flow, microstructure, and PTs. Multiple steady microstructures independent of pressure, plastic strain, and strain path are reached. Maximum friction equal to the yield strength in shear is achieved. This allows determination of the pressure-dependence of the yield strength and proves that omega-Zr behaves like perfectly plastic, isotropic, and strain path-independent immediately after PT. Record minimum pressure for alpha-omega PT was identified. Kinetics of strain-induced PT depends on plastic strain and time. Crystallite size and dislocation density in omega-Zr during PT depend solely on the volume fraction of omega-Zr.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1557/jmr.2019.63
