An official website of the United States government
Dilute Mg-Al-Ca-Mn alloys exhibit excellent strength-ductility combinations in the peak-aged condition due to ordered, single atomic layer Guinier-Preston (GP) zones. The present work explains why rolled sheet material is softer and less responsive to aging, as compared to extruded. Using crystal-plasticity modeling, it is shown that the initial texture of the rolled material permits the soft modes, basal slip and twinning, to accommodate more of the strain during in-plane tension, and they are less responsive to hardening by the finely dispersed GP zones. Even with the same number density of GP zones, the extruded material is stronger in tension along the extrusion axis due to an initial texture which forces higher relative activity of prismatic slip, a mode previously shown to be strongly affected by the GP zones. The present work reemphasizes the significant role of the initial texture in determining the strength and anisotropy of non-cubic metals and alloys.
more »
« less
This content will become publicly available on June 1, 2026
Strain partitioning-induced anisotropy in thermomechanically processed magnesium alloys comprised of earth-abundant elements
Dilute Mg alloys based upon earth-abundant elements, e.g., Al, Ca, and Zn have attractive combinations of strength, ductility, and workability. Even higher strength can be obtained in work-hardened material without the heat treatments required to induce Guinier-Preston zone strengthening of previously studied versions of these alloys. This stems from a slightly stronger crystallographic texture than is present after solutionizing, a high dislocation density, and to a lesser degree, a fine distribution of globular Zn-rich precipitates. The anisotropic plastic response of sheet material is described using an elasto-viscoplastic self-consistent (EVPSC) polycrystal model. Strain partitioning between grains during rolling-induced strain hardening is held responsible for the yield strength, ductility, and especially, strain hardening anisotropy. Texture-induced plastic anisotropy is well- known, but the effect of strong partitioning of strain between variously oriented grains is critical to explain what may be classified as a sort of strain path change (generalized Bauschinger) effect.
more »
« less
- Award ID(s):
- 1921926
- PAR ID:
- 10598620
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Scripta Materialia
- Volume:
- 262
- Issue:
- C
- ISSN:
- 1359-6462
- Page Range / eLocation ID:
- 116659
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Stress-strain responses and twinning characteristics are studied for a rolled AZ31B magnesium alloy under three different stress states: tension along the normal direction (NDT), compression along the rolled direction (RDC), and torsion about the normal direction (NDTOR) using companion specimens interrupted at incremental strain levels. Tension twinning is extensively induced in twinning-favorable NDT and RDC. All the six variants of tension twin are activated under NDT, whereas a maximum of four variants is activated under RDC. Under NDTOR, both tension twins and compression twins are activated at relatively large strains and twinning occurs in a small fraction of favored grains rather than in the majority of grains. Secondary and tertiary twins are observed in the favorably-orientated grains at high strain levels. Deformation under each stress state shows three stages of strain hardening rate: fast decrease (Stage I), sequential increase (Stage II), and progressive decrease (Stage III). The increase in the hardening rate, which is more significant under NDT and RDC as compared to NDTOR, is attributed to the hardening effect of twin boundaries and twinning texture-induced slip activities. The hardening effect of twin boundaries include the dynamic Hall-Petch hardening induced by the multiplication of twin boundaries (TBs) and twin-twin boundaries (TTBs) as well as the hardening effect associated with the energetically unfavorable TTB formation. When the applied plastic strain is larger than 0.05 under NDT and RDC, the tension twin volume fraction is higher than 50%. The twinning-induced texture leads to the activation of non-basal slips mainly in the twinned volume, i.e. prismatic slips under NDT and pyramidal slips under RDC. The low work hardening under NDTOR is due to the prevailing basal slips with reduced twinning activities under NDTOR.more » « less
-
In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe42Mn28Co10Cr15Si5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe38.5Mn20Co20Cr15Si5Cu1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. The peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.more » « less
-
This work systematically investigates the texture-property linkages in hexagonal close-packed (hexagonal) materials using a three-dimensional computational crystal plasticity approach. Magnesium and its alloys are considered as a model system. We perform full-field, large-strain, micromechanical simulations using a wide range of surrogate textures that also sample several experimental datasets for a range of Mg alloys. The role of textural variability and the associated sensitivity of deformation mechanisms on the evolution of the macroscopic plastic anisotropy and strength asymmetry is mapped under uniaxial tensile and compressive loading along the material principal and off-axes orientations. To assess the role of crystallographic plastic anisotropy, two distinct material datasets are simulated, which represent pure and alloyed magnesium. The results provide insights into experimental observations reported for magnesium alloys over a range of materials textures. We discuss potential implications on the damage tolerance from the aggregate plastic anisotropy arising from intrinsic crystallographic and textural effects.more » « less
-
null (Ed.)Abstract Lightweight, recyclable, and plentiful Mg alloys are receiving increased attention due to an exceptional combination of strength and ductility not possible from pure Mg. Yet, due to their alloying elements, such as rare-earths or aluminum, they are either not economical or biocompatible. Here we present a new rare-earth and aluminum-free magnesium-based alloy, with trace amounts of Zn, Ca, and Mn (≈ 2% by wt.). We show that the dilute alloy exhibits outstanding high strength and high ductility compared to other dilute Mg alloys. By direct comparison with annealed material of the same chemistry and using transmission electron microscopy (TEM), high-resolution TEM (HR-TEM) and atom probe tomography analyses, we show that the high strength can be attributed to a number of very fine, Zn/Ca-containing nanoscale precipitates, along with ultra-fine grains. These findings show that forming a hierarchy of nanometer precipitates from just miniscule amounts of solute can invoke simultaneous high strength and ductility, producing an affordable, biocompatible Mg alloy.more » « less
