Resonant tunneling diodes (RTDs) have come full-circle in the past 10 years after their demonstration in the early 1990s
as the fastest room-temperature semiconductor oscillator, displaying experimental results up to 712 GHz and fmax values
exceeding 1.0 THz [1]. Now the RTD is once again the preeminent electronic oscillator above 1.0 THz and is being
implemented as a coherent source [2] and a self-oscillating mixer [3], amongst other applications. This paper concerns
RTD electroluminescence – an effect that has been studied very little in the past 30+ years of RTD development, and not
at room temperature. We present experiments and modeling of an n-type In0.53Ga0.47As/AlAs double-barrier RTD
operating as a cross-gap light emitter at ~300K. The MBE-growth stack is shown in Fig. 1(a). A 15-μm-diam-mesa
device was defined by standard planar processing including a top annular ohmic contact with a 5-μm-diam pinhole in the
center to couple out enough of the internal emission for accurate free-space power measurements [4]. The emission spectra
have the behavior displayed in Fig. 1(b), parameterized by bias voltage (VB). The long wavelength emission edge is at
= 1684 nm - close to the In0.53Ga0.47As bandgap energy of Ug ≈ 0.75 eV at 300 K. The spectral peaks for VB = 2.8 and
3.0 V both occur around = 1550 nm (h = 0.75 eV), so blue-shifted relative to the peak of the “ideal”, bulk InGaAs
emission spectrum shown in Fig. 1(b) [5]. These results are consistent with the model displayed in Fig. 1(c), whereby
the broad emission peak is attributed to the radiative recombination between electrons accumulated on the emitter side,
and holes generated on the emitter side by interband tunneling with current density Jinter. The blue-shifted main peak is
attributed to the quantum-size effect on the emitter side, which creates a radiative recombination rate RN,2 comparable to
the band-edge cross-gap rate RN,1. Further support for this model is provided by the shorter wavelength and weaker
emission peak shown in Fig. 1(b) around = 1148 nm. Our quantum mechanical calculations attribute this to radiative
recombination RR,3 in the RTD quantum well between the electron ground-state level E1,e, and the hole level E1,h.
To further test the model and estimate quantum efficiencies, we conducted optical power measurements using a
large-area Ge photodiode located ≈3 mm away from the RTD pinhole, and having spectral response between 800 and
1800 nm with a peak responsivity of ≈0.85 A/W at =1550 nm. Simultaneous I-V and L-V plots were obtained and
are plotted in Fig. 2(a) with positive bias on the top contact (emitter on the bottom). The I-V curve displays a pronounced
NDR region having a current peak-to-valley current ratio of 10.7 (typical for In0.53Ga0.47As RTDs). The external quantum
efficiency (EQE) was calculated from EQE = e∙IP/(∙IE∙h) where IP is the photodiode dc current and IE the RTD current.
The plot of EQE is shown in Fig. 2(b) where we see a very rapid rise with VB, but a maximum value (at VB= 3.0 V) of
only ≈2×10-5. To extract the internal quantum efficiency (IQE), we use the expression EQE= c ∙i ∙r ≡ c∙IQE where
ci, and r are the optical-coupling, electrical-injection, and radiative recombination efficiencies, respectively [6]. Our
separate optical calculations yield c≈3.4×10-4 (limited primarily by the small pinhole) from which we obtain the curve
of IQE plotted in Fig. 2(b) (right-hand scale). The maximum value of IQE (again at VB = 3.0 V) is 6.0%. From the implicit
definition of IQE in terms of i and r given above, and the fact that the recombination efficiency in In0.53Ga0.47As is
likely limited by Auger scattering, this result for IQE suggests that i might be significantly high.
To estimate i, we have used the experimental total current of Fig. 2(a), the Kane two-band model of interband
tunneling [7] computed in conjunction with a solution to Poisson’s equation across the entire structure, and a rate-equation
model of Auger recombination on the emitter side [6] assuming a free-electron density of 2×1018 cm3. We focus on the
high-bias regime above VB = 2.5 V of Fig. 2(a) where most of the interband tunneling should occur in the depletion region
on the collector side [Jinter,2 in Fig. 1(c)]. And because of the high-quality of the InGaAs/AlAs heterostructure (very few
traps or deep levels), most of the holes should reach the emitter side by some combination of drift, diffusion, and tunneling
through the valence-band double barriers (Type-I offset) between InGaAs and AlAs. The computed interband current
density Jinter is shown in Fig. 3(a) along with the total current density Jtot. At the maximum Jinter (at VB=3.0 V) of 7.4×102
A/cm2, we get i = Jinter/Jtot = 0.18, which is surprisingly high considering there is no p-type doping in the device. When
combined with the Auger-limited r of 0.41 and c ≈ 3.4×10-4, we find a model value of IQE = 7.4% in good agreement
with experiment. This leads to the model values for EQE plotted in Fig. 2(b) - also in good agreement with experiment.
Finally, we address the high Jinter and consider a possible universal nature of the light-emission mechanism. Fig.
3(b) shows the tunneling probability T according to the Kane two-band model in the three materials, In0.53Ga0.47As, GaAs,
and GaN, following our observation of a similar electroluminescence mechanism in GaN/AlN RTDs (due to strong
polarization field of wurtzite structures) [8]. The expression is Tinter = (2/9)∙exp[(-2 ∙Ug
2 ∙me)/(2h∙P∙E)], where Ug is the
bandgap energy, P is the valence-to-conduction-band momentum matrix element, and E is the electric field. Values for
the highest calculated internal E fields for the InGaAs and GaN are also shown, indicating that Tinter in those structures
approaches values of ~10-5. As shown, a GaAs RTD would require an internal field of ~6×105 V/cm, which is rarely
realized in standard GaAs RTDs, perhaps explaining why there have been few if any reports of room-temperature
electroluminescence in the GaAs devices.
[1] E.R. Brown,et al., Appl. Phys. Lett., vol. 58, 2291, 1991. [5] S. Sze, Physics of Semiconductor Devices, 2nd Ed. 12.2.1 (Wiley, 1981).
[2] M. Feiginov et al., Appl. Phys. Lett., 99, 233506, 2011. [6] L. Coldren, Diode Lasers and Photonic Integrated Circuits, (Wiley, 1995).
[3] Y. Nishida et al., Nature Sci. Reports, 9, 18125, 2019. [7] E.O. Kane, J. of Appl. Phy 32, 83 (1961).
[4] P. Fakhimi, et al., 2019 DRC Conference Digest. [8] T. Growden, et al., Nature Light: Science & Applications 7, 17150 (2018).
[5] S. Sze, Physics of Semiconductor Devices, 2nd Ed. 12.2.1 (Wiley, 1981).
[6] L. Coldren, Diode Lasers and Photonic Integrated Circuits, (Wiley, 1995).
[7] E.O. Kane, J. of Appl. Phy 32, 83 (1961).
[8] T. Growden, et al., Nature Light: Science & Applications 7, 17150 (2018).
more »
« less
Intrinsic electronic conductivity of individual atomically resolved amyloid crystals reveals micrometer-long hole hopping via tyrosines
Proteins are commonly known to transfer electrons over distances limited to a few nanometers. However, many biological processes require electron transport over far longer distances. For example, soil and sediment bacteria transport electrons, over hundreds of micrometers to even centimeters, via putative filamentous proteins rich in aromatic residues. However, measurements of true protein conductivity have been hampered by artifacts due to large contact resistances between proteins and electrodes. Using individual amyloid protein crystals with atomic-resolution structures as a model system, we perform contact-free measurements of intrinsic electronic conductivity using a four-electrode approach. We find hole transport through micrometer-long stacked tyrosines at physiologically relevant potentials. Notably, the transport rate through tyrosines (105s−1) is comparable to cytochromes. Our studies therefore show that amyloid proteins can efficiently transport charges, under ordinary thermal conditions, without any need for redox-active metal cofactors, large driving force, or photosensitizers to generate a high oxidation state for charge injection. By measuring conductivity as a function of molecular length, voltage, and temperature, while eliminating the dominant contribution of contact resistances, we show that a multistep hopping mechanism (composed of multiple tunneling steps), not single-step tunneling, explains the measured conductivity. Combined experimental and computational studies reveal that proton-coupled electron transfer confers conductivity; both the energetics of the proton acceptor, a neighboring glutamine, and its proximity to tyrosine influence the hole transport rate through a proton rocking mechanism. Surprisingly, conductivity increases 200-fold upon cooling due to higher availability of the proton acceptor by increased hydrogen bonding.
more » « less- Award ID(s):
- 1749662
- NSF-PAR ID:
- 10207736
- Publisher / Repository:
- Proceedings of the National Academy of Sciences
- Date Published:
- Journal Name:
- Proceedings of the National Academy of Sciences
- Volume:
- 118
- Issue:
- 2
- ISSN:
- 0027-8424
- Page Range / eLocation ID:
- Article No. e2014139118
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Conducting probe atomic force microscopy (CP-AFM) was employed to examine electron tunneling in self-assembled monolayer (SAM) junctions. A 2.3 nm long perylene tetracarboxylic acid diimide (PDI) acceptor molecule equipped with isocyanide linker groups was synthesized, adsorbed onto Ag, Au and Pt substrates, and the current–voltage ( I – V ) properties were measured by CP-AFM. The dependence of the low-bias resistance ( R ) on contact work function indicates that transport is LUMO-assisted (‘n-type behavior’). A single-level tunneling model combined with transition voltage spectroscopy (TVS) was employed to analyze the experimental I – V curves and to extract the effective LUMO position ε l = E LUMO − E F and the effective electronic coupling ( Γ ) between the PDI redox core and the contacts. This analysis revealed a strong Fermi level ( E F ) pinning effect in all the junctions, likely due to interface dipoles that significantly increased with increasing contact work function, as revealed by scanning Kelvin probe microscopy (SKPM). Furthermore, the temperature ( T ) dependence of R was found to be substantial. For Pt/Pt junctions, R varied more than two orders of magnitude in the range 248 K < T < 338 K. Importantly, the R ( T ) data are consistent with a single step electron tunneling mechanism and allow independent determination of ε l , giving values compatible with estimates of ε l based on analysis of the full I – V data. Theoretical analysis revealed a general criterion to unambiguously rule out a two-step transport mechanism: namely, if measured resistance data exhibit a pronounced Arrhenius-type temperature dependence, a two-step electron transfer scenario should be excluded in cases where the activation energy depends on contact metallurgy. Overall, our results indicate (1) the generality of the Fermi level pinning phenomenon in molecular junctions, (2) the utility of employing the single level tunneling model for determining essential electronic structure parameters ( ε l and Γ ), and (3) the importance of changing the nature of the contacts to verify transport mechanisms.more » « less
-
In photosynthesis, absorbed light energy transfers through a network of antenna proteins with near-unity quantum efficiency to reach the reaction center, which initiates the downstream biochemical reactions. While the energy transfer dynamics within individual antenna proteins have been extensively studied over the past decades, the dynamics between the proteins are poorly understood due to the heterogeneous organization of the network. Previously reported timescales averaged over such heterogeneity, obscuring individual interprotein energy transfer steps. Here, we isolated and interrogated interprotein energy transfer by embedding two variants of the primary antenna protein from purple bacteria, light-harvesting complex 2 (LH2), together into a near-native membrane disc, known as a nanodisc. We integrated ultrafast transient absorption spectroscopy, quantum dynamics simulations, and cryogenic electron microscopy to determine interprotein energy transfer timescales. By varying the diameter of the nanodiscs, we replicated a range of distances between the proteins. The closest distance possible between neighboring LH2, which is the most common in native membranes, is 25 Å and resulted in a timescale of 5.7 ps. Larger distances of 28 to 31 Å resulted in timescales of 10 to 14 ps. Corresponding simulations showed that the fast energy transfer steps between closely spaced LH2 increase transport distances by ∼15%. Overall, our results introduce a framework for well-controlled studies of interprotein energy transfer dynamics and suggest that protein pairs serve as the primary pathway for the efficient transport of solar energy.more » « less
-
Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m-1 K-1 at room temperature for a 9-walled MWCNT. Theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.more » « less
-
more » « less
Abstract The ability to redirect electron transport to new reactions in living systems opens possibilities to store energy, generate new products, or probe physiological processes. Recent work by Huang et al. showed that 3D crystals of small tetraheme cytochromes (STC) can transport electrons over nanoscopic to mesoscopic distances by an electron hopping mechanism, making them promising materials for nanowires. However, fluctuations at room temperature may distort the nanostructure, hindering efficient electron transport. Classical molecular dynamics simulations of these fluctuations at the nano‐ and mesoscopic scales allowed us to develop a graph network representation to estimate maximum electron flow that can be driven through STC wires. In longer nanowires, transient structural fluctuations at protein‐protein interfaces tended to obstruct efficient electron transfer, but these blockages are ameliorated in thicker crystals where alternative electron transfer pathways become more efficient. The model implies that more flexible proteinprotein interfaces limit the required minimum diameter to carry currents commensurate with conventional electronics.
