Manganese‐rich layered oxide materials hold great potential as low‐cost and high‐capacity cathodes for Na‐ion batteries. However, they usually form a P2 phase and suffer from fast capacity fade. In this work, an O3 phase sodium cathode has been developed out of a Li and Mn‐rich layered material by leveraging the creation of transition metal (TM) and oxygen vacancies and the electrochemical exchange of Na and Li. The Mn‐rich layered cathode material remains primarily O3 phase during sodiation/desodiation and can have a full sodiation capacity of ca. 220 mAh g−1. It delivers ca. 160 mAh g−1specific capacity between 2–3.8 V with >86 % retention over 250 cycles. The TM and oxygen vacancies pre‐formed in the sodiated material enables a reversible migration of TMs from the TM layer to the tetrahedral sites in the Na layer upon de‐sodiation and sodiation. The migration creates metastable states, leading to increased kinetic barrier that prohibits a complete O3‐P3 phase transition.
Manganese‐rich layered oxide materials hold great potential as low‐cost and high‐capacity cathodes for Na‐ion batteries. However, they usually form a P2 phase and suffer from fast capacity fade. In this work, an O3 phase sodium cathode has been developed out of a Li and Mn‐rich layered material by leveraging the creation of transition metal (TM) and oxygen vacancies and the electrochemical exchange of Na and Li. The Mn‐rich layered cathode material remains primarily O3 phase during sodiation/desodiation and can have a full sodiation capacity of ca. 220 mAh g−1. It delivers ca. 160 mAh g−1specific capacity between 2–3.8 V with >86 % retention over 250 cycles. The TM and oxygen vacancies pre‐formed in the sodiated material enables a reversible migration of TMs from the TM layer to the tetrahedral sites in the Na layer upon de‐sodiation and sodiation. The migration creates metastable states, leading to increased kinetic barrier that prohibits a complete O3‐P3 phase transition.
more » « less- NSF-PAR ID:
- 10236622
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Angewandte Chemie
- Volume:
- 133
- Issue:
- 15
- ISSN:
- 0044-8249
- Page Range / eLocation ID:
- p. 8339-8348
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Li‐rich layered chalcogenides have recently led to better understanding of the anionic redox process and its associated high capacity while providing ways to overcome its practical limitations of voltage fade and irreversibility. This study reports on the feasibility of triggering anionic activity in Li2TiS3, through anionic substitution (Se for S) or cationic substitution (Fe for Ti). Herein, the chalcogenide chemical space is further explored to prepare mono‐substituted Li1.7Ti0.85Mn0.45Ch3(Ch = S/Se) and doubly substituted cationic and anionic phases (Li1.7Ti0.85Fe0.45S3‐zSez) which crystallize either in the O3‐ or O1‐type structures depending upon substituents. All series show a bell‐shape capacity variation as function of the transition metal (TM) substitution degree with values up to 240 mAh g−1. For specific compositions, a structural O3 to O1 phase transition is observed upon Li removal, which is not reversible upon Li re‐insertion due to kinetic limitations and negatively affects long‐term cycling performance. Density functional theory (DFT) calculations confirm the O3/O1 relative stability along the different series and point subtle electronic differences in the TM‐doping, rationalizing the structural and electrochemical behaviors of these phases upon cycling. These findings provide further insights into the link between structural and electronic stability, which is of key importance for designing chalcogenide‐based anionic redox compounds.
-
more » « less
Abstract Layered transition metal oxides are appealing cathodes for sodium‐ion batteries due to their overall advantages in energy density and cost. But their stabilities are usually compromised by the complicated phase transition and the oxygen redox, particularly when operating at high voltages, leading to poor structural stability and substantial capacity loss. Here an integrated strategy combing the high‐entropy design with the superlattice‐stabilization to extend the cycle life and enhance the rate capability of layered cathodes is reported. It is shown that the as‐prepared high‐entropy Na2/3Li1/6Fe1/6Co1/6Ni1/6Mn1/3O2cathode enables a superlattice structure with Li/transition metal ordering and delivers excellent electrochemical performance that is not affected by the presence of phase transition and oxygen redox. It achieves a high reversible capacity (171.2 mAh g−1at 0.1 C), a high energy density (531 Wh kg−1), extended cycling stability (89.3% capacity retention at 1 C for 90 cycles and 63.7% capacity retention at 5 C after 300 cycles), and excellent fast‐charging capability (78 mAh g−1at 10 C). This strategy would inspire more rational designs that can be leveraged to improve the reliability of layered cathodes for secondary‐ion batteries.
-
more » « less
Abstract Mn‐redox‐based oxides and oxyfluorides are considered the most promising earth‐abundant high‐energy cathode materials for next‐generation lithium‐ion batteries. While high capacities are obtained in high‐Mn content cathodes such as Li‐ and Mn‐rich layered and spinel‐type materials, local structure changes and structural distortions ( often lead to voltage fade, capacity decay, and impedance rise, resulting in unacceptable electrochemical performance upon cycling. In the present study, structural transformations that exploit the high capacity of Mn‐rich oxyfluorides while enabling stable cycling, in stark contrast to commonly observed structural changes that result in rapid performance degradation, are reported. It is shown that upon cycling of a cation‐disordered rocksalt (DRX) cathode (Li1.1Mn0.8Ti0.1O1.9F0.1, an ultrahigh capacity of ≈320 mAh g−1(energy density of ≈900 Wh kg−1) can be obtained through dynamic structural rearrangements upon cycling , along with a unique voltage profile evolution and capacity rise. At high voltage, the presence of Mn4+and Li+vacancies promotes local cation ordering, leading to the formation of domains of a “
δ phase” within the disordered framework. On deep discharge, Mn4+reduction, along with Li+insertion transform the structure to a partially ordered DRX phase with aβ ′‐LiFeO2‐type arrangement. At the nanoscale, domains of the in situ formed phases are randomly oriented, allowing highly reversible structural changes and stable electrochemical cycling. These new insights not only help explain the superior electrochemical performance of high‐Mn DRXbut also provide guidance for the future development of Mn‐based, high‐energy density oxide, and oxyfluoride cathode materials. -
more » « less
Abstract Rechargeable aqueous batteries with Zn2+as a working‐ion are promising candidates for grid‐scale energy storage because of their intrinsic safety, low‐cost, and high energy‐intensity. However, suitable cathode materials with excellent Zn2+‐storage cyclability must be found in order for Zinc‐ion batteries (ZIBs) to find practical applications. Herein, NaCa0.6V6O16·3H2O (NaCaVO) barnesite nanobelts are reported as an ultra‐stable ZIB cathode material. The original capacity reaches 347 mAh g−1at 0.1 A g−1, and the capacity retention rate is 94% after 2000 cycles at 2 A g−1and 83% after 10 000 cycles at 5 A g−1, respectively. Through a combined theoretical and experimental approach, it is discovered that the unique V3O8layered structure in NaCaVO is energetically favorable for Zn2+diffusion and the structural water situated between V3O8layers promotes a fast charge‐transfer and bulk migration of Zn2+by enlarging gallery spacing and providing more Zn‐ion storage sites. It is also found that Na+and Ca2+alternately suited in V3O8layers are the essential stabilizers for the layered structure, which play a crucial role in retaining long‐term cycling stability.
