An official website of the United States government
The quartz crystal monitor (QCM) is a common sensor platform based on the room temperature compensated pure shear mode (PSM) of thickness field excited (TFE) AT-cut quartz. However, with electrodes on both crystal faces, TFE only allows sensing of mechanical property changes. Lateral field excitation (LFE), where both electrodes are on a single face, enables the detection of both mechanical and electrical changes, potentially leading to higher sensitivity. As lithium tantalate (LT) has an LFE PSM and piezoelectric coupling several times greater than that of quartz, LFE LT was chosen as a possible replacement for TFE quartz. A theoretical search of all LT cuts identified those exhibiting a room temperature compensated PSM. A set of orientations ranging from (YXwl) 0°/-85° to 0°/-90° was chosen for experimental verification. The temperature response of each sample was shown to be parabolic, with a roughly linear relationship between crystal cut angle and temperature inflection point/turnaround temperature. Specifically, the (YXwl) 0°/-87° cut with a turnaround temperature at 26.4°C demonstrates that a room temperature PSM in LT can be excited via LFE. Future work focusing on the development of an LT sensing platform could profoundly impact sensor systems in agriculture, homeland security, global warming, and medical applications.
more »
« less
Relationship Between Lateral Field Excited AT-Cut Quartz Crystal Microbalance Operation and Acoustic Plate Modes
The operational modes of lateral field excited (LFE) quartz crystal microbalances (QCMs) under various electrical boundary conditions have been under investigation for use in sensing applications. The present results indicate connections between the behaviors of acoustic plate modes (APMs) and LFE-QCM modes. The influences of deposited thin conducting and semiconducting films on the mode responses of LFE-QCMs strongly agree with reported effects on APMs. Thus the main operating modes of LFE devices are concluded to be laterally varying APMs, which may be close in character to thickness modes. Mode response changes caused by slowly varying surface curvature are explained from this perspective. The consistency of the usual LFE thickness mode coupling formalism is evaluated, and the superposition of partial waves method is found to be more appropriate for analyzing LFE devices. This view of LFE devices operating through APMs supports improved sensing applications and investigations through access to existing APM knowledge.
more »
« less
- Award ID(s):
- 1701087
- PAR ID:
- 10273419
- Date Published:
- Journal Name:
- Proceedings of the 2020 IEEE International Ultrasonics Symposium (IUS)
- Page Range / eLocation ID:
- 1 to 4
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The most common bulk acoustic wave device used in biosensing applications is the quartz crystal microbalance (QCM), in which a resonant pure shear acoustic wave is excited via electrodes on both major faces of a thin AT-cut quartz plate. For biosensing, the QCM is used to detect the capture of a target by a target-capture film. The sensitivity of the QCM is typically based solely on the detection of mechanical property changes, as electrical property change detection is limited by the electrode on its sensing surface. A modification of the QCM called the lateral field excited (LFE) QCM (LFE-QCM) has been developed with a bare sensing surface as both electrodes are now on a single face of the quartz plate. Compared to the QCM, the LFE-QCM exhibits significantly higher sensitivity to both electrical and mechanical property changes. This paper presents theoretical and experimental aspects of LFE-QCMs. In particular, the presence and strength of the usual and newfound LFE-QCM modes depend on the electrical properties of the film and/or sensing environment. This work also presents examples of experimental setups for measuring the response of an LFE-QCM, followed by results of LFE-QCMs used to detect liquid electrical and mechanical properties, chemical targets, and biological targets. Finally, details are given about the attachment of various target-capture films to the LFE-QCM surface to capture biomarkers associated with diseases such as cancer.more » « less
-
We experimentally demonstrate bridge-coupled metallo-dielectric nanolasers that can operate in the in-phase or out-of-phase locking modes at room temperature. By varying the length of the bridge, we show that the coupling coefficients can be realized in support of the stable operation of any of these two modes. Both coupled nanolaser designs have been fabricated and characterized for experimental validation. Their lasing behavior has been confirmed by the spectral evolution, light-in light-out characterizations, and emission linewidth narrowing. The operating mode is identified from the near-field and far-field emission pattern measurements. To the best of our knowledge, this is the first demonstration of mode selection in bridge-coupled metallo-dielectric nanolasers, which can serve as building blocks in nanolaser arrays for applications in imaging, virtual reality devices, and lidars.more » « less
-
Abstract Implementing microelectromechanical system (MEMS) resonators calls for detailed microscopic understanding of the devices, such as energy dissipation channels, spurious modes, and imperfections from microfabrication. Here, we report the nanoscale imaging of a freestanding super-high-frequency (3 – 30 GHz) lateral overtone bulk acoustic resonator with unprecedented spatial resolution and displacement sensitivity. Using transmission-mode microwave impedance microscopy, we have visualized mode profiles of individual overtones and analyzed higher-order transverse spurious modes and anchor loss. The integrated TMIM signals are in good agreement with the stored mechanical energy in the resonator. Quantitative analysis with finite-element modeling shows that the noise floor is equivalent to an in-plane displacement of 10 fm/√Hz at room temperatures, which can be further improved under cryogenic environments. Our work contributes to the design and characterization of MEMS resonators with better performance for telecommunication, sensing, and quantum information science applications.more » « less
-
null (Ed.)Acoustic devices have played a major role in telecommunications for decades as the leading technology for filtering in RF and microwave frequencies. While filter requirements for insertion loss and bandwidth become more stringent, more functionality is desired for many applications to improve overall system level performance. For instance, a filter with non-reciprocal transmission can minimize losses due to mismatch and protect the source from reflections while also performing its filtering duties. A device such as this one was originally researched by scientists decades ago. These devices were based on the acoustoelectric effect where surface acoustic waves (SAW) traveling in the same direction are as drift carriers in a nearby semiconductor are amplified. While several experiments were successfully demonstrated in [1], [2], [3]. these devices suffered from extremely high operating electric fields and noise figure [4], [5]. In the past few years, new techniques have been developed for implementing non-reciprocal devices such as isolators and circulators without utilizing magnetic materials [6], [7], [8], [9]. The most popular technique has been spatio-temporal modulation (STM) where commutated clock signals synchronized with delay elements result in non-reciprocal transmission through the network. STM has also been adapted by researchers to create non-reciprocal filters. The work in [10] utilizes 4 clocks signals to obtain a non-reciprocal filter with an insertion loss of -6.6 dB an isolation of 25.4 dB. Another filter demonstrated in [11] utilizes 6 synchronized clock signals to obtain a non-reciprocal filter with an insertion loss of -5.6 dB and an Isolation of 20 dB. In this work, a novel non-reciprocal topology is explored with the use of only one modulation signal. The design is based on asymmetrical SAW delay lines with a parametric amplifier. The device can operate in two different modes: phase coherent mode and phase incoherent mode. In phase coherent mode, the device is capable of over +12 dB of gain and 20.2 dB of isolation. A unique feature of this mode is that the phase of the pump signal can be utilized to tune the frequency response of the filter. Under the phase-incoherent mode, the pump frequency remains constant and the device behaves as a normal filter with non-reciprocal transmission exhibiting over +7 dB of gain and 17.33 dB of isolation. While the tuning capability is lost in this mode, phase-coherence is no longer necessary so the device can be utilized in most filtering applications.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/IUS46767.2020.9251368
