skip to main content


Title: All glass, compression-dominant polyhedral bridge prototype: form-finding and fabrication
The recent development of three-dimensional graphic statics using polyhedral reciprocal diagrams (PGS) has greatly increased the ease of designing complex yet efficient spatial funicular structural forms, where the inherent planarity of the polyhedral geometries can be harnessed for efficient construction processes. Our previous research has shown the feasibility of leveraging this planarity in materializing a 10m-span, double-layer glass bridge made of 1cm glass sheets. This paper presents a smaller bridge prototype with a span of 2.5m to address the larger bridge’s challenges regarding form-finding, detail developments, fabrication constraints, and assembly logic. The compression-only prototype is designed for prefabrication as a modular system using PolyFrame for Rhinoceros. Thirteen polyhedral cells of the funicular bridge are materialized in the form of hollow glass units (HGUs) and can be prefabricated and assembled on-site. Each HGU consists of two deck plates and multiple side plates held together using 3M™ Very High Bond (VHB) tape. A male-female glass connection mechanism is developed at the sides of HGUs to interlock each unit with its adjacent cells to prevent sliding. A transparent interface material is placed between the male and female connecting parts to avoid local stress concentration. This novel construction method significantly simplifies the bridge’s assembly on a large scale. The design and construction of this small-scale prototype set the foundation for the future development of the full-scale structure.  more » « less
Award ID(s):
2037097
NSF-PAR ID:
10303794
Author(s) / Creator(s):
; ; ; ; ; ; ;
Date Published:
Journal Name:
Proceedings of the International Association of Shell and Spatial Structures
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. The recent development of three-dimensional graphic statics (3DGS) has greatly increased the ease of designing complex and efficient spatial funicular structural forms [1]. The reciprocal diagram based 3DGS approaches not only generate highly efficient funicular structures [2], but also result in planarity constraints due to the polyhedron nature of the reciprocal diagrams [3]. Our previous research has shown the feasibility of leveraging this planarity by using planar glass sheets to materialize the 10m-span, double-layer glass bridge [3]. This paper is framed as a proof of concept for the 10m bridge and explores the form-finding, detail configuration, fabrication constraints, and assembly logic by designing and constructing a small-scale bridge prototype with a span of 2.5m. The prototype is designed in a modular approach, where each polyhedral cell of the form is materialized using a hollow glass unit (HGU) (Figure 1a), which can be prefabricated and preassembled, and therefore, greatly simplifies the assembly of the whole bridge. The compression-only form of the prototype is generated using the PolyFrame beta [4] plug-in for Rhinoceros [5]. The form-finding is carried out with a comprehensive consideration of a variety of parameters, including fabrication constraints, assembly ease, construction cost, and practicality. To start the form-finding process, a group of closed convex force polyhedrons is aggregated, controlling the topology of the form diagram and the orientations of the form elements. By manipulating the face tilting angles of the force diagram, the supported edges at the end of the bridge are all made horizontal, reducing the difficulty of the support design. Then, vertex locations and edge lengths of the form diagram are constrained, determining the final dimensions of both the bridge and the cells. After getting the geometry of the bridge, the detail developments are streamlined. Each of the 13 HGUs consists of two flat deck plates and a series of side plates (Figure 1b). To interlock the adjacent cells and prevent possible sliding, a male-female connection mechanism is introduced to the conjoint side plates of the HGUs (Figure 1b). Additionally, to eliminate the direct contact of the glass parts and prevent the stress concentration, two softer transparent materials are involved for connecting purposes. Within each HGU, silicon-based binding agent is used to hold the glass parts together; between the neighboring HGUs, plastic sheets are placed as interface materials (Figure 1b). Figure 1. a) The 2.5m-span small-scale prototype dome, b) Exploded view showing deck plates, side plates, male-female connection, and interface material For the fabrication of the glass parts, 5-axis Waterjet cutting techniques are applied. While the glass sheets for the deck plates can be purchased from the market, the irregular side plates with male-female connections need to be made from kiln-cast glass. In terms of the Waterjet cutting constraints, there is a max cutting angle of 60 degrees from vertical. With respect to this, all the glass parts are examined during the design process to ensure they all satisfy the cutting angle requirements. Aiming to achieve a fast and precise assembly, several assistant techniques are developed. On the local HGU level, assembly connectors are designed and 3D-printed to help locate the glass parts. On the global prototype level, the assembly sequence of the HGUs are simulated to avoid interference. Besides, a labeling system is also established to organize the fabricated parts and guide the entire assembly process. The design and construction of this small-scale prototype provide important information for the future development of the full-scale bridge regarding the interlocking detail design, the fabrication constraints, and assembly logic. The actual structural performance of the prototype awaits further investigation through-loading experiments. 
    more » « less
  2. Polyhedral Graphic Statics (PGS) is an effective tool for form-finding and constructing complex yet efficient spatial funicular structures. The intrinsic planarity of polyhedral geometries can be leveraged for efficient fabrication and construction using flat sheet materials, such as glass. Our previous research used PGS for the form-finding of a 3 m-span, modular glass bridge prototype to be built with thirteen unique hollow glass units (HGUs) in a compression-only configuration. This paper reports its design optimization, fabrication, and subsequent modular assembly process. The computational modeling of the geometries is facilitated with the efficient half-face data structure provided by PolyFrame, a software that implements PGS. Regular float glass and acrylic are selected as the main structural materials, and they are fabricated using 5-axis water jet cutting and CNC milling techniques. With the help of 3 M™ Very High Bond tape, the glass parts and acrylic parts are bonded as HGUs, which serve as the basic structural and assembly modules. Surlyn sheets are used as interface material to prevent glass-to-glass direct contact between HGUs. The digital model is also simulated using ANSYS to ensure the effectiveness of the design. Due to the lightweight of the HGUs, the assembly of the bridge can be done by one person without the requirement of any heavy construction machinery. 
    more » « less
  3. null (Ed.)
    This research presents an experimental program executed to understand the strength and stiffness properties of hollow built-up glass compression members that are intended for use in the modular construction of all glass, compression-dominant, shell-type structures. The proposed compression-dominant geometric form has been developed using the methods of form finding and three-dimensional graphical statics. This research takes the first steps towards a new construction methodology for glass structures where individual hollow glass units (HGU) are assembled using an interlocking system to form large, compression-dominant, shell-type structures, thereby exploiting the high compression strength of glass. In this study, an individual HGU has an elongated hexagonal prism shape and consists of two deck plates, two long side plates, and four short side plates, as is shown in Figure 1. Connections between glass plates are made using a two-sided transparent structural adhesive tape. The test matrix includes four HGUs, two each fabricated with 1 mm and 2 mm thick adhesive tape. All samples are dimensioned 64 cm on the long axis of symmetry, 51 cm on the short axis of symmetry, and are 10 cm in width. Glass plates are all 10 mm thick annealed float glass with geometric fabrication done using 5-axis abrasive water jet cutting. HGU assembly is accomplished using 3D printed truing clips and results in a rigid three-dimensional glass frame. Testing was done with the HGU oriented such that load was introduced on the short side edges of the two deck plates, resulting in an asymmetric load-support condition. A soft interface material was used between the HGU and steel plates of the hydraulic actuator and support for the purpose of avoiding premature cracking from local stress concentrations on the glass edges at the load and support locations. Force was applied in displacement control at 0.25 mm/minute with a full array of displacement and strain sensors. Test results for load vs. center deck plate transverse deflection are shown in Figure 2. All samples failed explosively by flexural buckling with no premature cracking on the load and support edges of the deck plates. Strain and deformation data clearly show the presence of second-order behavior resulting from bending deformation perpendicular to the plane of the deck plates. In general, linear axial behavior transitions to nonlinear second-order behavior, with increasing rates in deflection and strain growth, ultimately ending in glass fracture on the tension surfaces of the buckled deck plates. The failure resulted in near-complete disintegration of the deck plates, but with no observable cracking in any side plates and a secure connection on all adhesive tape. Results of the experimental program clearly demonstrate the feasibility of using HGUs for modular construction of compression dominant all-glass shell-type structures. This method of construction can significantly reduce the self-weight of the structure, and it will inspire the use of sustainable materials in the construction of efficient structures. 
    more » « less
  4. Akbarzadeh, Masoud ; Aviv, Dorit ; Jamelle, Hina ; Stuart-Smith, Robert (Ed.)
    Designed with Polyhedral Graphic Statics (PGS), a geometry- based structural form-finding method, Tortuca presents an efficient and innovative structural system constructed by the dry assembly of thirteen hollow glass units (HGU). It also proposes a new language for glass that is carefully treated, structurally informed, fabrication-aware, and environmentally responsible. Each HGU of Tortuca is made of 1 cm (3/8 inch) glass deck plates and 2 cm (0.7 inch) acrylic side plates precisely cut with 5-axis abrasive waterjet cutting and CNC milling to match the structural geometry. The structure spans 3.2 m (10.5 ft) with a mass of only 250 kg (550 lbs), where the float glass is the primary loadbearing material. Thanks to the efficiency and light weight of the construction system, a single person can assemble and disassemble the structure without needing a crane or additional labor. Moreover, this research explores the potential of using an extremely delicate material such as float glass for the primary structural system to encourage minimizing the material and energy demands in buildings and infrastructural projects. Additionally, it shows how utilizing the material in its purest format could simplify the recycling process after the life cycle of the structure has ended. Also, this research project is achieved by collaboration across different institutions, from design to engineering, from theoretical to practical, and from academia to industry. We appreciate the value of breaking disciplinary boundaries and joining forces from multiple fields. 
    more » « less
  5. Multi-layer spatial structures usually take considerable external loads with a small material usage at all scales. Polyhedral graphic statics (PGS) provides a method to design multi-layer funicular polyhedral structures, and the structural forms are usually materialized as space frames. Our previous research shows that the intrinsic planarity of the polyhedral geometries can be harnessed for efficient fabrication and construction processes using flat-sheet materials. Sheet-based structures are advantageous over conventional space frame systems because sheets can provide more load paths and constrain the kinematic degrees of freedom of the nodes. Therefore, they are more capable of taking a wider variety of load cases compared to space frames. Moreover, sheet materials can be fabricated into complex shapes using CNC milling, laser cutting, water jet cutting, and CNC bending techniques. However, not all sheets are necessary as long as the load paths are preserved and the system does not have kinematic degrees of freedom. To find an efficient set of faces that satisfies the requirements, this paper first incorporates and adapts the matrix analysis method to calculate the kinematic degrees of freedom for sheet-based structures. Then, an iterative algorithm is devised to help find a reduced set of faces with zero kinematic degrees of freedom. To attest to the advantages of this method over bar-node construction, a comparative study is carried out using finite element analysis. The results show that, with the same material usage, the sheet-based system has improved performance than the framework system under a range of loading scenarios. 
    more » « less