An official website of the United States government
This manuscript describes the first application of ultrafast-laser-absorption spectroscopy (ULAS) to characterizing high-pressure (up to 40 bar), multi-phase combustion gases. Single-shot measurements of temperature and CO were acquired at 5 kHz in AP-HTPB propellant flames with and without aluminum. An ultrafast light source was used to produce broadband pulses of light near 4.96 𝜇m at a repetition rate of 5 kHz and a high-speed mid-infrared imaging spectrometer was used to image the pulses across an 86 nm bandwidth with a spectral resolution of 0.7 nm. Measurements of temperature and CO concentration were obtained by least-squares fitting simulated absorbance spectra of CO to measured spectra. A system of corrective optics was used to diminish the e˙ect of beam steering during high-pressure experiments, greatly increasing the pressure capabilities of the diagnostic. The diagnostic was used to characterize AP-HTPB propellant flames in an argon bath gas at pressures of 1, 10, 20, and 40 bar. An aluminized AP-HTPB propellant was also characterized at 10 and 20 bar to demonstrate that ULAS can provide high-fidelity measurements in particulate-laden flames. The results demonstrate that ULAS is capable of providing single-shot temperature and species measurements at high pressures with 1-𝜎 precisions less than 1.1% and 3% for temperature and species respectively, despite non-absorbing transmission losses in excess of 90%.
more »
« less
Ultrafast-laser-absorption spectroscopy in the mid-infrared for single-shot, calibration-free temperature and species measurements in low- and high-pressure combustion gases
This manuscript presents an ultrafast-laser-absorption-spectroscopy (ULAS) diagnostic capable of providing calibration-free, single-shot measurements of temperature and CO at 5 kHz in combustion gases at low and high pressures. Additionally, this diagnostic was extended to provide 1D, single-shot measurements of temperature and CO in a propellant flame. A detailed description of the spectral-fitting routine, data-processing procedures, and determination of the instrument response function are also presented. The accuracy of the diagnostic was validated at 1000 K and pressures up to 40 bar in a heated-gas cell before being applied to characterize the spatiotemporal evolution of temperature and CO in AP-HTPB and AP-HTPB-aluminum propellant flames at pressures between 1 and 40 bar. The results presented here demonstrate that ULAS in the mid-IR can provide high-fidelity, calibration-free measurements of gas properties with sub-nanosecond time resolution in harsh, high-pressure combustion environments representative of rocket motors.
more »
« less
- Award ID(s):
- 1834972
- PAR ID:
- 10307851
- Publisher / Repository:
- Optical Society of America
- Date Published:
- Journal Name:
- Optics Express
- Volume:
- 29
- Issue:
- 19
- ISSN:
- 1094-4087; OPEXFF
- Format(s):
- Medium: X Size: Article No. 30140
- Size(s):
- Article No. 30140
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The ammonia (NH3) and dimethyl ether (DME) mixture is a promising alternative fuel that offers the potential for cleaner combustion. This study presents an investigation of the autoignition-assisted flame speeds of stochiometric NH3/DME mixtures under conditions relevant to practical combustion systems. Experiments were conducted at pressures of 5 and 10 bar, gas temperatures ranging from 625 to 708 K, and three DME concentrations (10, 20, and 30%, mole fraction basis) in NH3/DME fuel mixtures using a rapid compression machine-flame (RCM-Flame) apparatus. For the majority of the autoignition experiments, first-stage ignition delay time was observed. Thus, the flame experiments were performed by igniting the spark both before and after the first-stage ignition delay time. The results are presented in terms of the Beta-Damköhler Number, defined as the ratio of spark ignition time to the first-stage ignition delay. The flame speed changes depending on the Beta-Damköhler Number, pressure, gas temperature, and DME concentration. The flame speed increases by increasing the temperature, decreasing the pressure, and increasing DME concentrations. However, the effect of Beta-Damköhler Number on flame speed is complicated: with 10% DME in the mixture, the flame speed is independent to Beta-Damköhler Number, and slight observed slight decrease of flame speed is due to the temperature drop during the post-compression period; with 20% DME in the mixture, at both pressures, the flame speed jumps after the first ignition delay (or Beta-Damköhler Number of one) , and remains constant before and after; similar behavior was observed with 30% DME in the mixture at 5 bar, however, at some temperatures, the flame speed increases at Beta-Damköhler Number of greater than one, and at 10 bar, the first ignition delay was short and flame speed was not measured at Beta-Damköhler Number of less than one. For all studied conditions, a linear trend was observed between burning velocity and stretch rate. Positive Markstein lengths were observed at most conditions, except for two specific gas temperatures (664 K at 5 bar and 671 K at 10 bar) with 30% DME, where negative Markstein lengths are found. One-dimensional laminar flame speed simulations agreed with measured data for Beta-Damköhler Numbers. less than one, but underpredicted the measured data at other conditions.more » « less
-
null (Ed.)A novel laser absorption sensing strategy has been developed to evaluate combustion progress through quantitative measurements of carbon dioxide (CO2) in high-pressure (> 50 atm), high-temperature (> 3000 K) hydrocarbon-fueled rocket combustion flows. The sensor enables a broad range of operability by probing rovibrational transitions in the bandhead of CO2 near 4.2 m, accessed with an interband cascade laser. Under extreme rocket conditions, this targeted bandhead region experiences line-mixing effects that favorably distort the molecular spectra. A preliminary spectroscopic model of line-mixing effects has been developed utilizing a high-enthalpy shock tube to achieve scalability of spectral simulations over a range of high temperatures and high pressures. The model is employed for quantitative interpretation of measured absorption signals. The mid-infrared light source was fiber-coupled for remote light delivery at propulsion test facilities. A wavelength modulation spectroscopy technique utilizing normalized-second harmonic detection was implemented for acquiring differential absorption signals in a harsh rocket combustor environment. Using this method, measurements of CO2 concentration have been demonstrated over a range of operating conditions up to 83 bar in a single-element-injector RP-2/GOx rocket combustor at the Air Force Research Laboratory in Edwards, CA.more » « less
-
Since its implementation, exhaust gas recirculation has proven to be a reliable technique to control NOx emissions by lowering combustion temperature. Dilution with exhaust gas recirculation, whether in internal combustion engines or sequential-staged gas turbine combustors, affects flame reactivity and stability, which are related to the heat release rate and engine power. Another way to control emissions is to use hydrogen as a carbon-free alternative fuel, which is considered a milestone in the energy-decarbonization journey. However, the high reactivity of hydrogen is one of its hurdles and understanding this effect on laminar burning velocity is important. Flame propagation and burning velocity control the mixture reactivity and exothermicity and are related to abnormal combustion phenomena, such as flashback and knock. Therefore, understanding the effect of exhaust gas addition on the laminar burning velocity of hydrogen/air mixtures is imperative for engine design. In this work, a constant volume combustion chamber was used to observe the laminar burning velocity of stoichiometric hydrogen/air mixtures diluted with combustion products at 1 bar and 423K. Actual combustion products (35 % H2O + 65 % N2, by mole) were used for dilution at rates of 0-50%. The burned gas Markstein length was calculated for all mixtures. Experimental results of the laminar burning velocities for all mixtures were compared with kinetic modeling results. These measurements showed the monotonic reduction of reactivity and the laminar burning velocity with dilution. The reduced burning rates at higher dilution were reflected on the pressure gradient inside the vessel. Markstein length values decreased with dilution, meaning that flame instabilities increased with dilution.more » « less
-
To assess the fire hazard associated with venting gases coming from a lithium-ion battery during a thermal runaway, a mixture representative of such venting gas was determined by averaging 40 gas compositions presented in the literature. The final mixture is composed of C3H8, C2H6, C2H4, CH4, H2, CO, and CO2. The combustion properties of this mixture were determined using various combustion devices: shock tubes for ignition delay time measurements in air and for H2O time histories in very dilute mixtures (99% Ar), as well as a closed bomb to measure the laminar flame speeds. Experiments were performed at around atmospheric pressure and for several equivalence ratios in all cases. Several detailed kinetics models from the literature were assessed against the data generated with this very complex mixture, and it was found that modern detailed kinetics mechanisms were capable of appropriately predicting the combustion properties of thermal runaway gases from a battery in most cases, with the NUIGMech 1.1 model being the most accurate. A numerical analysis was conducted with the two most modern models to explain the results and highlight the most important reactions.more » « less
