The thermoacoustic effect provides a means to convert acoustic energy to heat and vice versa without the need for moving parts. This enables the realization of mechanically robust, noise mitigating energy harvesters, although there are limitations to the power-to-volume ratio achievable. The mechanical, thermal, and geometric properties of the porous stack that forms a set of acoustic waveguides in thermoacoustic devices are key to its performance. In this feasibility study, first, various 4-in. diameter ceramic and polymeric stack designs are evaluated using a custom-built thermoacoustic test rig. Influence of stack parameters such as material, length, location, porosity, and pore geometry are correlated to simulations using DeltaEC, a software tool based on Rott’s linear approximation. An acousto-thermo-electric transduction scheme is employed to harvest useable electrical power using the best performing stack. Steady-state peak voltage generated was 33.5 mV for a temperature difference of 34 °C between thehot and cold sides of the stack at an acoustic excitation frequency of 117.5 Hz. Further investigations are underway to establish structure-performance relationships by extracting scaling laws for power-to-volume ratio and frequency-thermal gradient dependencies.
more »
« less
Evaluation of additively manufactured stacks for thermo-acoustic devices
The thermo-acoustic effect provides a means to convert acoustic energy to heat and vice versa without the need for moving parts. This is especially useful to construct mechanically-simple and robust energy harvesting devices, although there are limitations to the power-to-volume ratio achievable. The mechanical and thermal properties as well as geometry of the porous stack that forms a set of acoustic waveguides in thermo-acoustic devices are key to its performance. In this study, we evaluate various additively manufactured polymer stacks against more conventional ceramic stacks using a benchtop thermos-acoustic refrigerator rig that uses air at ambient pressure as its working fluid. Influence of stack parameters such as material, length, location, porosity and pore geometry are examined using experiments and correlated to simulations using DeltaEC, a software tool based on Rott's linear approximation. Structure-performance relationships are established by extracting scaling laws for power-to-volume ratio and frequency-thermal gradient dependencies. It is found that additively manufactured stacks can deliver performance comparable to ceramic stacks while being more affordable and customizable for thermo-acoustic transduction applications.
more »
« less
- Award ID(s):
- 2033399
- NSF-PAR ID:
- 10309617
- Date Published:
- Journal Name:
- INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Volume:
- 263
- Issue:
- 2
- ISSN:
- 0736-2935
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The thermoacoustic effect provides a means to convert acoustic energy to heat and vice versa without the need for moving parts. This could enable the realization of mechanically-robust, noise mitigating energy harvesters via the development of thermoacoustic metastructures using additive and hybrid fabrication processes and materials. The mechanical, thermal and geometric properties of the porous stack that forms a set of acoustic waveguides in thermoacoustic metastructures are key to their performance. In this proof-ofconcept study, firstly, various ceramic and polymeric stack designs are evaluated using a custom-built thermoacoustic test rig. Influence of stack parameters such as material, length, location, porosity and pore geometry are correlated to simulations using DeltaEC, a software tool based on Rott’s linear approximation. Preliminary results also show a reduction in sound pressure level of around 5.28 dB across the thermoacoustic metastructure at resonance (117.5 Hz). An acousto-thermo-electric transduction scheme is employed to harvest useable electrical power using the best performing stack. Steady-state peak voltage generated was 33 mV for a temperature difference of about 30 degree Celsius across the stack at resonance. Further investigations are underway to establish structure-performance relationships by extracting scaling laws for power-to-volume ratio and frequency-thermal gradient dependencies.more » « less
-
more » « less
Abstract The acoustic properties of an acoustic crystal consisting of acoustic channels designed according to the gyroid minimal surface embedded in a 3D rigid material are investigated. The resulting gyroid acoustic crystal is characterized by a spin‐1 Weyl and a charge‐2 Dirac degenerate points that are enforced by its nonsymmorphic symmetry. The gyroid geometry and its symmetries produce multi‐fold topological degeneracies that occur naturally without the need for ad hoc geometry designs. The non‐trivial topology of the acoustic dispersion produces chiral surface states with open arcs, which manifest themselves as waves whose propagation is highly directional and remains confined to the surfaces of a 3D material. Experiments on an additively manufactured sample validate the predictions of surface arc states and produce negative refraction of waves at the interface between adjoining surfaces. The topological surface states in a gyroid acoustic crystal shed light on nontrivial bulk and edge physics in symmetry‐based compact continuum materials, whose capabilities augment those observed in ad hoc designs. The continuous shape design of the considered acoustic channels and the ensuing anomalous acoustic performance suggest this class of phononic materials with semimetal‐like topology as effective building blocks for acoustic liners and load‐carrying structural components with sound proofing functionality.
-
Purpose AlSi10Mg alloy is commonly used in laser powder bed fusion due to its printability, relatively high thermal conductivity, low density and good mechanical properties. However, the thermal conductivity of as-built materials as a function of processing (energy density, laser power, laser scanning speed, support structure) and build orientation, are not well explored in the literature. This study aims to elucidate the relationship between processing, microstructure, and thermal conductivity. Design/methodology/approach The thermal conductivity of laser powder bed fusion (L-PBF) AlSi10Mg samples are investigated by the flash diffusivity and frequency domain thermoreflectance (FDTR) techniques. Thermal conductivities are linked to the microstructure of L-PBF AlSi10Mg, which changes with processing conditions. The through-plane exceeded the in-plane thermal conductivity for all energy densities. A co-located thermal conductivity map by frequency domain thermoreflectance (FDTR) and crystallographic grain orientation map by electron backscattered diffraction (EBSD) was used to investigate the effect of microstructure on thermal conductivity. Findings The highest through-plane thermal conductivity (136 ± 2 W/m-K) was achieved at 59 J/mm 3 and exceeded the values reported previously. The in-plane thermal conductivity peaked at 117 ± 2 W/m-K at 50 J/mm 3 . The trend of thermal conductivity reducing with energy density at similar porosity was primarily due to the reduced grain size producing more Al-Si interfaces that pose thermal resistance. At these interfaces, thermal energy must convert from electrons in the aluminum to phonons in the silicon. The co-located thermal conductivity and crystallographic grain orientation maps confirmed that larger colonies of columnar grains have higher thermal conductivity compared to smaller columnar grains. Practical implications The thermal properties of AlSi10Mg are crucial to heat transfer applications including additively manufactured heatsinks, cold plates, vapor chambers, heat pipes, enclosures and heat exchangers. Additionally, thermal-based nondestructive testing methods require these properties for applications such as defect detection and simulation of L-PBF processes. Industrial standards for L-PBF processes and components can use the data for thermal applications. Originality/value To the best of the authors’ knowledge, this paper is the first to make coupled thermal conductivity maps that were matched to microstructure for L-PBF AlSi10Mg aluminum alloy. This was achieved by a unique in-house thermal conductivity mapping setup and relating the data to local SEM EBSD maps. This provides the first conclusive proof that larger grain sizes can achieve higher thermal conductivity for this processing method and material system. This study also shows that control of the solidification can result in higher thermal conductivity. It was also the first to find that the build substrate (with or without support) has a large effect on thermal conductivity.more » « less
-
more » « less
Abstract A simple and facile method was developed to fabricate functional bulk barium titanate (BaTiO3,
BT ) ceramics using the paste extrusion 3D printing technique. TheBT ceramic is a lead‐free ferroelectric material widely used for various applications in sensors, energy storage, and harvesting. There are several traditional methods (eg, tape casting) to process bulkBT ceramics but they have disadvantages such as difficult handing without shape deformation, demolding, complex geometric shapes, expansive molds, etc. In this research, we utilized the paste extrusion 3D printing technique to overcome the traditional issues and developed printable ceramic suspensions containingBT ceramic powder, polyvinylidene fluoride (PVDF ), N,N‐dimethylformamide (DMF ) through simple mixing method and chemical formulation. ThisPVDF solution erformed multiple roles of binder, plasticizer, and dispersant for excellent manufacturability while providing high volume percent and density of the final bulk ceramic. Based on empirical data, it was found that the maximum binder ratio with good viscosity and retention for desired geometry is 1:8.8, while the maximumBT content is 35.45 vol% (77.01 wt%) in order to achieve maximum density of 3.93 g/cm3(65.3%) for 3D printedBT ceramic. Among different sintering temperatures, it was observed that the sinteredBT ceramic at 1400°C had highest grain growth and tetragonality which affected high performing piezoelectric and dielectric properties, 200 pC/N and 4730 at 103 Hz respectively. This paste extrusion 3D printing technique and simple synthesis method for ceramic suspensions are expected to enable rapid massive production, customization, design flexibility of the bulk piezoelectric and dielectric devices for next generation technology.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3397/IN-2021-2683
