An official website of the United States government
To maximize the capabilities of minimally invasive implantable bioelectronic devices, we must deliver large amounts of power to small implants; however, as devices are made smaller, it becomes more difficult to transfer large amounts of power without a wired connection. Indeed, recent work has explored creative wireless power transfer (WPT) approaches to maximize power density [the amount of power transferred divided by receiver footprint area (length × width)]. Here, we analyzed a model for WPT using magnetoelectric (ME) materials that convert an alternating magnetic field into an alternating voltage. With this model, we identify the parameters that impact WPT efficiency and optimize the power density. We find that improvements in adhesion between the laminated ME layers, clamping, and selection of material thicknesses lead to a power density of 3.1 mW/mm2, which is over four times larger than previously reported for mm-sized wireless bioelectronic implants at a depth of 1 cm or more in tissue. This improved power density allows us to deliver 31 and 56 mW to 10 and 27-mm2 ME receivers, respectively. This total power delivery is over five times larger than similarly sized bioelectronic devices powered by radiofrequency electromagnetic waves, inductive coupling, ultrasound, light, capacitive coupling, or previously reported magnetoelectrics. This increased power density opens the door to more power-intensive bioelectronic applications that have previously been inaccessible using mm-sized battery-free devices.
more »
« less
Magnetoelectric Versus Inductive Power Delivery for Sub-mm Receivers
Most of the next-generation implantable medical devices that are targeting sub-mm scale form factors are entirely powered wirelessly. The most commonly used form of wireless power transfer for ultra-small receivers is inductive coupling and has been so for many decades. This might change with the advent of novel microfabricated magnetoelectric (ME) antennas which are showing great potential as high-frequency wireless powered receivers. In this paper, we compare these two wireless power delivery methods using receivers that operate at 2.52 GHz with a surface area of 0.043 mm2 . Measurement results show that the maximum achievable power transfer of a ME antenna outperforms that of an on-silicon coil by approximately 7 times for a Tx-Rx distance of 2.16 and 3.3 times for a Tx-Rx distance of 0.76 cm.
more »
« less
- Award ID(s):
- 2020624
- PAR ID:
- 10309890
- Date Published:
- Journal Name:
- 2021 IEEE MTT-S Wireless Power Transfer Conference (WPTC 2021)
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Wirelessly powered neural stimulation and recording system is crucially important for the long-term study of the animal behaviors for the treatment of chronic neuropathic diseases. Headstage based neural implant is one of the popular methods to stimulate the neurons. In this work, a homecage based wireless power transfer (WPT) system is developed to supply power to a 3-D printed headstage which consists of a receiver (RX) coil, a rectifier and a light-emitting diode (LED) for optogenetic stimulation. A multilayer transmitter (TX) coil is designed to provide power over the 28.5 cm × 18 cm homecage area. The proposed system is able to achieve a maximum of 41.7% efficiency at 5 cm distance through air media using less number of headstage resonators compared to the other state-of-the art works.more » « less
-
Realizing the vision of ubiquitous battery-free sensing has proven to be challenging, mainly due to the practical energy and range limitations of current wireless communication systems. To address this, we design the first wide-area and scalable backscatter network with multiple receivers (RX) and transmitters (TX) base units to communicate with battery-free sensor nodes. Our system circumvents the inherent limitations of backscatter systems--including the limited coverage area, frequency-dependent operability, and sensor node limitations in handling network tasks--by introducing several coordination techniques between the base units starting from a single RX-TX pair to networks with many RX and TX units. We build low-cost RX and TX base units and battery-free sensor nodes with multiple sensing modalities and evaluate the performance of the MultiScatter system in various deployments. Our evaluation shows that we can successfully communicate with battery-free sensor nodes across 23400 square feet of a two-floor educational complex using 5 RX and 20 TX units, costing $569. Also, we show that the aggregated throughput of the backscatter network increases linearly as the number of RX units and the network coverage grows.more » « less
-
null (Ed.)Wearable sensors are a topic of interest in medical healthcare monitoring due to their compact size and portability. However, providing power to the wearable sensors for continuous health monitoring applications is a great challenge. As the batteries are bulky and require frequent charging, the integration of the wireless power transfer (WPT) module into wearable and implantable sensors is a popular alternative. The flexible sensors benefit by being wirelessly powered, as it not only expands an individual’s range of motion, but also reduces the overall size and the energy needs. This paper presents the design, modeling, and experimental characterization of flexible square-shaped spiral coils with different scaling factors for WPT systems. The effects of coil scaling factor on inductance, capacitance, resistance, and the quality factor (Q-factor) are modeled, simulated, and experimentally validated for the case of flexible planar coils. The proposed analytical modeling is helpful to estimate the coil parameters without using the time-consuming Finite Element Method (FEM) simulation. The analytical modeling is presented in terms of the scaling factor to find the best-optimized coil dimensions with the maximum Q-factor. This paper also presents the effect of skin contact with the flexible coil in terms of the power transfer efficiency (PTE) to validate the suitability as a wearable sensor. The measurement results at 405 MHz show that when in contact with the skin, the 20 mm× 20 mm receiver (RX) coil achieves a 42% efficiency through the air media for a 10 mm distance between the transmitter (TX) and RX coils.more » « less
-
This work presents a fully battery-less and wireless (untethered) EEG readout cap. The powering system is equipped with a highly efficient and compact power transmitter mosaicked by an array of 8×11 Tx resonators in a certain pattern operating at the lowest ISM band of 6.78 MHz. The front-end’s power receiver block Rx includes multi-resonators mounted all-around an EEG cap that can be worn by a subject. Furthermore, considering the subject's head which could assume different positions, a well-designed positioning system and an intelligent feeding setup are developed to balance the efficiency drop due to misalignment and to involve the most associated resonators with the powering scenario with the potential of switching off the extraneous resonators that are not engaged with Transmit and Receive (Tx-Rx) power.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/WPTC51349.2021.9458201
