Fabrication of multiscale, multimaterial 3D structures at high resolution is difficult using current technologies. This is especially significant when working with mechanically weak hydrogels. Here, a new hybrid laser printing (HLP) technology is reported to print complex, multiscale, multimaterial, 3D hydrogel structures with microscale resolution. This technique utilizes sequential additive and subtractive modes of fabrication, that are typically considered as mutually exclusive due to differences in their material processing conditions. Further, compared to current laser writing systems that enforce stringent processing depth limits, HLP is shown to fabricate structures at any depth inside the material. As a proof‐of‐principle, a Mayan pyramid with embedded cube frame is printed using synthetic polyethylene glycol diacrylate (PEGDA) hydrogel. Printing of ready‐to‐use open‐well chips with embedded microchannels is also demonstrated using PEGDA and gelatin methacrylate (GelMA) hydrogels for potential applications in biomedical sciences. Next, HLP is used in additive–additive modes to print multiscale 3D structures spanning in size from centimeter to micrometers within minutes, which is followed by printing of 3D, multimaterial, multiscale structures using this technology. Overall, this work demonstrates that HLP's fabrication versatility can potentially offer a unique opportunity for a range of applications in optics and photonics, biomedical sciences, microfluidics, etc.
- NSF-PAR ID:
- 10312482
- Date Published:
- Journal Name:
- ACS Biomaterials Science & Engineering
- ISSN:
- 2373-9878
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Despite the impressive performance of recent marine robots, many of their components are non‐biodegradable or even toxic and may negatively impact sensitive ecosystems. To overcome these limitations, biologically‐sourced hydrogels are a candidate material for marine robotics. Recent advances in embedded 3D printing have expanded the design freedom of hydrogel additive manufacturing. However, 3D printing small‐scale hydrogel‐based actuators remains challenging. In this study, Free form reversible embedding of suspended hydrogels (FRESH) printing is applied to fabricate small‐scale biologically‐derived, marine‐sourced hydraulic actuators by printing thin‐wall structures that are water‐tight and pressurizable. Calcium‐alginate hydrogels are used, a sustainable biomaterial sourced from brown seaweed. This process allows actuators to have complex shapes and internal cavities that are difficult to achieve with traditional fabrication techniques. Furthermore, it demonstrates that fabricated components are biodegradable, safely edible, and digestible by marine organisms. Finally, a reversible chelation‐crosslinking mechanism is implemented to dynamically modify alginate actuators' structural stiffness and morphology. This study expands the possible design space for biodegradable marine robots by improving the manufacturability of complex soft devices using biologically‐sourced materials.
-
more » « less
Abstract Fiber‐filled composite materials offer a unique pathway to enable new functionalities for systems built via extrusion‐based additive manufacturing (or “3D printing”); however, challenges remain in controlling the fiber orientations that govern ultimate performance. In this work, a multi‐material, shape‐changing nozzle—constructed by means of PolyJet 3D printing—is presented that allows for the spatial distribution of short fibers embedded in polymer matrices to be modulated on demand throughout extrusion‐based deposition processes. Specifically, the nozzle comprises flexible bladders that can be inflated pneumatically to alter the geometry of the material extrusion channel from a straight to a converging–diverging configuration, and in turn, the directional orientation of fibers within printed filaments. Experimental results for printing carbon microfiber‐hydrogel composites reveal that increasing the nozzle actuation pressure from 0 to 100 kPa reduced the proportion of aligned fibers, and notably, prompted a transition from anisotropic to isotropic water‐induced swelling properties (i.e., the ratio of transverse to longitudinal swelling strain decreased from 1.73
± 0.37 to 0.93± 0.39, respectively). In addition, dynamically varying the nozzle geometry during the extrusion of continuous composite filaments effects distinct swelling behaviors in adjacent regions, suggesting potential utility of the presented approach for emerging “4D printing” applications. -
more » « less
Abstract A rapid and facile approach to predictably control integration between two materials with divergent properties is introduced. Programmed integration between photopolymerizable soft and stiff hydrogels is investigated due to their promise in applications such as tissue engineering where heterogeneous properties are often desired. The spatial control afforded by grayscale 3D printing is leveraged to define regions at the interface that permit diffusive transport of a second material in‐filled into the 3D printed part. The printing parameters (i.e., effective exposure dose) for the resin are correlated directly to mesh size to achieve controlled diffusion. Applying this information to grayscale exposures leads to a range of distances over which integration is achieved with high fidelity. A prescribed finite distance of integration between soft and stiff hydrogels leads to a 33% increase in strain to failure under tensile testing and eliminates failure at the interface. The feasibility of this approach is demonstrated in a layer‐by‐layer 3D printed part fabricated by stereolithography, which is subsequently infilled with a soft hydrogel containing osteoblastic cells. In summary, this approach holds promise for applications where integration of multiple materials and living cells is needed by allowing precise control over integration and reducing mechanical failure at contrasting material interfaces.
-
On‐Demand Programming of Liquid Metal‐Composite Microstructures through Direct Ink Write 3D Printingmore » « less
Abstract Soft, elastically deformable composites with liquid metal (LM) droplets can enable new generations of soft electronics, robotics, and reconfigurable structures. However, techniques to control local composite microstructure, which ultimately governs material properties and performance, is lacking. Here a direct ink writing technique is developed to program the LM microstructure (i.e., shape, orientation, and connectivity) on demand throughout elastomer composites. In contrast to inks with rigid particles that have fixed shape and size, it is shown that emulsion inks with LM fillers enable in situ control of microstructure. This enables filaments, films, and 3D structures with unique LM microstructures that are generated on demand and locked in during printing. This includes smooth and discrete transitions from spherical to needle‐like droplets, curvilinear microstructures, geometrically complex embedded inclusion patterns, and connected LM networks. The printed materials are soft (modulus < 200 kPa), highly deformable (>600 % strain), and can be made locally insulating or electrically conductive using a single ink by controlling the process conditions. These capabilities are demonstrated by embedding elongated LM droplets in a soft heat sink, which rapidly dissipates heat from high‐power LEDs. These programmable microstructures can enable new composite paradigms for emerging technologies that demand mechanical compliance with multifunctional response.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1021/acsbiomaterials.1c00908
