An official website of the United States government
Hydrogels are soft hydrated polymer networks that are widely used in research and industry due to their favorable properties and similarity to biological tissues. However, it has long been difficult to create a hydrogel emulating the heterogeneous structure of special tissues, such as cartilage. One potential avenue to develop a structural variation in a hydrogel is the “mold effect,” which has only recently been discovered to be caused by absorbed oxygen within the mold surface interfering with the polymerization. This induces a dilute gradient-density surface layer with altered properties. However, the precise structure of the gradient-surface layer and its contact response have not yet been characterized. Such knowledge would prove useful for designs of composite hydrogels with altered surface characteristics. To fully characterize the hydrogel gradient-surface layer, we created five hydrogel compositions of varying monomer and cross-linker content to encompass variations in the layer. Then, we used particle exclusion microscopy during indentation and creep experiments to probe the contact response of the gradient layer of each composition. These experiments showed that the dilute structure of the gradient layer follows evolving contact behavior allowing poroelastic squeeze-out at miniscule pressures. Stiffer compositions had thinner gradient layers. This knowledge can potentially be used to create hydrogels with a stiff load-bearing bulk with altered surface characteristics tailored for specific tribological applications.
more »
« less
Poroelastic shape relaxation of hydrogel particles
Hydrogels are commonly used in research and energy, manufacturing, agriculture, and biomedical applications. These uses typically require hydrogel mechanics and internal water transport, described by the poroelastic diffusion coefficient, to be characterized. Sophisticated indentation-based approaches are typically used for this purpose, but they require expensive instrumentation and are often limited to planar samples. Here, we present Sha pe Re laxation (SHARE), an alternative way to assess the poroelastic diffusion coefficient of hydrogel particles that is cost-effective, straightforward, and versatile. This approach relies on first indenting a hydrogel particle via swelling within a granular packing, and then monitoring how the indented shape of the hydrogel relaxes after it is removed from the packing. We validate this approach using experiments in packings with varying grain sizes and confining stresses; these yield measurements of the poroelastic diffusion coefficient of polyacrylamide hydrogels that are in good agreement with those previously obtained using indentation approaches. We therefore anticipate that the SHARE approach will find broad use in a range of applications of hydrogels and other swellable soft materials.
more »
« less
- Award ID(s):
- 2011750
- PAR ID:
- 10324976
- Date Published:
- Journal Name:
- Soft Matter
- Volume:
- 17
- Issue:
- 14
- ISSN:
- 1744-683X
- Page Range / eLocation ID:
- 3840 to 3847
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Haugh, Jason M (Ed.)We develop a computational algorithm based on a diffuse interface approach to study the design of bioartificial organ scaffold architectures. These scaffolds, composed of poroelastic hydrogels housing transplanted cells, are linked to the patient’s blood circulation via an anastomosis graft. Before entering the scaffold, the blood flow passes through a filter, and the resulting filtered blood plasma transports oxygen and nutrients to sustain the viability of transplanted cells over the long term. A key issue in maintaining cell viability is the design of ultrafiltrate channels within the hydrogel scaffold to facilitate advection-enhanced oxygen supply ensuring oxygen levels remain above a critical threshold to prevent hypoxia. In this manuscript, we develop a computational algorithm to analyze the plasma flow and oxygen concentration within hydrogels featuring various channel geometries. Our objective is to identify the optimal hydrogel channel architecture that sustains oxygen concentration throughout the scaffold above the critical hypoxic threshold. The computational algorithm we introduce here employs a diffuse interface approach to solve a multi-physics problem. The corresponding model couples the time-dependent Stokes equations, governing blood plasma flow through the channel network, with the time-dependent Biot equations, characterizing Darcy velocity, pressure, and displacement within the poroelastic hydrogel containing the transplanted cells. Subsequently, the calculated plasma velocity is utilized to determine oxygen concentration within the scaffold using a diffuse interface advection-reaction-diffusion model. Our investigation yields a scaffold architecture featuring a hexagonal network geometry that meets the desired oxygen concentration criteria. Unlike classical sharp interface approaches, the diffuse interface approach we employ is particularly adept at addressing problems with intricate interface geometries, such as those encountered in bioartificial organ scaffold design. This study is significant because recent developments in hydrogel fabrication make it now possible to control hydrogel rheology and utilize computational results to generate optimized scaffold architectures.more » « less
-
Bioremediation of chlorinated aliphatic hydrocarbon-contaminated aquifers can be hindered by high contaminant concentrations and acids generated during remediation. Encapsulating microbes in hydrogels may provide a protective, tunable environment from inhibiting compounds; however, current approaches to formulate successful encapsulated systems rely on trial and error rather than engineering approaches because fundamental information on mass-transfer coefficients is lacking. To address this knowledge gap, hydronium ion mass-transfer rates through two commonly used hydrogel materials, poly(vinyl alcohol) and alginic acid, under two solidification methods (chemical and cryogenic) were measured. Variations in hydrogel crosslinking conditions, polymer composition, and solvent ionic strength were investigated to understand how each influenced hydronium ion diffusivity. A three-way ANOVA indicated that the ionic strength, membrane type, and crosslinking method significantly (p < 0.001) contributed to changes in hydronium ion mass transfer. Hydronium ion diffusion increased with ionic strength, counter to what is observed in aqueous-only (no polymer) solutions. Co-occurring mechanisms correlated to increased hydronium ion diffusion with ionic strength included an increased water fraction within hydrogel matrices and hydrogel contraction. Measured diffusion rates determined in this study provide first principal design information to further optimize encapsulating hydrogels for bioremediation.more » « less
-
Boundary conditions between a porous solid and a fluid has been a long-standing problem in modeling porous media. For deformable poroelastic materials such as hydrogels, the question is further complicated by the elastic stress from the solid network. Recently, an interfacial permeability condition has been developed from the principle of positive energy dissipation on the hydrogel–fluid interface. Although this boundary condition has been used in flow computations and yielded reasonable predictions, it contains an interfacial permeability g as a phenomenological parameter. In this work, we use porescale models of flow into a periodic array of solid cylinders or parallel holes to determine g as a function of the pore size and porosity. This provides a means to evaluate the interfacial permeability for a wide range of poroelastic materials, including hydrogels, foams and biological tissues, to enable realistic flow simulations.more » « less
-
null (Ed.)Approaches to control the microstructure of hydrogels enable the control of cell–material interactions and the design of stimuli-responsive materials. We report a versatile approach for the synthesis of anisotropic polyacrylamide hydrogels using lyotropic chromonic liquid crystal (LCLC) templating. The orientational order of LCLCs in a mold can be patterned by controlling surface anchoring conditions, which in turn patterns the polymer network. The resulting hydrogels have tunable pore size and mechanical anisotropy. For example, the elastic moduli measured parallel and perpendicular to the LCLC order are 124.9 ± 6.4 kPa and 17.4 ± 1.1 kPa for a single composition. The resulting anisotropic hydrogels also have 30% larger swelling normal to the LCLC orientation than along the LCLC orientation. By patterning the LCLC order, this anisotropic swelling can be used to create 3D hydrogel structures. These anisotropic gels can also be functionalized with extracellular matrix (ECM) proteins and used as compliant substrata for cell culture. As an illustrative example, we show that the patterned hydrogel microstructure can be used to direct the orientation of cultured human corneal fibroblasts. This strategy to make anisotropic hydrogels has potential for enabling patternable tissue scaffolds, soft robotics, or microfluidic devices.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/D0SM02243H
