skip to main content


Title: Comparing energy demands and longevities of membrane-based capacitive deionization architectures
Several capacitive deionization (CDI) cell architectures employ ion-exchange membranes to control the chemistry of the electrolyte contacting the electrodes. Here, we experimentally examined how exposing carbon electrodes to either a saline electrolyte or an electrolyte containing a soluble redox-active compound influenced deionization energy demands and long-term stability over ∼50 hours. We specifically compared the energy demands (W h L −1 ) required to deionize 20 mM NaCl to 15 mM with a 50% water recovery as a function of productivity (L m −2 h −1 ). Relative to a conventional membrane capacitive deionization (MCDI) cell, flowing saline electrolyte over the electrodes did not affect energy demands but increased electrode salt adsorption capacities and capacity retention over repeated cycles. Exposing the electrodes to an electrolyte containing a redox-active compound, which made the cell behave similarly to an electrodialysis system, dramatically reduced energy demands and showed remarkable stability over 50 hours of operation. These experimental results indicate that using a recirculated soluble redox-active compound in the electrolyte contacting the electrodes to balance charge leads to far more energy efficient brackish water deionization than when charge is balanced by the electrodes undergoing capacitive charging/discharging reactions.  more » « less
Award ID(s):
1749207
NSF-PAR ID:
10340965
Author(s) / Creator(s):
;
Date Published:
Journal Name:
Environmental Science: Water Research & Technology
Volume:
8
Issue:
7
ISSN:
2053-1400
Page Range / eLocation ID:
1489 to 1496
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Hybrid capacitive deionization (HCDI), which combines a capacitive carbon electrode and a redox active electrode in a single device, has emerged as a promising method for water desalination, enabling higher ion removal capacity than devices containing two carbon electrodes. However, to date, the desalination performance of few redox active materials has been reported. For the first time, we present the electrochemical behavior of manganese oxide nanowires with four different tunnel crystal structures as faradaic electrodes in HCDI cells. Two of these phases are square tunnel structured manganese oxides, α-MnO2 and todorokite-MnO2. The other two phases have novel structures that cross-sectional scanning transmission electron microscopy analysis revealed to have ordered and disordered combinations of structural tunnels with different dimensions. The ion removal performance of the nanowires was evaluated not only in NaCl solution, which is traditionally used in laboratory experiments, but also in KCl and MgCl2 solutions, providing better understanding of the behavior of these materials for desalination of brackish water that contains multiple cation species. High ion removal capacities (as large as 27.8 mg g−1, 44.4 mg g−1, and 43.1 mg g−1 in NaCl, KCl, and MgCl2 solutions, respectively) and high ion removal rates (as large as 0.112 mg g−1 s−1, 0.165 mg g−1 s−1, and 0.164 mg g−1 s−1 in NaCl, KCl, and MgCl2 solutions, respectively) were achieved. By comparing ion removal capacity to structural tunnel size, it was found that smaller tunnels do not favor the removal of cations with larger hydrated radii, and more efficient removal of larger hydrated cations can be achieved by utilizing manganese oxides with larger structural tunnels. Extended HCDI cycling and ex situ X-ray diffraction analysis revealed the excellent stability of the manganese oxide electrodes in repeated ion removal/ion release cycles, and compositional analysis of the electrodes indicated that ion removal is achieved through both surface redox reactions and intercalation of ions into the structural tunnels. This work contributes to the understanding of the behavior of faradaic materials in electrochemical water desalination and elucidates the relationship between the electrode material crystal structure and the ion removal capacity/ion removal rate in various salt solutions. 
    more » « less
  2. Conventional lithium-ion batteries are unable to meet the increasing demands for high-energy storage systems, because of their limited theoretical capacity. 1 In recent years, intensive attention has been paid to enhancing battery energy storage capability to satisfy the increasing energy demand in modern society and reduce the average energy capacity cost. Among the candidates for next generation high energy storage systems, the lithium sulfur battery is especially attractive because of its high theoretical specific energy (around 2600 W h kg-1) and potential cost reduction. In addition, sulfur is a cost effective and environmentally friendly material due to its abundance and low-toxicity. 2 Despite all of these advantages, the practical application of lithium sulfur batteries to date has been hindered by a series of obstacles, including low active material loading, poor cycle life, and sluggish sulfur conversion kinetics. 3 Achieving high mass loading cathode in the traditional 2D planar thick electrode has been challenged. The high distorsion of the traditional planar thick electrodes for ion/electron transfer leads to the limited utilization of active materials and high resistance, which eventually results in restricted energy density and accelerated electrode failure. 4 Furthermore, of the electrolyte to pores in the cathode and utilization ratio of active materials. Catalysts such as MnO 2 and Co dopants were employed to accelerate the sulfur conversion reaction during the charge and discharge process. 5 However, catalysts based on transition metals suffer from poor electronic conductivity. Other catalysts such as transition metal dopants are also limited due to the increased process complexities. . In addition, the severe shuttle effects in Li-S batteries may lead to fast failures of the battery. Constructing a protection layer on the separator for limiting the transmission of soluble polysulfides is considered an effective way to eliminate the shuttle phenomenon. However, the soluble sulfides still can largely dissolve around the cathode side causing the sluggish reaction condition for sulfur conversion. 5 To mitigate the issues above, herein we demonstrate a novel sulfur electrode design strategy enabled by additive manufacturing and oxidative vapor deposition (oCVD). Specifically, the electrode is strategically designed into a hierarchal hollow structure via stereolithography technique to increase sulfur usage. The active material concentration loaded to the battery cathode is controlled precisely during 3D printing by adjusting the number of printed layers. Owing to its freedom in geometry and structure, the suggested design is expected to improve the Li ions and electron transport rate considerably, and hence, the battery power density. The printed cathode is sintered at 700 °C at N 2 atmosphere to achieve carbonization of the cathode during which intrinsic carbon defects (e.g., pentagon carbon) as catalytic defect sites are in-situ generated on the cathode. The intrinsic carbon defects equipped with adequate electronic conductivity. The sintered 3D cathode is then transferred to the oCVD chamber for depositing a thin PEDOT layer as a protection layer to restrict dissolutions of sulfur compounds in the cathode. Density functional theory calculation reveals the electronic state variance between the structures with and without defects, the structure with defects demonstrates the higher kinetic condition for sulfur conversion. To further identify the favorable reaction dynamic process, the in-situ XRD is used to characterize the transformation between soluble and insoluble polysulfides, which is the main barrier in the charge and discharge process of Li-S batteries. The results show the oCVD coated 3D printed sulfur cathode exhibits a much higher kinetic process for sulfur conversion, which benefits from the highly tailored hierarchal hollow structure and the defects engineering on the cathode. Further, the oCVD coated 3D printed sulfur cathode also demonstrates higher stability during long cycling enabled by the oCVD PEDOT protection layer, which is verified by an absorption energy calculation of polysulfides at PEDOT. Such modeling and analysis help to elucidate the fundamental mechanisms that govern cathode performance and degradation in Li-S batteries. The current study also provides design strategies for the sulfur cathode as well as selection approaches to novel battery systems. References: Bhargav, A., (2020). Lithium-Sulfur Batteries: Attaining the Critical Metrics. Joule 4 , 285-291. Chung, S.-H., (2018). Progress on the Critical Parameters for Lithium–Sulfur Batteries to be Practically Viable. Advanced Functional Materials 28 , 1801188. Peng, H.-J.,(2017). Review on High-Loading and High-Energy Lithium–Sulfur Batteries. Advanced Energy Materials 7 , 1700260. Chu, T., (2021). 3D printing‐enabled advanced electrode architecture design. Carbon Energy 3 , 424-439. Shi, Z., (2021). Defect Engineering for Expediting Li–S Chemistry: Strategies, Mechanisms, and Perspectives. Advanced Energy Materials 11 . Figure 1 
    more » « less
  3. Capacitive deionization (CDI) is an energy saving and environmentally friendly technology for water desalination. However, classical CDI is challenged by a low salt removal capacity. To improve the desalination capacity, electrode materials utilizing the battery mechanism for salt ion removal have emerged as a new direction more recently. In this work, we report a study of amorphous iron phosphate (FePO 4 ) as a promising electrode material for pseudocapacitive sodium ion removal. Sodium ions can be effectively, reversibly intercalated and de-intercalated upon its electrochemical reduction and oxidation, with an excellent sodium ion capacity under half-cell testing conditions. By assembling a hybrid CDI (HCDI) system utilizing the FePO 4 electrode for pseudocapacitive sodium ion removal and active carbon electrode for capacitive chloride ion removal, the cell exhibited a high salt removal capacity and good reversibility and durability, which was attributed to the advantageous features of amorphous FePO 4 . The HCDI system achieved a high deionization capacity (82 mg g −1 ) in 10 mM NaCl, a fast deionization rate (0.046 mg g −1 s −1 ), and good stability and cyclability. 
    more » « less
  4. Redox flow batteries are attractive for grid-scale energy storage, but ongoing work on materials discovery is hampered by the difficulty of measuring electron-transfer rates under battery-relevant conditions. We have developed an experimental approach for collecting continuous voltammetric measurements of flow battery electrolytes by placing a 3-electrode cell containing an ultramicroelectrode into the flow loop of a functioning redox flow battery. We further developed an empirical approach for extracting electron-transfer rate constants from each voltammetric cycle, thereby enabling continuous measurements as a function of state of charge and cycle time. Benchmarking these approaches with iron-based aqueous flow battery electrolytes using platinum and carbon fiber ultramicroelectrodes yielded rate constants that varied in the order Pt > electrochemically oxidized carbon > pristine carbon, in good agreement with prior work. We also found that Pt electrodes become more catalytically active upon cycling for several hours, whereas carbon fiber electrodes with and without oxidative pretreatments remained stable over the same interval. We expect these experimental approaches can be used to measure kinetics and other figures of merit for most electrodes and electrolytes of interest for redox flow batteries as well as in other systems where it is useful to evaluate the properties of a flowing electrolyte in real time. 
    more » « less
  5. Abstract

    Understanding the thermodynamics associated with ion mixing and separation processes is important in order to meet the rising demands for clean energy and water production. Several electrochemical-based technologies such as capacitive deionization and capacitive mixing (CapMix) are capable of achieving desalination and energy production through ion mixing and separation processes, yet experimental investigations suggest energy conversion occurs with low second law (thermodynamic) efficiency. Here, we explore the maximum attainable efficiency for different CapMix cycles to investigate the impact cycle operation has on energy extraction. All investigated cycles are analogous to well documented heat engine cycles. In order to analyze CapMix cycles, we develop a physics-based model of the electric double layer based on the Gouy-Chapman-Stern theory. Evaluating CapMix cycles for energy generation revealed that cycles where ion mixing occurs at constant concentration and switching occurs at constant charge (a cycle analogous to the Stirling engine) attained the highest overall first law (electrical energy) efficiency (39%). This first law efficiency is nearly 300% greater than the first law efficiency of the Otto, Diesel, Brayton, and Atkinson analog cycles where ion mixing occurs while maintaining a constant number of ions. Additionally, the maximum first law efficiency was 89% with a maximum work output of 0.5 kWh per m3 of solution mixed (V = 1.0V) using this same Stirling cycle. Here the salinity gradient was CH = 600 mM and CL = 1 mM (ΔGmix = 0.56 kWh/m3). The effect of voltage was also examined at CH = 600 mM (seawater) and CL = 20 mM (river water). CapMix cycles operated at lower voltage (V < 1.0V), resulted in the Otto cycle yielding the highest first law efficiency of approximately 25% (compared to under 20% for the Stirling cycle); however, this was at the expense of a reduction (50x) in net electrical energy extracted from the same mixing process (0.01 kWh per m3).

     
    more » « less