skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Sustainable power generation via hydro-electrochemical effects
Recent efforts towards energy scavenging with eco-friendly methods and abundant water look very promising for powering wearables and distributed electronics. However, the time duration of electricity generation is typically too short, and the current level is not sufficient to meet the required threshold for the proper operation of electronics despite the relatively large voltage. This work newly introduced an electrochemical method in combination with hydro-effects in order to extend the energy scavenging time and boost the current. Our device consists of corroded porous steel electrodes whose corrosion overpotential was lowered when the water concentration was increased and vice versa . Then a potential difference was created between two electrodes, generating electricity via the hydro-electrochemical method up to an open-circuit voltage of 750 mV and a short-circuit current of 90 μA cm −2 . Furthermore, electricity was continuously generated for more than 1500 minutes by slow water diffusion against gravity from the bottom electrode. Lastly, we demonstrated that our hydro-electrochemical power generators successfully operated electronics, showing the feasibility of offering electrical power for sufficiently long time periods in practice.  more » « less
Award ID(s):
1805963
PAR ID:
10344386
Author(s) / Creator(s):
; ; ;
Date Published:
Journal Name:
Nanoscale
Volume:
14
Issue:
11
ISSN:
2040-3364
Page Range / eLocation ID:
4188 to 4194
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Nature Communications)
    Abstract Thermoelectrics are suited to converting dissipated heat into electricity for operating electronics, but the small voltage (~0.1 mV K−1) from the Seebeck effect has been one of the major hurdles in practical implementation. Here an approach with thermo-hydro-electrochemical effects can generate a large thermal-to-electrical energy conversion factor (TtoE factor), −87 mV K−1with low-cost carbon steel electrodes and a solid-state polyelectrolyte made of polyaniline and polystyrene sulfonate (PANI:PSS). We discovered that the thermo-diffusion of water in PANI:PSS under a temperature gradient induced less (or more) water on the hotter (or colder) side, raising (or lowering) the corrosion overpotential in the hotter (or colder) side and thereby generating output power between the electrodes. Our findings are expected to facilitate subsequent research for further increasing the TtoE factor and utilizing dissipated thermal energy. 
    more » « less
  2. ; ; ; ; (, SPIE Defense + Commercial Sensing)
    Dutta, Achyut K.; Balaya, Palani; Xu, Sheng (Ed.)
    Monitoring human health in real-time using wearable and implantable electronics (WIE) has become one of the most promising and rapidly growing technologies in the healthcare industry. In general, these electronics are powered by batteries that require periodic replacement and maintenance over their lifetime. To prolong the operation of these electronics, they should have zero post-installation maintenance. On this front, various energy harvesting technologies to generate electrical energy from ambient energy sources have been researched. Many energy harvesters currently available are limited by their power output and energy densities. With the miniaturization of wearable and implantable electronics, the size of the harvesters must be miniaturized accordingly in order to increase the energy density of the harvesters. Additionally, many of the energy harvesters also suffer from limited operational parameters such as resonance frequency and variable input signals. In this work, low frequency motion energy harvesting based on reverse electrowetting-ondielectric (REWOD) is examined using perforated high surface area electrodes with 38 µm pore diameters. Total available surface area per planar area was 8.36 cm2 showing a significant surface area enhancement from planar to porous electrodes and proportional increase in AC voltage density from our previous work. In REWOD energy harvesting, high surface area electrodes significantly increase the capacitance and hence the power density. An AC peak-to-peak voltage generation from the electrode in the range from 1.57-3.32 V for the given frequency range of 1-5 Hz with 0.5 Hz step is demonstrated. In addition, the unconditioned power generated from the harvester is converted to a DC power using a commercial off-theshelf Schottky diode-based voltage multiplier and low dropout regulator (LDO) such that the sensors that use this technology could be fully self-powered. The produced charge is then converted to a proportional voltage by using a commercial charge amplifier to record the features of the motion activities. A transceiver radio is also used to transmit the digitized data from the amplifier and the built-in analog-to-digital converter (ADC) in the micro-controller. This paper proposes the energy harvester acting as a self-powered motion sensor for different physical activities for wearable and wireless healthcare devices. 
    more » « less
  3. ; ; ; ; (, Energy Advances)
    Electrochemical double-layer capacitors (EDLCs) provide high power density and long cycle life energy storage. This work examines the use of inexpensive, raw coal char as an electrode material for supercapacitors. The effect of electrolyte composition on the performance of coal char supercapacitors is explored for the first time to determine the relative contributions of double-layer capacitance vs. faradaic reactions on total charge storage. Six electrolytes are examined with coal char electrodes, including: four aqueous electrolytes (0.5 M H 2 SO 4 , 6 M KOH, 0.5 M Na 2 SO 4 , 4 M LiNO 3 ); a water-in-salt electrolyte using 13 m NaClO 4 ; and an ionic liquid electrolyte (1-butyl-3-methylimidazolium tetrafluoroborate in acetonitrile). Voltage range, specific capacitance, electrochemical impedance, and charge–discharge characteristics of the coal char in the different electrolytes are characterized. The results indicate that neutral aqueous, water-in-salt, and ionic liquid electrolytes present a charging/discharging process approaching ideal EDLC behavior. The study provides insight into the optimal electrolyte composition for use with coal char electrodes and contributes to the current understanding of electrode-electrolyte interactions in carbon supercapacitors. 
    more » « less
  4. ; ; ; ; (, Journal of chemical physics)
    Double heterojunction nanorods enable both electroluminescence and light harvesting capabilities within the same device structure, providing a promising platform for energy-scavenging displays and related applications. However, the efficiency of the photovoltaic mode remains modest for useful power conversion and may be challenging to improve without sacrificing performance in electroluminescence. Through a facile on-film partial ligand exchange with benzenethiol integrated into the device fabrication step, we achieve an average of more than threefold increase in power conversion efficiency while maintaining the maximum external quantum efficiency and the maximum luminance in the LED mode. The improved photovoltaic performance is mainly due to the increase in the short circuit current, which we attribute to the enhanced charge separation afforded by the partial ligand exchange. The recovery of the photoluminescence lifetime under the forward bias suggests that the hole traps introduced by benzenethiols are filled prior to reaching the voltage at which light emission begins, allowing LED performance to be maintained and possibly improved. 
    more » « less
  5. ; ; (, Small)
    Abstract For decades, science fiction has imagined electronic devices that spring to life on demand, function as programmed, and then vanish without a trace. Today, transient and bioresorbable electronics are making that vision a reality, sparking revolutionary progress in biomedicine, environmental stewardship, and hardware security. Yet one critical barrier remains: a fully transient power source with the same disappearing act. Microbial‐based biobatteries have emerged as strong contenders, harnessing the power of microorganisms—found virtually everywhere—as natural biocatalysts. However, toxicity and health risks have limited these systems to single‐use, often incinerable applications. Here, a transformative approach: a transient biobattery powered by commercially available probiotics that dissolves harmlessly is introduced, releasing only beneficial microbes. Fabricated on water‐soluble or pH‐responsive substrates, this biobattery capitalizes on a 15‐strain probiotic blend to generate electricity across diverse electrode materials. By manipulating device length or encapsulating it with pH‐sensitive polymers, power delivery can be fine‐tuned from 4 min up to over 100 min. A single module outputs 4 µW of power, 47 µA of current, and an open‐circuit voltage of 0.65 V. This groundbreaking design ushers in a new era of safe, effective transient bioenergy systems, opening unprecedented opportunities in biomedical implants, environmental sensors, and disposable electronics. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email