skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Pressure and Strain Measurement on a 10° Control Surface of a Slender Cone in Hypersonic Flow
This paper presents the results of an experimental technique to acquire full-field pressure and strain fields on the windward side of a 10° flap attached to a slender cone-slice model. Tests were conducted in the Hypersonic Wind Tunnel (M = 5, Re= 9 – 14×10^6/m, air) at Sandia National Laboratories. The flap was coated with a fast-response, pressure-sensitive paint sprayed over a photoelastic coating and located near the trailing-edge of an axial slice along the 7° slender cone. This experiment was part of a sponsored project to develop the two-coating luminescent measurement technique and apply to high-speed, fluid-structure interaction environments. Results using a low-speed micropolarizer camera with four polarization orientations show that the technique is sensitive to pressure and strain, measuring an increasing pressure and decreasing strain from leading- to trailing-edge over the surface of the flap. At the low Re condition, the pressure signal captures the separated region near the flap leading edge and compares well with schlieren and oil-film measurements, the latter on a 10° wedge. Aerodynamic heating during the run does affect the pressure signal, likely resulting in an overestimation of pressure. Results using a conventional high-speed camera with a single linear polarizer captures the first bending and torsional modes of vibration when the flap is excited by transient shutdown conditions; however, coupling is difficult to detect in the pressure response due to baseline noise and the slower temporal response of the pressure coating.  more » « less
Award ID(s):
1802994
PAR ID:
10346953
Author(s) / Creator(s):
; ; ; ; ; ;
Date Published:
Journal Name:
AIAA AVIATION Forum
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; (, The Journal of Experimental Biology)
    null (Ed.)
    ABSTRACT The clap-and-fling mechanism is a well-studied, unsteady lift generation mechanism widely used by flying insects and is considered obligatory for tiny insects flying at low to intermediate Reynolds numbers, Re . However, some aquatic zooplankters including some pteropod (i.e. sea butterfly) and heteropod species swimming at low to intermediate Re also use the clap-and-fling mechanism. These marine snails have extremely flexible, actively deformed, muscular wings which they flap reciprocally to create propulsive force, and these wings may enable novel lift generation mechanisms not available to insects, which have less flexible, passively deformed wings. Using high-speed stereophotogrammetry and micro-particle image velocimetry, we describe a novel cylindrical overlap-and-fling mechanism used by the pteropod species Cuvierina atlantica . In this maneuver, the pteropod's wingtips overlap at the end of each half-stroke to sequentially form a downward-opening cone, a cylinder and an upward-opening cone. The transition from downward-opening cone to cylinder produces a downward-directed jet at the trailing edges. Similarly, the transition from cylinder to upward-opening cone produces downward flow into the gap between the wings, a leading edge vortex ring and a corresponding sharp increase in swimming speed. The ability of this pteropod species to perform the cylindrical overlap-and-fling maneuver twice during each stroke is enabled by its slender body and highly flexible wings. The cylindrical overlap-and-fling mechanism observed here may inspire the design of new soft robotic aquatic vehicles incorporating highly flexible propulsors to take advantage of this novel lift generation technique. 
    more » « less
  2. ; (, Proceedings of the ASME 2022 Fluids Engineering Division Summer Meeting)
    Abstract An experimental study was undertaken to evaluate the power extraction of an airfoil undergoing large amplitude pitching and heaving using a trailing edge flapping motion for the application of energy harvesting for steady flow over the airfoil. The airfoil was a NACA0015 design, pitching at the 1/3 chord position, with an actively controlled trailing edge flap hinged at the 2/3 chord location (chord length of c = 150mm and aspect ratio AR = 2, however end plates were used to simulate a two-dimensional airfoil). Data were obtained over a range of wind speeds corresponding to Reynolds numbers in the 30,000–60,000 range in a low-speed wind tunnel with turbulence intensities below 2%. The results are characterized using the reduced frequency, k = fc/U∞ over the range of 0.04–0.08, where f is the oscillating frequency in Hz, and U∞ is the freestream velocity. The pitching and heaving amplitudes are θ0 = 70° and h0 = 0.6c respectively, with a phase delay of 90°. Two trailing edge motion profiles are presented, examining the relative phase of trailing edge flap to the pitching phase. For each motion, a positive and negative case are considered. This is a total of 4 trailing edge motion profiles. Trailing edge motion amplitudes of 20° and 40° are compared and results contrasted. Direct transient force measurements were used to obtain the cycle variation of induced aerodynamic loads (lift coefficient) as well as the power output and efficiency. Results are used to identify the influence of trailing edge flap oscillations on the overall performance for energy harvesting, with a maximum efficiency increase of 21.3% and corresponding cycle averaged heaving power coefficient increase of 29.9% observed as a result of trailing edge motion. 
    more » « less
  3. ; ; (, AIAA Journal)
    We evaluate two leading-edge-based dynamic stall-onset criteria (namely, the maximum magnitudes of the leading-edge suction parameter and the boundary enstrophy flux) for mixed and trailing-edge stall. These criteria have been shown to successfully predict the onset of leading-edge stall at Reynolds numbers of O(10^5), where the leading-edge suction drops abruptly. However, for mixed/trailing-edge stall, leading-edge suction tends to persist even when there is significant trailing-edge reversed flow and stall is underway, necessitating further investigation into the effectiveness of these criteria. Using wall-resolved large-eddy simulations and the unsteady Reynolds-averaged Navier–Stokes method, we simulate one leading-edge stall and three mixed/trailing-edge stall cases at Reynolds numbers of 200,000 and 300,000. We contrast the progression of flow features such as trailing-edge separation and vortex formation across different stall types and evaluate the stall-onset criteria relative to critical points in the flow. We find that the criteria nearly coincide with the instance of leading-edge suction collapse and are reached in advance of dynamic stall vortex formation and lift stall for all four cases. We conclude that the two criteria effectively signal dynamic stall onset in cases where the dynamic stall vortex plays a prominent role. 
    more » « less
  4. ; ; (, 2022 AIAA SciTech Meeting)
    We evaluate two leading-edge-based dynamic stall onset criteria, namely, the maximum magnitudes of the Leading Edge Suction Parameter and the Boundary Enstrophy Flux, for mixed and trailing-edge stall. These criteria have been shown to successfully predict the onset of leading-edge stall at Reynolds numbers >= O(10^5), where the leading-edge suction drops abruptly. However, for mixed/trailing-edge stall, leading-edge suction tends to persist even when there is significant trailing-edge reversed flow and stall is underway, necessitating further investigation of the effectiveness of these criteria. Using wall-resolved, large-eddy simulations and unsteady Reynolds-Averaged Navier-Stokes method, we simulate one leading-edge stall and three mixed/trailing-edge stall cases at Reynolds numbers 2x10^5 and 3x10^6. We contrast the progression of flow features such as trailing-edge separation and vortex formation across different stall types and evaluate the stall onset criteria relative to critical points in the flow. We find that the criteria nearly coincide with the instance of leading-edge suction collapse and are reached in advance of dynamic stall vortex formation and lift stall for all four cases. We conclude that the two criteria effectively signal dynamic stall onset in cases where the dynamic stall vortex plays a prominent role. 
    more » « less
  5. ; ; (, 55th AIAA Aerospace Sciences Meeting)
    We numerically examine the use of Gurney flap to modify the two-dimensional wake dynamics for lift enhancement on NACA 0000 (flat plate), 0006, 0012 and 0018 airfoils. Incompressible flows over the airfoils at different angles of attack are considered at Re = 1000. It is observed that the attachment of the Gurney flap at the trailing edge is able to enhance the lift force experienced by the airfoil appreciably with increase in Gurney flap height. The lift-to-drag ratio of the airfoils is also observed to increase at lower angles of attack. The lift spectra and airfoil wake are examined to reveal the effect of the Gurney flap on the formation of different characteristic wake modes and the associated change in the aerodynamic forces exerted on the airfoils. Based on the observations, we classify the resulting wakes into four distinct modes. The emergence of these modes (steady, 2S, P and 2P) are mapped over a wide range of angles of attack and Gurney flap heights for all four airfoils in consideration. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email