An official website of the United States government
Abstract Geological heterogeneity is abundant in crustal fault zones; however, its role in controlling the mechanical behaviour of faults is poorly constrained. Here, we present laboratory friction experiments on laterally heterogeneous faults, with patches of strong, rate-weakening quartz gouge and weak, rate-strengthening clay gouge. The experiments show that the heterogeneity leads to a significant reduction in strength and frictional stability in comparison to compositionally identical faults with homogeneously mixed gouges. We identify a combination of weakening effects, including smearing of the weak clay; differential compaction of the two gouges redistributing normal stress; and shear localization producing stress concentrations in the strong quartz patches. The results demonstrate that geological heterogeneity and its evolution can have pronounced effects on fault strength and stability and, by extension, on the occurrence of slow-slip transients versus earthquake ruptures and the characteristics of the resulting events, and should be further studied in lab experiments and earthquake source modelling.
more »
« less
Nanometric flow and earthquake instability
Abstract Fault zones accommodate relative motion between tectonic blocks and control earthquake nucleation. Nanocrystalline fault rocks are ubiquitous in “principal slip zones” indicating that these materials are determining fault stability. However, the rheology of nanocrystalline fault rocks remains poorly constrained. Here, we show that such fault rocks are an order of magnitude weaker than their microcrystalline counterparts when deformed at identical experimental conditions. Weakening of the fault rocks is hence intrinsic, it occurs once nanocrystalline layers form. However, it is difficult to produce “rate weakening” behavior due to the low measured stress exponent,n, of 1.3 ± 0.4 and the low activation energy,Q, of 16,000 ± 14,000 J/mol implying that the material will be strongly “rate strengthening” with a weak temperature sensitivity. Failure of the fault zone nevertheless occurs once these weak layers coalesce in a kinematically favored network. This type of instability is distinct from the frictional instability used to describe crustal earthquakes.
more »
« less
- PAR ID:
- 10360427
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Nature Communications
- Volume:
- 12
- Issue:
- 1
- ISSN:
- 2041-1723
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Geophysical and geological studies provide evidence for cyclic changes in fault‐zone pore fluid pressure that synchronize with or at least modulate slip events. A hypothesized explanation is fault valving arising from temporal changes in fault zone permeability. In our study, we investigate how the coupled dynamics of rate and state friction, along‐fault fluid flow, and permeability evolution can produce slow slip events. Permeability decreases with time, and increases with slip. Linear stability analysis shows that steady slip with constant fluid flow along the fault zone is unstable to perturbations, even for velocity‐strengthening friction with no state evolution, if the background flow is sufficiently high. We refer to this instability as the “fault valve instability.” The propagation speed of the fluid pressure and slip pulse, which scales with permeability enhancement, can be much higher than expected from linear pressure diffusion. Two‐dimensional simulations with spatially uniform properties show that the fault valve instability develops into slow slip events, in the form of aseismic slip pulses that propagate in the direction of fluid flow. We also perform earthquake sequence simulations on a megathrust fault, taking into account depth‐dependent frictional and hydrological properties. The simulations produce quasi‐periodic slow slip events from the fault valve instability below the seismogenic zone, in both velocity‐weakening and velocity‐strengthening regions, for a wide range of effective normal stresses. A separation of slow slip events from the seismogenic zone, which is observed in some subduction zones, is reproduced when assuming a fluid sink around the mantle wedge corner.more » « less
-
Abstract High fracture density in fault damage zones not only reduces the elastic stiffness of rocks but may also promote time‐dependent bulk deformation through the sliding of fracture and thus alter the stress in fault zones. On comparing the damage zones of the three faults in the Chelungpu fault system encountered in the Taiwan Chelungpu fault Drilling Project (TCDP), the youngest damage zone showed pronounced sonic velocity reduction even though fracture density is the same for all three fault zones, consistent with the shorter time for velocity recovery in the youngest fault. Caliper log data showed a time‐dependent enlargement of the borehole wall at the damage zone. These damage zones record lower differential stress than the surrounding host rock, which cannot be explained by the reduced elastic stiffness in the damage zone. Stress relaxation caused by time‐dependent bulk deformation in the damage zone may be responsible for the observed low differential stress.more » « less
-
Abstract During rock friction experiments at large displacement, room temperature and humidity, and following a hold test, the fracture energy increases approximately as the square of the logarithm of hold duration. While it's been long known that failure strength increases with log hold time, here the slip weakening distance,dh, also increases. The weakening distance increase is large, hundreds of percent change over a few thousand seconds. The initial bare surface and simulated fault gouge experiments were conducted in rotary shear at 25 MPa normal stress, 21 MPa confining stress and at displacements greater than 100 mm. In contrast, initially bare surface experiments at 5 MPa normal stress, unconfined at displacements less than 10 mm show effectively no change indh. We attribute the difference to the presence of an appreciable shear zone that develops due to wear over significant displacements, confined at elevated normal stress. Prior published studies of sheared simulated fault gouge at short displacement show both acknowledged and unacknowledged increases indhthat may relate to our observations. Since natural faults have well‐developed shear zones, the observations have more direct relevance to earthquake nucleation than prior laboratory studies that use short displacement data and focus on frictional strength recovery alone. However, the physics underlying this increase in weakening distance are not known; candidates are compaction (Nakatani, 1998) and delocalization (Sleep et al., 2000). Additional caveats are that these are room temperature and humidity experiments, at a single normal stress that have not yet been reproduced in other laboratories.more » « less
-
Abstract The empirical rate‐ and state‐dependent friction law is widely used to explain the frictional resistance of rocks. However, the constitutive parameters vary with temperature and sliding velocity, preventing extrapolation of laboratory results to natural conditions. Here, we explain the frictional properties of natural gouge from the San Andreas Fault, Alpine Fault, and the Nankai Trough from room temperature to ∼300°C for a wide range of slip‐rates with constant constitutive parameters by invoking the competition between two healing mechanisms with different thermodynamic properties. A transition from velocity‐strengthening to velocity‐weakening at steady‐state can be attained either by decreasing the slip‐rate or by increasing temperature. Our study provides a framework to understand the physics underlying the slip‐rate and state dependence of friction and the dependence of frictional properties on ambient physical conditions.more » « less
