More Like this

1. Block Copolymer-Assisted Synthesis of Iron Oxide Nanoparticles for Effective Removal of Congo Red

   https://doi.org/10.3390/molecules28041914  

   Bhattarai, Mohan K.; Ashie, Moses D.; Dugu, Sita; Subedi, Kiran; Bastakoti, Bishnu P.; Morell, Gerardo; Katiyar, Ram S. (February 2023, Molecules)

   Iron oxide nanoparticles (IONPs) were synthesized via a block copolymer-assisted hydrothermal method and the phase purity and the crystal structure were investigated by X-ray diffraction. The Rietveld analysis of X-ray diffractometer spectra shows the hexagonal phase symmetry of α-Fe2O3. Further, the vibrational study suggests Raman active modes: 2A1g + 5Eg associated with α-Fe2O3, which corroborates the Rietveld analysis and orbital analysis of 2PFe. The superparamagnetic behavior is confirmed by magnetic measurements performed by the physical properties measurement system. The systematic study of the Congo red (CR) interaction with IONPs using a UV-visible spectrophotometer and a liquid chromatography–tandem mass spectrometry system equipped with a triple quadrupole mass analyzer and an electrospray ionization interface shows effective adsorption. In visible light, the Fe2O3 nanoparticles get easily excited and generate electrons and holes. The photogenerated electrons reduce the Fe3+ ions to Fe2+ ions. The Fe2+/H2O2 oxidizes CR by the Fenton mechanism. The strong adsorption ability of prepared nanoparticles towards dyes attributes the potential candidates for wastewater treatment and other catalytic applications. 

   more » « less
2. Ultrasound-Assisted Photocatalytic Degradation of Azo Dyes under Visible Light Irradiation Using Polythiophene-Decorated CoFe2O4 Nanohybrids

   https://doi.org/10.3390/catal14080495  

   Hauser, Kristen; Hassou, Sara Ou; Riaz, Ufana (August 2024, Catalysts)

   The present work reports the synthesis of cobalt ferrite and its nanohybrids with polythiophene (PTh) in the weight ratios of 10% and 20%. The ferrite and its nanohybrids were characterized using thermogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy coupled with elemental mapping (Fe-SEM) to confirm the morphology as well as the structure of the synthesized nanohybrids. The nanohybrids were tested for their photocatalytic activity upon modification of PTh against Alizarin Yellow (AY), Congo Red (CR) and Brilliant Blue (BB). Almost 100% degradation was achieved in 30 min using 50 mg of the photocatalyst. The effect of catalyst concentration and dye concentration was also investigated to explore optimum concentration of the photocatalyst required for rapid degradation of the dye. The generation of radicals responsible for degradation was analyzed by radical scavenging experiments and a probable mechanism of degradation was proposed. 

   more » « less
3. Electrophoretic deposition of iron oxide nanoparticles to achieve thick nickel/iron oxide magnetic nanocomposite films

   https://doi.org/10.1063/1.5129797  

   Mills, Sara_C; Smith, Connor_S; Arnold, David_P; Andrew, Jennifer_S (January 2020, AIP Advances)

   For modern switching power supplies, current bulk magnetic materials, such as ferrites or magnetic metal alloys, cannot provide both low loss and high magnetic saturation to function with both high power density and high efficiency at high frequencies (10-100 MHz). Magnetic nanocomposites comprised of a ferrite and magnetic metal alloy provide the opportunity to achieve these desired magnetic properties, but previously investigated thin-film fabrication techniques have difficulty achieving multi-micrometer film thicknesses which are necessary to provide practical magnetic energy storage and power handling. Here, we present a versatile technique to fabricate thick magnetic nanocomposites via a two-step process, consisting of the electrophoretic deposition of an iron oxide nanoparticle phase into a mold on a substrate, followed by electro-infiltration of a nickel matrix. The deposited films are imaged via scanning electron microscopy and energy dispersive X-ray spectroscopy to identify the presence of iron and nickel, confirming the infiltration of the nickel between the iron oxide nanoparticles. A film thickness of ∼7 μm was measured via stylus profilometry. Further confirmation of successful composite formation is obtained with vibrating sample magnetometry, showing the saturation magnetization value of the composite (473 kA/m) falls between that of the iron oxide nanoparticles (280 kA/m) and the nickel matrix (555 kA/m). These results demonstrate the potential of electrophoretic deposition coupled with electro-infiltration to fabricate magnetic nanocomposite films. 

   more » « less
4. Chemical State of Potassium on the Surface of Iron Oxides: Effects of Potassium Precursor Concentration and Calcination Temperature

   https://doi.org/10.3390/ma15207378  

   Hoque, Md. Ariful; Guzman, Marcelo I.; Selegue, John P.; Gnanamani, Muthu Kumaran (October 2022, Materials)

   Potassium is used extensively as a promoter with iron catalysts in Fisher–Tropsch synthesis, water–gas shift reactions, steam reforming, and alcohol synthesis. In this paper, the identification of potassium chemical states on the surface of iron catalysts is studied to improve our understanding of the catalytic system. Herein, potassium-doped iron oxide (α-Fe2O3) nanomaterials are synthesized under variable calcination temperatures (400–800 °C) using an incipient wetness impregnation method. The synthesis also varies the content of potassium nitrate deposited on superfine iron oxide with a diameter of 3 nm (Nanocat®) to reach atomic ratios of 100 Fe:x K (x = 0–5). The structure, composition, and properties of the synthesized materials are investigated by X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, Fourier-transform infrared, Raman spectroscopy, inductively coupled plasma-atomic emission spectroscopy, and X-ray photoelectron spectroscopy, as well as transmission electron microscopy, with energy-dispersive X-ray spectroscopy and selected area electron diffraction. The hematite phase of iron oxide retains its structure up to 700 °C without forming any new mixed phase. For compositions as high as 100 Fe:5 K, potassium nitrate remains stable up to 400 °C, but at 500 °C, it starts to decompose into nitrites and, at only 800 °C, it completely decomposes to potassium oxide (K2O) and a mixed phase, K2Fe22O34. The doping of potassium nitrate on the surface of α-Fe2O3 provides a new material with potential applications in Fisher–Tropsch catalysis, photocatalysis, and photoelectrochemical processes. 

   more » « less
5. Direct Ink Writing of Polymer Composite Electrolytes with Enhanced Thermal Conductivities

   https://doi.org/10.1002/adfm.202006683  

   Cheng, Meng; Ramasubramanian, Ajaykrishna; Rasul, Md_Golam; Jiang, Yizhou; Yuan, Yifei; Foroozan, Tara; Deivanayagam, Ramasubramonian; Tamadoni_Saray, Mahmoud; Rojaee, Ramin; Song, Boao; et al (October 2020, Advanced Functional Materials)

   Abstract Proper distribution of thermally conductive nanomaterials in polymer batteries offers new opportunities to mitigate performance degradations associated with local hot spots and safety concerns in batteries. Herein, a direct ink writing (DIW) method is utilized to fabricate polyethylene oxide (PEO) composite polymers electrolytes (CPE) embedded with silane‐treated hexagonal boron nitride (S‐hBN) platelets and free of any volatile organic solvents. It is observed that the S‐hBN platelets are well aligned in the printed CPE during the DIW process. The in‐plane thermal conductivity of the printed CPE with the aligned S‐hBN platelets is 1.031 W⁻¹K⁻¹, which is about 1.7 times that of the pristine CPE with the randomly dispersed S‐hBN platelets (0.612 W⁻¹K⁻¹). Thermal imaging shows that the peak temperature (°C) of the printed electrolytes is 24.2% lower than that of the CPE without S‐hBN, and 10.6% lower than that of the CPE with the randomly dispersed S‐hBN, indicating a superior thermal transport property. Lithium‐ion half‐cells made with the printed CPE and LiFePO₄cathode displayed high specific discharge capacity of 146.0 mAh g⁻¹and stable Coulombic efficiency of 91% for 100 cycles at room temperature. This work facilitates the development of printable thermally‐conductive polymers for safer battery operations. 

   more » « less