An official website of the United States government
In this article, we present the design of a powered knee–ankle prosthetic leg, which implements high-torque actuators with low-reduction transmissions. The transmission coupled with a high-torque and low-speed motor creates an actuator with low mechanical impedance and high backdrivability. This style of actuation presents several possible benefits over modern actuation styles in emerging robotic prosthetic legs, which include free-swinging knee motion, compliance with the ground, negligible unmodeled actuator dynamics, less acoustic noise, and power regeneration. Benchtop tests establish that both joints can be backdriven by small torques ( ∼ 1–3 N ⋅ m) and confirm the small reflected inertia. Impedance control tests prove that the intrinsic impedance and unmodeled dynamics of the actuator are sufficiently small to control joint impedance without torque feedback or lengthy tuning trials. Walking experiments validate performance under the designed loading conditions with minimal tuning. Finally, the regenerative abilities, low friction, and small reflected inertia of the presented actuators reduced power consumption and acoustic noise compared to state-of-the-art powered legs.
more »
« less
Inertialess gyrating engines
Abstract A typical model for a gyrating engine consists of an inertial wheel powered by an energy source that generates an angle-dependent torque. Examples of such engines include a pendulum with an externally applied torque, Stirling engines, and the Brownian gyrating engine. Variations in the torque are averaged out by the inertia of the system to produce limit cycle oscillations. While torque generating mechanisms are also ubiquitous in the biological world, where they typically feed on chemical gradients, inertia is not a property that one naturally associates with such processes. In the present work, seeking ways to dispense of the need for inertial effects, we study an inertia-less concept where the combined effect of coupled torque-producing components averages out variations in the ambient potential and helps overcome dissipative forces to allow sustained operation for vanishingly small inertia. We exemplify this inertia-less concept through analysis of two of the aforementioned engines, the Stirling engine, and the Brownian gyrating engine. An analogous principle may be sought in biomolecular processes as well as in modern-day technological engines, where for the latter, the coupled torque-producing components reduce vibrations that stem from the variability of the generated torque.
more »
« less
- PAR ID:
- 10381973
- Publisher / Repository:
- Oxford University Press
- Date Published:
- Journal Name:
- PNAS Nexus
- Volume:
- 1
- Issue:
- 5
- ISSN:
- 2752-6542
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Calibration of automotive engines to ensure compliance with emission regulations is a critical phase in product development. Control of engine-out particulate emissions, which directly impact the environment and public health, is particularly important. Detailed physics-based models are typically used to gain a rich understanding of the complex physical phenomena that drive the soot particle formation in an engine cylinder. However, such models often fail to correctly represent the highly dynamic nature of the underlying mechanisms under transient combustion conditions. Moreover, most physics-based models were initially developed for diesel engine applications and their applicability to gasoline engines remains questionable due to differences in flame structure and fuel-wall interactions. Black-box models have been previously proposed to predict engine-out soot emissions, but their lack of physical interpretability is an unsolved drawback. To address these limitations, we present a physics-aware twin-model machine learning framework to predict and analyze engine-out soot mass from a gasoline direct injection (GDI) engine. The framework combines a physics-based model with a bagging-type ensemble learning model that both maintains high accuracy and allows physical interpretation of results without using computationally intensive high-fidelity models. This work shows why a one-model-fits-all approach fails in the case of predicting soot emissions due to clustered co-occurrences of operating conditions that cause non-compliant behavior. We compare the performance of the proposed framework with that of the standalone baseline model and a feed-forward deep neural network. Using WLTP data from a 2.0L naturally aspirated GDI engine, the proposed framework predicts engine-out soot mass with an improvement of 29% in the R2 value and 21% in the root mean squared error from the baseline physics-based model, without compromising physical interpretability. These improvements are significant enough to warrant further framework development with additional engine datasets.more » « less
-
Fast-frequency control strategies have been proposed in the literature to maintain inertial response of electric generation and help with the frequency regulation of the system. However, it is challenging to deploy such strategies when the inertia constant of the system is unknown and time-varying. In this paper, we present a data-driven system identification approach for an energy storage system (ESS) operator to identify the inertial response of the system (and consequently the inertia constant). The method is first tested and validated with a simulated genset model using small changes in the system load as the excitation signal and measuring the corresponding change in frequency. The validated method is then used to experimentally identify the inertia constant of a genset. The inertia constant of the simulated genset model was estimated with an error of less than 5% which provides a reasonable estimate for the ESS operator to properly tune the parameters of a fast-frequency controller.more » « less
-
Modern web browsers rely on layout engines to convert HTML documents to layout trees that specify color, size, and position. However, existing layout engines are notoriously difficult to maintain because of the complexity of web standards. This is especially true for incremental layout engines, which are designed to improve performance by updating only the parts of the layout tree that need to be changed. In this paper, we propose Medea, a new framework for automatically generating incremental layout engines. Medea separates the specification of the layout engine from its incremental implementation, and guarantees correctness through layout engine synthesis. The synthesis is driven by a new iterative algorithm based on detecting conflicts that prevent optimality of the incremental algorithm. We evaluated Medea on a fragment of HTML layout that includes challenging features such as margin collapse, floating layout, and absolute positioning. Medea successfully synthesized an incremental layout engine for this fragment. The synthesized layout engine is both correct and efficient. In particular, we demonstrated that it avoids real-world bugs that have been reported in the layout engines of Chrome, Firefox, and Safari. The incremental layout engine synthesized by Medea is up to 1.82× faster than a naive incremental baseline. We also demonstrated that our conflict-driven algorithm produces engines that are 2.74× faster than a baseline without conflict analysis.more » « less
-
We propose a design paradigm for multistate machines where transitions from one state to another are organized by bifurcations of multiple equilibria of the energy landscape describing the collective interactions of the machine components. This design paradigm is attractive since, near bifurcations, small variations in a few control parameters can result in large changes to the system’s state providing an emergent lever mechanism. Further, the topological configuration of transitions between states near such bifurcations ensures robust operation, making the machine less sensitive to fabrication errors and noise. To design such machines, we develop and implement a new efficient algorithm that searches for interactions between the machine components that give rise to energy landscapes with these bifurcation structures. We demonstrate a proof of concept for this approach by designing magnetoelastic machines whose motions are primarily guided by their magnetic energy landscapes and show that by operating near bifurcations we can achieve multiple transition pathways between states. This proof of concept demonstration illustrates the power of this approach, which could be especially useful for soft robotics and at the microscale where typical macroscale designs are difficult to implement.more » « less
