The raw data for the associated manuscript is organized here into three categories: 1) relating to the measurement and analysis of the native recluse spiders loop junctions, 2) raw images found in the figures throughout the manuscript, and 3) relating to the experiments testing the effect that junction angle has on the strength of two intersecting tapes. It is recommended to browse the data files in Tree mode, which will make the files appear in folders reflecting this organization. 1) Loxosceles Loop Junction Images and Analysis The folder titled, SEM Raw Images, has all of the scanning electron microscopy (SEM) images taken of the native recluse loop junctions. Some images are close-ups of individual junctions and others take a broader perspective (macro) of many loop junctions in series. Where possible several close-up images of the individual junctions are accompanied with a macro image. These images were imported into ImageJ where the junction angle was measured. The measurements for all 41 loop junctions observed are in the folder titled, Raw Data Files in the file titled, Loxosceles Loop Junction Angle Measurements.txt. The folder titled, Raw Data Files contains, in addition to the angle measurements, the raw data for analyzing the strength of individual loop junctions. The data is in native MATLAB data format. These datasets include the complete tensile data and the cross-sectional area data for each spiders silk. The MATLAB code titled, Figure_2A_2B_code, processes the raw tensile data from the natural recluse spiders loop junctions. This data is plotted as two representative curves in Figure 2A and as a complete set as a histogram in Figure 2B. The MATLAB code titled, Figure_7_code, processes and plots the loop junction data found in, Loxosceles Loop Junction Angle Measurements.txt and executed the model of a random set of recluse loops. This code can be executed to generate Figure 7. The folder titled, Raw Data Files, must be open in MATLAB to run this code! This code uses the MATLAB function, areacalculation, to calculate the junction area for a given junction angle. 2) Raw Images This folder is organized by the respective figure in the manuscript where each image can be found. Additional metadata for each image can be found accompanying each image. 3) Tensile Data and Analysis This folder contains all of the raw tensile data for all tape-tape junction experiments conducted. All of the tensile data is in the folder titled, Raw Data Test Files. Within this folder is a .txt file for each sample tested. The file names are critical to the figure codes working properly because they contain the information for the junction angle and iterations. The file names are in the format year-month-day_trialnumber_junctionangle.txt. Also in the Raw Data Test Files folder are two functions used within some of the figure codes: fbfill and areacalculation. These functions will be used in the figure codes to properly analyze the data. To generate any figure using the MATLAB code in this folder, first open the code in MATLAB. Then within MATLAB, open the folder Raw Data Test Files. Only with this folder open in MATLAB will the code be able to find the correct raw data .txt files. The rest of the contents of this folder are MATLAB codes for specific figures in the manuscript. The only exception to this is the code titled, surfaceenergy_code, which is executed to calculate the phenomenological surface energy for the tapes used in these experiments.
more »
« less
Self-strengthening tape junctions inspired by recluse spider webs
Adhesive tapes are versatile and widely used yet lack adhesion strength due to their tendency to fail via peeling, a weak failure mode. A tape with surprising adhesive properties is the recluse spider's 50 nm-thin silk ribbon with a 1 : 150 aspect ratio. Junctions of these microscopic sticky tapes can withstand the material's tensile failure stress of ≈1 GPa. We modeled these natural tape–tape junctions and revealed a bi-modal failure behavior, critically dependent on the two tapes’ intersection angle. One mode leads to regular, low-strength peeling failure, while the other causes the junction to self-strengthen, eliminating the inherent weakness in peeling. This self-strengthening mechanism locks the two tapes together, increasing the junction strength by 550% and allowing some junctions to remain intact after tensile failure. This impressive adhesive strength of tapes has never before been observed or predicted. We found that recluse spiders make tape junctions with pre-stress to force the locked, high-strength failure mode. We used this approach to make junctions with synthetic adhesive tapes that overcame the weak peeling failure.
more »
« less
- NSF-PAR ID:
- 10383118
- Date Published:
- Journal Name:
- Materials Horizons
- Volume:
- 9
- Issue:
- 10
- ISSN:
- 2051-6347
- Page Range / eLocation ID:
- 2581 to 2591
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)This research presents an experimental program executed to understand the strength and stiffness properties of hollow built-up glass compression members that are intended for use in the modular construction of all glass, compression-dominant, shell-type structures. The proposed compression-dominant geometric form has been developed using the methods of form finding and three-dimensional graphical statics. This research takes the first steps towards a new construction methodology for glass structures where individual hollow glass units (HGU) are assembled using an interlocking system to form large, compression-dominant, shell-type structures, thereby exploiting the high compression strength of glass. In this study, an individual HGU has an elongated hexagonal prism shape and consists of two deck plates, two long side plates, and four short side plates, as is shown in Figure 1. Connections between glass plates are made using a two-sided transparent structural adhesive tape. The test matrix includes four HGUs, two each fabricated with 1 mm and 2 mm thick adhesive tape. All samples are dimensioned 64 cm on the long axis of symmetry, 51 cm on the short axis of symmetry, and are 10 cm in width. Glass plates are all 10 mm thick annealed float glass with geometric fabrication done using 5-axis abrasive water jet cutting. HGU assembly is accomplished using 3D printed truing clips and results in a rigid three-dimensional glass frame. Testing was done with the HGU oriented such that load was introduced on the short side edges of the two deck plates, resulting in an asymmetric load-support condition. A soft interface material was used between the HGU and steel plates of the hydraulic actuator and support for the purpose of avoiding premature cracking from local stress concentrations on the glass edges at the load and support locations. Force was applied in displacement control at 0.25 mm/minute with a full array of displacement and strain sensors. Test results for load vs. center deck plate transverse deflection are shown in Figure 2. All samples failed explosively by flexural buckling with no premature cracking on the load and support edges of the deck plates. Strain and deformation data clearly show the presence of second-order behavior resulting from bending deformation perpendicular to the plane of the deck plates. In general, linear axial behavior transitions to nonlinear second-order behavior, with increasing rates in deflection and strain growth, ultimately ending in glass fracture on the tension surfaces of the buckled deck plates. The failure resulted in near-complete disintegration of the deck plates, but with no observable cracking in any side plates and a secure connection on all adhesive tape. Results of the experimental program clearly demonstrate the feasibility of using HGUs for modular construction of compression dominant all-glass shell-type structures. This method of construction can significantly reduce the self-weight of the structure, and it will inspire the use of sustainable materials in the construction of efficient structures.more » « less
-
more » « less
Abstract Hierarchy in natural and synthetic materials has been shown to grant these architected materials properties unattainable independently by their constituent materials. While exceptional mechanical properties such as extreme resilience and high deformability have been realized in many human‐made three‐dimensional (3D) architected materials using beam‐and‐junction‐based architectures, stress concentrations and constraints induced by the junctions limit their mechanical performance. A new hierarchical architecture in which fibers are interwoven to construct effective beams is presented. In situ tension and compression experiments of additively manufactured woven and monolithic lattices with 30 µm unit cells demonstrate the superior ability of woven architectures to achieve high tensile and compressive strains (>50%)—without failure events—via smooth reconfiguration of woven microfibers in the effective beams and junctions. Cyclic compression experiments reveal that woven lattices accrue less damage compared to lattices with monolithic beams. Numerical studies of woven beams with varying geometric parameters present new design spaces to develop architected materials with tailored compliance that is unachievable by similarly configured monolithic‐beam architectures. Woven hierarchical design offers a pathway to make traditionally stiff and brittle materials more deformable and introduces a new building block for 3D architected materials with complex nonlinear mechanics.
-
more » « less
Abstract Biomaterials with outstanding mechanical properties, including spider silk, wood, and cartilage, often feature an oriented nanofibrillar structure. The orientation of nanofibrils gives rise to a significant mechanical anisotropy, which is extremely challenging to characterize, especially for microscopically small or inhomogeneous samples. Here, a technique utilizing atomic force microscope indentation at multiple points combined with finite element analysis to sample the mechanical anisotropy of a thin film in a microscopically small area is reported. The system studied here is the tape‐like silk of the Chilean recluse spider, which entirely consists of strictly oriented nanofibrils giving rise to a large mechanical anisotropy. The most detailed directional nanoscale structure–property characterization of spider silk to date is presented, revealing the tensile and transverse elastic moduli as 9 and 1 GPa, respectively, and the binding strength between silk nanofibrils as 159
± 13 MPa. Furthermore, based on this binding strength, the nanofibrils’ surface energy is derived as 37 mJ m−2, and concludes that van der Waals forces play a decisive role in interfibrillar binding. Due to its versatility, this technique has many potential applications, including early disease diagnostics, as underlying pathological conditions can alter the local mechanical properties of tissues. -
Heterogeneous bonding between metals and ceramics is of significant relevance to a wide range of applications in the fields of industry, defense, and aerospace. Metal/ceramic bonding can be used in various specific part applications such as vacuum tubes, automotive use of ceramic rotors, and rocket igniter bodies. However, the bonding of ceramic to metal has been challenging mainly due to (1) the low wettability of ceramics, on which the adhesion of molten adhesive bonders is limited and (2) the large difference between the coefficients of thermal expansion (CTE) of the two dissimilar bonded materials, which develops significant mechanical stresses at the interface and potentially leads to mechanical failures. Vapor-phase deposition is a widely used thin film processing technique in both academic research laboratories and manufacturing industries. Since vapor phase coatings do not require wettability or hydrophobicity, a uniform and strongly adherent layer is deposited over virtually any substrate, including ceramics. In this presentation, we report on the effect of vapor phase-deposited interfacial metal layers on the mechanical properties of bonding between stainless steel and Zerodur (lithium aluminosilicate-based glass ceramic). Direct-current magnetron sputtering was utilized to deposit various thin interfacial layers containing Ti, Cu, or Sn. In addition, to minimize the unfavorable stress at the bonded interface due to the large CTE difference, a low temperature allow solder, that can be chemically and mechanically activated at temperatures of approximately 200 °C, was used. The solder is made from a composite of Ti-Sn-Ce-In. A custom-built fixture and universal testing machine were used to evaluate the bonding strength in shear, which was monitored in-situ with LabView throughout the measurement. The shear strength of the bonding between stainless steel and Zerodur was systematically characterized as a function of interfacial metal and metal processing temperature during sputter depositions. Maximum shear strength of the bonding of 4.36 MPa was obtained with Cu interfacial layers, compared to 3.53 MPa from Sn and 3.42 MPa from Ti adhesion promoting layers. These bonding strengths are significantly higher than those (~0.05 MPa) of contacts without interfacial reactive thin metals. The fracture surface microstructures are presented as well. It was found that the point of failure, when Cu interfacial layers were used, was between the coated Cu film and alloy bonder. This varied from the Sn and Ti interfacial layers where the main point of failure was between the interfacial film and Zerodur interface. The findings of the effect of thin adhesion promoting metal layers and failure behaviors may be of importance to some metal/ceramic heterogeneous bonding studies that require high bonding strength and low residual stresses at the bonding interface. The authors gratefully acknowledge the financial support of the Improvement of Measurement Standards and Technology for Mechanical Metrology (Grant No. 20011028) by KRISS.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/D2MH00403H
