Differential carrier lifetime measurements were performed on c-plane InGaN/GaN single quantum well (QW) light-emitting diodes (LEDs) of different QW indium compositions as well as with and without doped barriers. Mg-doped p-type and Si-doped n-type barriers close to the QW were used to reduce the net internal electric field in the QW, thereby improving the electron–hole wavefunction overlap on the LEDs. LEDs with doped barriers show short lifetimes and low carrier densities in the active region compared to the reference LEDs. The recombination coefficients in the ABC model were estimated based on the carrier lifetime and quantum efficiency measurements. The improvement in the radiative coefficients in the LEDs with doped barriers coupled with the blueshift of the emission wavelengths indeed indicates an enhancement in wavefunction overlap and a reduction of quantum confined Stark effect as a result of the reduced internal electric field. However, doped barriers also introduce non-radiative recombination centers and thereby increase the Shockley–Read–Hall (SRH) coefficient, although the increment is less for LEDs with high indium composition QWs. As a result, at high indium composition (22%), LEDs with doped barriers outperform the reference LEDs even though the trend is reversed for LEDs with lower indium composition (13.5%). Despite the trade-off of higher SRH coefficients, doped barriers are shown to be effective in reducing the internal electric field and increasing the recombination coefficients.
- Award ID(s):
- 1839077
- PAR ID:
- 10395744
- Editor(s):
- Morkoç, Hadis; Fujioka, Hiroshi; Schwarz, Ulrich T.
- Date Published:
- Journal Name:
- SPIE OPTO
- Page Range / eLocation ID:
- 17
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
Abstract This report classifies emission inhomogeneities that manifest in InGaN quantum well blue light-emitting diodes grown by plasma-assisted molecular beam epitaxy on free-standing GaN substrates. By a combination of spatially resolved electroluminescence and cathodoluminescence measurements, atomic force microscopy, scanning electron microscopy and hot wet potassium hydroxide etching, the identified inhomogeneities are found to fall in four categories. Labeled here as type I through IV, they are distinguishable by their size, density, energy, intensity, radiative and electronic characteristics and chemical etch pits which correlates them with dislocations. Type I exhibits a blueshift of about 120 meV for the InGaN quantum well emission attributed to a perturbation of the active region, which is related to indium droplets that form on the surface in the metal-rich InGaN growth condition. Specifically, we attribute the blueshift to a decreased growth rate of and indium incorporation in the InGaN quantum wells underneath the droplet which is postulated to be the result of reduced incorporated N species due to increased N 2 formation. The location of droplets are correlated with mixed type dislocations for type I defects. Types II through IV are due to screw dislocations, edge dislocations, and dislocation bunching, respectively, and form dark spots due to leakage current and nonradiative recombination.more » « less
-
more » « less
InGaN templates have recently attracted interest due to their ability to reduce strain in the quantum wells and to induce a red shift in the emission wavelength. For such technology to be competitive, it should outperform the traditional technology for LEDs grown on GaN substrates and offer improved output characteristics. InGaN based LEDs on InyGa1−yN templates with varying In-content of 8% ≤ y ≤ 12% are studied for the same emission wavelength. The electroluminescence, optical output power, and external quantum efficiency of the LEDs are investigated as a function of the In-content in the templates. LEDs on InGaN templates with In-content of 8–10% show better performance than LEDs grown on GaN. This enhancement is attributed to improved radiative recombination as a result of the reduced strain in the quantum wells. However, templates with In-content of ∼10.5% and ∼11% show inferior performance to the LEDs on GaN because the deterioration from the increased defects from the template is stronger than the improvement in the radiative recombination. It can be concluded that the InGaN templates with 8–10% offer a technology for LEDs that is outperforming the traditional GaN technology.
-
null (Ed.)AlGaN-delta-GaN quantum well (QW) structures have been demonstrated to be good candidates for the realization of high-efficiency deep-ultraviolet (DUV) light-emitting diodes (LEDs). However, such heterostructures are still not fully understood. This study focuses on investigation of the optical properties and efficiency of the AlGaN-delta-GaN QW structures using self-consistent six-band k⸱p modelling and finite difference time domain (FDTD) simulations. Structures with different Al contents in the AlxGa1−xN sub-QW and AlyGa1−yN barrier regions are examined in detail. Results show that the emission wavelength (λ) can be engineered through manipulation of delta-GaN layer thickness, sub-QW Al content (x), and barrier Al content (y), while maintaining a large spontaneous emission rate corresponding to around 90% radiative recombination efficiency (ηRAD). In addition, due to the dominant transverse-electric (TE)-polarized emission from the AlGaN-delta-GaN QW structure, the light extraction efficiency (ηEXT) is greatly enhanced when compared to a conventional AlGaN QW. Combined with the large ηRAD, this leads to the significant enhancement of external quantum efficiency (ηEQE), indicating that AlGaN-delta-GaN structures could be a promising solution for high-efficiency DUV LEDs.more » « less
-
more » « less
Scanning tunneling electroluminescence (STL) microscopy is performed on a 3 nm‐thick InGaN/GaN quantum well (QW) with [In] = 0.23 such that the main light emission occurs in the green. The technique is used to map the radiative recombination properties at a scale of a few nanometers and correlate the local electroluminescence map with the surface topography simultaneously imaged by scanning tunneling microscopy. While the expected green emission is observed all over the sample, measurements performed on a 500 nm × 500 nm area around a 150 nm‐large and 2.5 nm‐deep hexagonal defect reveal intense emission peaks at higher energies close to the defect edges, features which are not visible in the macrophotoluminescence spectrum of the sample. Via a fitting of the local tunneling electroluminescence spectra, quantitative information on the fluctuations of the intensity, peak energy, width, and phonon replica intensity of the different spectral contributions is obtained, which provides information on carrier localization in the QW. This procedure also indicates that the carrier diffusion length on the probed area of the QW is shorter than 50 nm.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1117/12.2608695
