An official website of the United States government
This work reports a method of producing flexible cobalt nanowires (NWs) directly from the chemical conversion of bulk precursors at room temperature. Chemical reduction of Li 6 CoCl 8 produces a nanocomposite of Co and LiCl, of which the salt is subsequently removed. The dilute concentration of Co in the precursor combined with the anisotropic crystal structure of the hcp phase leads to 1D growth in the absence of any templates or additives. The Co NWs are shown to have high saturation magnetization (130.6 emu g −1 ). Our understanding of the NW formation mechanism points to new directions of scalable nanostructure generation.
more »
« less
Magnetic structure and internal field nuclear magnetic resonance of cobalt nanowires
The magnetic properties of cobalt metal nanowires grown by electrodeposition in porous membranes depend largely on the synthesis conditions. Here, we focus on the role of electrolyte additives on the magnetic anisotropy of the electrodeposited nanowires. Through magnetometry and internal field nuclear magnetic resonance (IF NMR) studies, we compared both the magnetic and crystalline structures of 50 and 200 nm diameter Co nanowires synthesized in the presence or absence of organic additives. The spectral characteristics of IF NMR were compared structurally to X-ray diffraction patterns, and the anisotropy of the NMR enhancement factor in ferromagnetic multidomain structures to magnetometry results. While the magnetic behavior of the 50 nm nanowires was dominated, as expected, by shape anisotropy with magnetic domains oriented on axis, the analysis of the 200 nm proved to be more complex. 59 Co IF NMR revealed that the determining difference between the samples electrodeposited in the presence or in absence of organic additives was not the dominant crystalline system (fcc or hcp) but the coherent domain sizes and boundaries. In the presence of organic additives, the cobalt crystal domains are smaller and with defective grain boundaries, as revealed by resonances below 210 MHz. This prevented the development in the Co hcp part of the sample of the strong magnetocrystalline anisotropy that was observed in the absence of organic additives. In the presence of organic additives, even in nanowires as wide as 200 nm, the magnetic behavior remained determined by the shape anisotropy with a positive effective magnetic anisotropy and strong anisotropy of the NMR enhancement factor.
more »
« less
- PAR ID:
- 10398328
- Date Published:
- Journal Name:
- Physical Chemistry Chemical Physics
- Volume:
- 24
- Issue:
- 19
- ISSN:
- 1463-9076
- Page Range / eLocation ID:
- 11898 to 11909
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Three mononuclear tetrakis(pseudohalido)-cobalt( ii ) complexes (Ph 4 P) 2 [Co(E) 4 ] (E = N 3 − , 1; NCO − , 2; NCS − , 3) have been synthesized and structurally characterized. Each compound contains a distorted tetrahedral Co 2+ ion coordinated by four pseudohalide ligands. The magnetic properties of 1–3 have been studied using direct-current magnetic measurements and high-frequency and -field EPR spectroscopy (HFEPR), suggesting easy-axis magnetic anisotropy for 1 and 2 and easy-plane anisotropy for 3. Analysis of the HFEPR spectra yielded D values of −5.23 and +3.63 cm −1 for 2 and 3, respectively. The absence of the EPR signal in 1 is consistent with a large, negative value of the zero-field splitting (ZFS) parameter D in 1. The nature of magnetic anisotropies of 1–3 has also been confirmed by ab initio calculations. The calculated D values are consistent with those determined using magnetometry and HFEPR studies. Alternating current (AC) magnetic susceptibilities reveal slow magnetic relaxation under an applied magnetic field, thus indicating that 1–3 are field-induced single-ion magnets (SIMs).more » « less
-
Anisotropy constants of magnetic materials are typically determined through angle-resolved Ferromagnetic Resonance (ar-FMR) and torque magnetometry, which can be time consuming measurements, thus limiting their utility. The Stoner–Wohlfarth model can be used to numerically fit measured magnetic hysteresis curves to more easily determine these anisotropy constants. To demonstrate this, 10 nm bct FexCoyMnz single-crystal films grown by molecular beam epitaxy on MgO(001) substrates were investigated. The hysteresis behavior measured by vibrating sample magnetometry was least-squares fit against numerically calculated hysteresis curves generated from the Stoner–Wohlfarth model to extract the anisotropy constants. The cubic anisotropy of different compositions of FeCoMn films was at ∼104 J/m3, which is on the same order of magnitude of bct Fe and Co thin films measured by ar-FMR and torque magnetometry techniques.more » « less
-
ReMo binary alloy films with a maximum Mo content of 25 at. % are successfully electrodeposited using high concentration acetate solutions in the presence of citric acid. The electrochemical behavior of the ReMo alloy is studied using cyclic voltammetry and anodic stripping methods. Different techniques, including electron microscopy, x-ray diffraction, and four-point probe resistance measurements at cryogenic temperature, are used to characterize the surface morphology, crystal structure, and superconducting critical temperature of alloys, respectively. While all films exhibit a crystalline hcp phase after 700 °C annealing, the film with the highest 25 at. % Mo content shows a second crystalline cubic phase. Mo doping preserves the enhanced superconducting transition temperature (Tc) in electrodeposited amorphous Re films and improves the stability of Tc against thermal annealing at a temperature of 200 °C. This is the first successful demonstration to use a dopant to stabilize the enhanced Tc of electrodeposited films, enabling the fabrication and operation of superconducting connectors above the intrinsic Tc of the materials.more » « less
-
Bonded magnetic composites combine the cost-effectiveness, low density, and manufacturing flexibility of conventional polymer binders with the unique magnetic characteristics of magnetic powders/fillers to form multifunctional magneto polymeric composites that offer superior properties to conventional sintered magnets. In this study, a co-rotating twin screw extruder was used to fabricate 20 and 40 wt.% strontium ferrite/polyamide 4.6 bonded magnetic composites viable for fused filament fabrication 3D printing. The characterization conducted on the bonded magnetic composites was scanning electron microscopy, simultaneous differential thermogravimetry, and vibrating sample magnetometry. The microstructure of the bonded composite exhibited a uniform platelet morphology of the strontium ferrite magnetic particles. There was no observable depreciation in the melting transitions, which suggests a thermally resistant magnetic composite. An appreciable increment in % crystallinity of 13 and 20% for 20wt. % and 40wt. % strontium ferrites bonded magnets were observed. This is attributable to the heterogeneous nucleation phenomenon, where the metal powders act as nucleation sites for increased crystalline domains. The bonded composite exhibited significant magnetic anisotropy, with the remanence (Mr), which is the most important property for magnetic application significantly increasing to 49.8% along the easy direction in comparison to the hard axis. This suggests the viability of the fabricated bonded composites in viable in producing anisotropic bonded magnetic devices, which are considered to exhibit stronger magnetic properties.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/d1cp05164d
