An official website of the United States government
A multiscale simulation approach is developed to simulate the contact transport properties between semimetal and a monolayer two-dimensional transition metal dichalcogenide (TMDC) semiconductor. The results elucidate the mechanisms for low contact resistance between semimetal and TMDC semiconductor contacts from a quantum transport perspective. The simulation results compare favorably with recent experiments. Furthermore, the results show that the contact resistance of a bismuth-MoS2contact can be further reduced by engineering the dielectric environment and doping the TMDC material to [Formula: see text]. The quantum transport simulation indicates the possibility to achieve an ultrashort contact transfer length of ∼1 nm, which can allow aggressive scaling of the contact size.
more »
« less
Semimetal–Monolayer Transition Metal Dichalcogenides Photodetectors for Wafer‐Scale Broadband Photonics
Atomically thin 2D transition metal dichalcogenides (TMDs), such as MoS2, are promising candidates for nanoscale photonics because of strong light–matter interactions. However, Fermi‐level pinning due to metal‐induced gap states (MIGS) at the metal–monolayer (1L)‐MoS2interface limits the application of optoelectronic devices based on conventional metals due to high contact resistance. On the other hand, a semimetal–TMD–semimetal device can overcome this limitation, where the MIGS are sufficiently suppressed allowing ohmic contacts. Herein, the optoelectronic performance of a bismuth–1L‐MoS2–bismuth device with ohmic electrical contacts and extraordinary optoelectronic properties is demonstrated. To address the wafer‐scale production, full coverage 1L‐MoS2grown by chemical vapor deposition. High photoresponsivity of 300 A W−1at wavelength 400 nm measured at 77 K, which translates into an external quantum efficiency (EQE) ≈1000 or 105%, is measured. The 90% rise time of the devices at 77 K is 0.1 ms, suggesting they can operate at the speed of ≈10 kHz. High‐performance broadband photodetector with spectral coverage ranging from 380 to 1000 nm is demonstrated. The combination of large‐array device fabrication, high sensitivity, and high‐speed response offers great potential for applications in photonics, including integrated optoelectronic circuits.
more »
« less
- Award ID(s):
- 2151971
- PAR ID:
- 10400098
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Photonics Research
- Volume:
- 4
- Issue:
- 4
- ISSN:
- 2699-9293
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract 2D layered semiconductors have attracted considerable attention for beyond‐Si complementary metal‐oxide‐semiconductor (CMOS) technologies. They can be prepared into ultrathin channel materials toward ultrascaled device architectures, including double‐gate field‐effect‐transistors (DGFETs). This work presents an experimental analysis of DGFETs constructed from chemical vapor deposition (CVD)‐grown monolayer (1L) molybdenum disulfide (MoS2) with atomic layer deposition (ALD) of hafnium oxide (HfO2) high‐k gate dielectrics (top and bottom). This extends beyond previous studies of DGFETs based mostly on exfoliated (few‐nm thick) MoS2flakes, and advances toward large‐area wafer‐scale processing. Here, significant improvements in performance are obtained with DGFETs (i.e., improvements in ON/OFF ratio, ON‐state current, sub‐threshold swing, etc.) compared to single top‐gate FETs. In addition to multi‐gate device architectures (e.g., DGFETs), the scaling of the equivalent oxide thickness (EOT) is crucial toward improved electrostatics required for next‐generation transistors. However, the impact of EOT scaling on the characteristics of CVD‐grown MoS2DGFETs remains largely unexplored. Thus, this work studies the impact of EOT scaling on subthreshold swing (SS) and gate hysteresis using current–voltage (I–V) measurements with varying sweep rates. The experimental analysis and results elucidate the basic mechanisms responsible for improvements in CVD‐grown 1L‐MoS2DGFETs compared to standard top‐gate FETs.more » « less
-
Abstract Printed 2D materials, derived from solution‐processed inks, offer scalable and cost‐effective routes to mechanically flexible optoelectronics. With micrometer‐scale control and broad processing latitude, aerosol‐jet printing (AJP) is of particular interest for all‐printed circuits and systems. Here, AJP is utilized to achieve ultrahigh‐responsivity photodetectors consisting of well‐aligned, percolating networks of semiconducting MoS2nanosheets and graphene electrodes on flexible polyimide substrates. Ultrathin (≈1.2 nm thick) and high‐aspect‐ratio (≈1 μm lateral size) MoS2nanosheets are obtained by electrochemical intercalation followed by megasonic atomization during AJP, which not only aerosolizes the inks but also further exfoliates the nanosheets. The incorporation of the high‐boiling‐point solvent terpineol into the MoS2ink is critical for achieving a highly aligned and flat thin‐film morphology following AJP as confirmed by grazing‐incidence wide‐angle X‐ray scattering and atomic force microscopy. Following AJP, curing is achieved with photonic annealing, which yields quasi‐ohmic contacts and photoactive channels with responsivities exceeding 103 A W−1that outperform previously reported all‐printed visible‐light photodetectors by over three orders of magnitude. Megasonic exfoliation coupled with properly designed AJP ink formulations enables the superlative optoelectronic properties of ultrathin MoS2nanosheets to be preserved and exploited for the scalable additive manufacturing of mechanically flexible optoelectronics.more » « less
-
Abstract The performance of electronic and optoelectronic devices is dominated by charge carrier injection through the metal–semiconductor contacts. Therefore, creating low-resistance electrical contacts is one of the most critical challenges in the development of devices based on new materials, particularly in the case of two-dimensional semiconductors. Herein, we report a strategy to reduce the contact resistance of MoS 2 via local pressurization. We fabricated electrical contacts using an atomic force microscopy tip and applied variable pressure ranging from 0 to 25 GPa. By measuring the transverse electronic transport properties, we show that MoS 2 undergoes a reversible semiconducting-metallic transition under pressure. Planar devices in field effect configuration with electrical contacts performed at pressures above ∼15 GPa show up to 30-fold reduced contact resistance and up to 25-fold improved field-effect mobility when compared to those measured at low pressure. Theoretical simulations show that this enhanced performance is due to improved charge injection to the MoS 2 semiconductor channel through the metallic MoS 2 phase obtained by pressurization. Our results suggest a novel strategy for realizing improved contacts to MoS 2 devices by local pressurization and for exploring emergent phenomena under mechano-electric modulation.more » « less
-
Abstract The use of metal and semimetal van der Waals contacts for 2D semiconducting devices has led to remarkable device optimizations. In comparison with conventional thin-film metal deposition, a reduction in Fermi level pinning at the contact interface for van der Waals contacts results in, generally, lower contact resistances and higher mobilities. Van der Waals contacts also lead to Schottky barriers that follow the Schottky–Mott rule, allowing barrier estimates on material properties alone. In this study, we present a double Schottky barrier model and apply it to a barrier tunable all van der Waals transistor. In a molybdenum disulfide (MoS2) transistor with graphene and few-layer graphene contacts, we find that the model can be applied to extract Schottky barrier heights that agree with the Schottky–Mott rule from simple two-terminal current–voltage measurements at room temperature. Furthermore, we show tunability of the Schottky barrierin-situusing a regional contact gate. Our results highlight the utility of a basic back-to-back diode model in extracting device characteristics in all van der Waals transistors.more » « less
