More Like this

1. Light angle dependence of photothermal properties in oxide and porphyrin thin films for energy-efficient window applications

   https://doi.org/https://doi.org/10.1557/mrc.2020.39  

   1. Lyu M, Lin J (June 2020, MRS communications)

   null (Ed.)

   The photothermal experiments on the incident light angle dependence are carried out using simulated solar light on thin films of both iron oxides (Fe3O4 and Fe3O4@Cu2-xS) and porphyrin compounds (chlorophyll and chlorophyllin). Fe3O4 and Fe3O4@Cu2-xS are synthesized using various solution methods that produce mono-dispersed nanoparticles on the order of 10 nm. Chlorophyll is extracted from fresh spinach and chlorophyllin sodium copper is a commercial product. These photothermal (PT) materials are dispersed in polymethyl methacrylate (PMMA) solutions and deposited on glass substrates via spin coating that result in clear and transparent thin films. The iron-oxide based thin films show distinctive absorption spectra; Fe3O4 exhibits a strong peak near UV and gradually decreases into the visible and NIR regions; the absorption of Fe3O4@Cu2-xS is similar in the UV region but shows a broad absorption in the NIR region. Both chlorophyll and chlorophyllin are characterized with absorption peaks near UV and NIR showing a “U”-shaped spectrum, ideally required for efficient solar harvest and high transparency in energy-efficient single-pane window applications. Upon coating of the transparent PT films on the window inner surfaces, solar irradiation induces the photothermal effect, consequently raising the film temperature. In this fashion, the thermal loss through the window can be significantly lowered by reducing the temperature difference between the window inner surface and the room interior, based on a new concept of so-called “optical thermal insulation” (OTI) without any intervention medium, such as air/argon, as required in the glazing technologies. Single-panes are therefore possible to replace double- or triple panes. As OTI is inevitably affected by seasonal and daily sunlight changes, an incident light angle dependence of the photothermal effect is crucial in both thin film and window designs. It is found that the heating curves reach their maxima at small angles of incidence while the photothermal effect is considerably reduced at large angles. This angle dependence is well explained by light reflection by the thin film surface, however, deviated from what is predicted by the Fresnel’s law, attributable to non-ideal surfaces of the substrates. The angle dependence data provides an important reference for OTI that window exposure to sun is greater at winter solstice while that is considerably reduced in the summer. This conclusion indicates much enhanced solar harvesting and heat conversion via optically insulated windows in the winter season, resulting in much lower U-factors. 

   more » « less
2. Fluorescent Waveguide Lattices for Enhanced Light Harvesting and Solar Cell Performance

   https://doi.org/10.1021/acsaem.3c00687  

   Ding, Nannan; Hosein, Ian D (June 2023, ACS Applied Energy Materials)

   We present the properties and performance of fluorescent waveguide lattices as coatings for solar cells, designed to address the significant mismatch between the solar cell’s spectral response range and the solar spectrum. Using arrays of microscale visible light optical beams transmitted through photoreactive polymer resins comprising acrylate and silicone monomers and fluorescein o,o′-dimethacrylate comonomer, we photopolymerize well-structured films with single and multiple waveguide lattices. The materials exhibited bright green-yellow fluorescence emission through down-conversion of blue-UV excitation and light redirection from the dye emission and waveguide lattice structure. This enables the films to collect a broader spectrum of light, spanning UV–vis–NIR over an exceptionally wide angular range of ±70°. When employed as encapsulant coatings on commercial silicon solar cells, the polymer waveguide lattices exhibited significant enhancements in solar cell current density. Below 400 nm, the primary mode of enhancement is through down-conversion and light redirection from the dye emission and collection by the waveguides. Above 400 nm, the primary modes of enhancement were a combination of down-conversion, wide-angle light collection, and light redirection from the dye emission and collection by the waveguides. Waveguide lattices with higher dye concentrations produced more well-defined structures better suited for current generation in encapsulated solar cells. Under standard AM 1.5 G irradiation, we observed nominal average current density increases of 0.7 and 1.87 mA/cm2 for single waveguide lattices and two intersecting lattices, respectively, across the full ±70° range and reveal optimal dye concentrations and suitable lattice structures for solar cell performance. Our findings demonstrate the significant potential of incorporating down-converting fluorescent dyes in polymer waveguide lattices for improving the current spectral and angular response of solar cell technologies toward increasing clean energy in the energy grid. 

   more » « less
3. Optical design of perovskite solar cells for applications in monolithic tandem configuration with CuInSe2 bottom cells

   https://doi.org/10.1557/adv.2018.464  

   Ahangharnejhad, Ramez H.; Song, Zhaoning; Phillips, Adam B.; Watthage, Suneth C.; Almutawah, Zahrah S.; Sapkota, Dhurba R; Koirala, Prakash; Collins, Robert W.; Yan, Yanfa; Heben, Michael J. (January 2018, MRS Advances)

   Abstract: Monolithic integrated thin film tandem solar cells consisting of a high bandgap perovskite top cell and a low bandgap thin film bottom cell are expected to reach higher power conversion efficiencies (PCEs) with lower manufacturing cost and environmental impacts than the market-dominant crystalline silicon photovoltaics. There have been several demonstrations of 4-terminal and 2-terminal perovskite tandem devices with CuInGaSe 2 (CIGS) or CuInSe 2 (CIS) and, similar to the other tandem structures, the optimization of this device relies on optimal choice for the perovskite bandgap and thickness. Therefore, further advancement will be enabled by tuning the perovskite absorber to maximize the photocurrent limited by the current match condition. Here, we systematically study the optical absorption and transmission of perovskite thin films with varying absorber band gap. Based on these results, we model the photocurrent generations in both perovskite and CIS subcells and estimate the performances of projected tandem devices by considering the ideally functioning perovskite and CIS device. Our results show that for perovskite layers with 500 nm thickness the optimal bandgap is around 1.6 eV. With these configurations, PCEs above 20% could be achieved by monolithically integrated perovskite/CIS tandem solar cells. Also by modelling the absorption at every layer we calculate the quantum efficiency at each subcell in addition to tracking optical losses. 

   more » « less
4. Improving the Passivation of Molybdenum Oxide Hole‐Selective Contacts with 1 nm Hydrogenated Aluminum Oxide Films for Silicon Solar Cells

   https://doi.org/10.1002/pssa.202000093  

   Gregory, Geoffrey; Feit, Corbin; Gao, Zhengning; Banerjee, Parag; Jurca, Titel; Davis, Kristopher O. (May 2020, physica status solidi (a))

   The intrinsic and doped amorphous silicon layers in silicon heterojunction solar cells parasitically absorb light in the short wavelength region of the solar spectrum, lowering the generation current available to the device. Herein, a promising alternative to the hole‐selective amorphous silicon contact layers using only wide bandgap, transparent oxide materials is presented. Using thermal atomic layer deposition, a 1 nm hydrogenated aluminum oxide layer is deposited followed by a 4 nm molybdenum oxide layer on n‐type crystalline silicon. This contact stack provides an effective carrier lifetime of 1.14 ms. It is shown that the molybdenum oxide layer is successfully deposited with a high work function, which facilitates efficient hole extraction and repels majority carriers from the c‐Si surface. Then the implied open‐circuit voltage, saturation current density, and contact resistivity are recorded as a function of contact annealing temperature and show that they are relatively stable up to 200 °C. 

   more » « less
5. Near full light absorption and full charge collection in 1-micron thick quantum dot photodetector using intercalated graphene monolayer electrodes

   https://doi.org/10.1039/c9nr09901h  

   Chen, Wenjun; Ahn, Seungbae; Balingit, Marquez; Wang, Jiaying; Lockett, Malcolm; Vazquez-Mena, Oscar (February 2020, Nanoscale)

   Quantum dots (QDs) offer several advantages in optoelectronics such as easy solution processing, strong light absorption and size tunable direct bandgap. However, their major limitation is their poor film mobility and short diffusion length (<250 nm). This has restricted the thickness of QD film to ∼200–300 nm due to the restriction that the diffusion length imposes on film thickness in order to keep efficient charge collection. Such thin films result in a significant decrease in quantum efficiency for λ > 700 nm in QDs photodetector and photovoltaic devices, causing a reduced photoresponsivity and a poor absorption towards the near-infrared part of the sunlight spectrum. Herein, we demonstrate 1 μm thick QDs photodetectors with intercalated graphene charge collectors that avoid the significant drop of quantum efficiency towards λ > 700 nm observed in most QD optoelectronic devices. The 1 μm thick intercalated QD films ensure strong light absorption while keeping efficient charge extraction with a quantum efficiency of 90%–70% from λ = 600 nm to 950 nm using intercalated graphene layers as charge collectors with interspacing distance of 100 nm. We demonstrate that the effect of graphene on light absorption is minimal. We achieve a time-modulation response of <1 s. We demonstrate that this technology can be implemented on flexible PET substrates, showing 70% of the original performance after 1000 times bending test. This system provides a novel approach towards high-performance photodetection and high conversion photovoltaic efficiency with quantum dots and on flexible substrates. 

   more » « less