An official website of the United States government
This paper reports an integrated dual-modality microfluidic sensor chip, consisting of a patterned periodic array of nanoposts coated with gold (Au) and graphene oxide (GO), to detect target biomarker molecules in a limited sample volume. The device generates both electrochemical and surface plasmon resonance (SPR) signals from a single sensing area of Au–GO nanoposts. The Au–GO nanoposts are functionalized with specific receptor molecules, serving as a spatially well-defined nanostructured working electrode for electrochemical sensing, as well as a nanostructured plasmonic crystal for SPR-based sensing via the excitation of surface plasmon polaritons. High sensitivity of the electrochemical measurement originates from the presence of the nanoposts on the surface of the working electrode where radial diffusion of redox species occurs. Complementarily, the SPR detection allows convenient tracking of dynamic antigen–antibody interactions, to describe the association and dissociation phases occurring at the sensor surface. The soft-lithographically formed nanoposts provide high reproducibility of the sensor response to epidermal growth factor receptor ( ErbB2 ) molecules even at a femtomolar level. Sensitivities of the electrochemical measurements to ErbB2 are found to be 20.47 μA μM −1 cm −2 in a range from 1 fM to 0.1 μM, and those of the SPR measurements to be 1.35 nm μM −1 in a range from 10 pM to 1 nM, and 0.80 nm μM −1 in a range from 1 nM to 0.1 μM. The integrated dual-modality sensor offers higher sensitivity (through higher surface area and diffusions from nanoposts for electrochemical measurements), as well as the dynamic measurements of antigen–antibody bindings (through the SPR measurement), while operating simultaneously in a same sensing area using the same sample volume.
more »
« less
Voltammetry Peak Tracking for Longer-Lasting and Reference-Electrode-Free Electrochemical Biosensors
Electrochemical aptamer-based sensors offer reagent-free and continuous analyte measurement but often suffer from poor longevity and potential drift even with a robust 3-electrode system. Presented here is a simple, software-enabled approach that tracks the redox-reporter peak in an electrochemical aptamer-based sensor and uses the measurement of redox peak potential to reduce the scanning window to a partial measure of redox-peak-height vs. baseline (~10X reduction in voltage range). This same measurement further creates a virtual reference standard in buffered biofluids such as blood and interstitial fluid, thereby eliminating the effects of potential drift and the need for a reference electrode. The software intelligently tracks voltammogram peak potential via the inflection points of the rising and falling slopes of the measured redox peak. Peak-tracking-derived partial scanning was validated over several days and minimized electrochemically induced signal loss to <5%. Furthermore, the peak-tracking approach was shown to be robust against confounding effects such as fouling. From an applied perspective in creating wearable biosensors, the peak-tracking approach further enables use of a single implanted working electrode, while the counter/reference-electrode may utilize a simple gel-pad electrode on the surface of the skin, compared to implanting working, counter, and reference electrodes conventionally used for stability and reliability but is also costly and invasive. Cumulatively, peak-tracking provides multiple leaps forward required for practical molecular monitoring by extending sensor longevity, eliminating potential drift, simplifying biosensor device construction, and in vivo placement for any redox-mediated sensor that forms parabolic-like data.
more »
« less
- PAR ID:
- 10412264
- Date Published:
- Journal Name:
- Biosensors
- Volume:
- 12
- Issue:
- 10
- ISSN:
- 2079-6374
- Page Range / eLocation ID:
- 782
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
We report a Tuning Fork Scanning Electrochemical Cell Microscopy (TF-SECCM) technique for providing morphological and electrochemical information of single redox-active entities. This new operation configuration of SECCM utilizes an electrolyte-filled nanopipette tip mounted onto a tuning fork force sensor to obtain a precise tip-sample distance control and surface morphological mapping. Redox activities of regions of interest can be investigated by scanning electrode potential by moving the nanopipette to any target regions while maintaining the constant force engagement of the tip with the sample. Using silver nanowires (Ag NWs) as a model system due to their extensive utilization in energy and sensing devices, TF-SECCM provides not only the topography of single Ag NWs but also their distinctive redox activities and catalytic hydrogen evolution reaction (HER) activities and electrolyte anion adsorption/desorption features in contrast to NW bundles and supporting substrate (e.g., indium tin oxide).more » « less
-
The desire to translate biosensors for real time molecular monitoring has intensified due to the commercial success of 2-week continuous glucose monitors. However, a common limitation for emerging biosensors is that their lifetimes are often too short for commercially expected benchmarks of at least 3-day and ideally 2-week operation. Electrochemical sensors remain the preferred format of biochemical sensing thanks to their low cost, size, weight, and power requirements for mobile deployment. When exposed to biological fluid, all electrochemical sensors require a blocking layer to protect the electrode surface from fouling and redox interferents. Traditional blocking layer approaches rely on self-assembled monolayers which are often fragile to biological interferents like proteins and require specific electrode materials to improve their stability. Presented here is an evaluation of ultra-thin inorganic oxide and nitride films as an alternative to self-assembled monolayer blocking layers. Specifically, silicon oxide, silicon nitride, and aluminum oxide films were deposited by electron beam evaporation or atomic layer deposition at thicknesses of several nanometers to mimic the electrical capacitance of a conventional monolayer blocking layer. These oxide films were characterized over 7-days and demonstrated to provide poor protection against interfering redox currents from dissolved ferricyanide (150 - 300 µA/cm2) and oxygen reduction interference (30 - 60 µA/cm2). The oxide films were then used as a blocking layer in an electrochemical aptamer sensor using the previously published aptamer for phenylalanine. The phenylalanine sensor showed a binding affinity stronger than found in literature, but a reduced signal gain (∼ 20 % change in methylene blue redox current compared to the expected 50 % previously published on gold). It is speculated and supported by literature that these oxide and nitride films gradually dissolve over periods of days in an aqueous environment. Results further show that if lower quality oxide or nitride films are used, they may be more stable, but at the cost of initially higher in currents. While oxide and nitride films fail to improve upon the performance of thiol-blocking layers on gold electrodes, they may provide utility in some applications by allowing for alternate electrode materials and surfaces to be used instead of traditional self-assembled monolayers on gold electrodes.more » « less
-
Abstract Liquid aerosols are ubiquitous in nature, and several tools exist to quantify their physicochemical properties. As a measurement science technique, electrochemistry has not played a large role in aerosol analysis because electrochemistry in air is rather difficult. Here, a remarkably simple method is demonstrated to capture and electroanalyze single liquid aerosol particles with radii on the order of single micrometers. An electrochemical cell is constructed by a microwire (cylindrical working electrode) traversing a film of ionic liquid (1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl)imide) that is suspended within a wire loop (reference/counter electrode). An ionic liquid is chosen because the low vapor pressure preserves the film over weeks, vastly improving suspended film electroanalysis. The resultant high surface area allows the suspended ionic liquid cell to act as an aerosol net. Given the hydrophobic nature of the ionic liquid, aqueous aerosol particles do not coalesce into the film. When the liquid aerosols collide with the sufficiently biased microwire (creating a complex boundary: aerosol|wire|ionic liquid|air), the electrochemistry within a single liquid aerosol particle can be interrogated in real‐time. The ability to achieve liquid aerosol size distributions for aerosols over 1 µm in radius is demonstrated.more » « less
-
Ion selective electrode (ISE) sensors have been broadly applied for real-time in situ monitoring of ion concentrations in water environments. However, ISE sensors suffer from critical problems, such as ionophore leaching, water-penetration, poor electrochemical stability, and resulting short life spans. In this study, a template-guided membrane matrix immobilization strategy was pursued as a novel ISE sensor fabrication methodology to enhance its sensing characteristics and longevity. Specifically, nano-porous anodized aluminum oxide (AAO) was used as the template for an NH 4 + -specific ISE sensor. A nano-porous nickel mesh eventually replaced the template and formed a compact, high-surface juncture with the NH 4 + ion-selective membrane matrix. The resulting template-guided nano-mesh ISE (TN-ISE) sensor displayed enhanced electrochemical stability ( i.e. , capacitance increased by 50%, reading drift reduced by 75%) when compared to a regular single-wall carbon nanotube (SW-CNT) ISE sensor used as the standard. The interface between the nano-mesh electrode and the ion selective membrane matrix was compact enough to prevent water influx at the electrode interface. This minimized ionophore leaching and increased the mechanical integrity of the TN-ISE sensor. The practical advantages of the novel sensor were validated via long-term (360 hours) tests in real wastewater, returning a small average error of 1.28% over this time. The results demonstrate the feasibility of the template-guided nano-mesh design and fabrication strategy toward ISEs for long-term continuous monitoring of water or wastewater quality.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/bios12100782
