An official website of the United States government
This study aimed to explore lignin as a naturally occurring aromatic precursor for the synthesis of LIG and further fabrication of ultrasensitive strain sensors for the detection of small deformations. One-step direct laser writing (DLW) induced high quality porous graphene, so called laser induced graphene (LIG), from kraft lignin under the conditions optimized for laser power, focus distance, and lignin loading. An electrode based on the resulting LIG was facilely fabricated by transferring LIG onto an elastomeric substrate ( i.e. , Dragon Skin™). The novel LIG transfer was facilitated by spin coating followed by water lifting, leading to the full retention of porous graphene onto the elastomeric substrate. The strain sensor was shown to be highly sensitive to small human body motions and tiny deformations caused by vibrations. It had a working range of up to 14% strain with a gauge factor of 960 and showed high stability as evidenced by repetitive signals over 10 000 cycles at 4% strain. The sensor was also successfully demonstrated for detecting human speaking, breath, seismocardiography (SCG), and movement of pulse and eye. Overall, the lignin-derived LIG can serve as excellent piezoresistive materials for wearable, stretchable, and ultrasensitive strain sensors with applications in human body motion monitoring and sound-related applications.
more »
« less
Direct Induction of Porous Graphene from Mechanically Strong and Waterproof Biopaper for On‐Chip Multifunctional Flexible Electronics
Abstract Graphene with a 3D porous structure is directly laser‐induced on lignocellulosic biopaper under ambient conditions and is further explored for multifunctional biomass‐based flexible electronics. The mechanically strong, flexible, and waterproof biopaper is fabricated by surface‐functionalizing cellulose with lignin‐based epoxy acrylate (LBEA). This composite biopaper shows as high as a threefold increase in tensile strength and excellent waterproofing compared with pure cellulose one. Direct laser writing (DLW) rapidly induces porous graphene from the biopaper in a single step. The porous graphene shows an interconnected carbon network, well‐defined graphene domains, and high electrical conductivity (e.g., ≈3 Ω per square), which can be tuned by lignin precursors and loadings as well as lasing conditions. The biopaper in situ embedded with porous graphene is facilely fabricated into flexible electronics for on‐chip and paper‐based applications. The biopaper‐based electronic devices, including the all‐solid‐state planer supercapacitor, electrochemical and strain biosensors, and Joule heater, show great performances. This study demonstrates the facile, versatile, and low‐cost fabrication of multifunctional graphene‐based electronics from lignocellulose‐based biopaper.
more »
« less
- Award ID(s):
- 1933861
- PAR ID:
- 10426647
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Small
- ISSN:
- 1613-6810
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Cost-effective valorization of biomass into advanced carbon remains a challenge. Here we reported a facile and ultrafast laser writing technique to convert biomass into porous graphene for electrochemical sensing. Laser-induced graphene (LIG) was synthesized from a fully biomass-based film composed of kraft lignin (KL) and cellulose nanofibers (CNFs). The LIG-based electrode was applied to detect dopamine using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. Dopamine with a concentration ranging from 5 to 40 μM was detected linearly, with a sensitivity of 4.39 μA μM −1 cm −2 . Our study eliminated the use of synthetic polymer for lignin-based film formation. It demonstrated the feasibility of using the film fully composed of biomass for LIG formation. Furthermore, derived LIG electrodes were shown to have high electrochemical sensing performance.more » « less
-
Abstract There are advantages to polymer/nanoparticle composite‐based volatile organic compounds (VOCs) sensors, such as high chemical and physical stability, operability under extreme conditions, flexible use in manufacturing, and low cost. Nevertheless, their lower limit of detection due to thickness‐dependent diffusion has constrained their application. Inspired by the metaxylem in vascular plants and its vertical conduits and horizontal pits that enable efficient transpiration, a polymer/nanoparticle composite‐based sensor is fabricated with a controllable, spontaneously formed, hollow core for inline VOCs transportation, and porous microstructure for radial direction diffusion. The hollow core is surrounded by an inner porous layer (thermoplastic polyurethane (TPU)), a middle sensing layer (TPU/graphene nanoplatelets/multiwalled carbon nanotubes), and an outer mechanically durable layer (TPU). This multilayered structure shows a 600% higher response rate compared to a single‐layered composite fiber sensor, with a low limit of detection (e.g., ≈15 ppm for xylene) and high selectivity based on the Flory–Huggins interaction parameter. This flexible and stretchable sensor also demonstrates a dual parameter sensing capability from VOC concentrations and uniaxial strain deformation. Via a one‐step fiber spinning procedure, this self‐induced hollow fiber offers a unique method of microstructural design, which enables the detection of low‐concentration VOCs by polymer/nanoparticle‐based sensors.more » « less
-
Lignin’s immiscibility with most polymers along with its unknown association behaviors are major factors that contribute to its disposal and processability for the production of materials. To fully utilize lignin, an improved understanding of its interaction with other materials is needed. In this study, we investigate the morphological and physicochemical properties upon the addition of reduced graphene oxide (rGO) as a function of material composition in a tertiary system comprised of lignin, cellulose and xylan. The main motivation for this work is to understand how the lignin molecule associates and behaves in the presence of other natural macromolecules, as well as with the addition of reduced graphene oxide. The fabricated biocomposites with and without rGO were investigated using Attenuated Total Reflectance Fourier Transform Infrared spectroscopy (ATR-FTIR), Scanning Electron Microscope (SEM) techniques, Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The results demonstrated that the regenerated films’ structural, morphological and thermal character changed as a function of lignin-xylan concentration and upon the addition of rGO. We also observed a dramatic change in the glass transition temperature and topography. Final analysis showed that the addition of rGO prevented the macromolecules to self-assemble through a reduction of π-π aggregations and changes in the cellulose crystallinity.more » « less
-
Abstract 3D conformable electronic devices on freeform surfaces show superior performance to the conventional, planar ones. They represent a trend of future electronics and have witnessed exponential growth in various applications. However, their potential is largely limited by a lack of sophisticated fabrication techniques. To tackle this challenge, a new direct freeform laser (DFL) fabrication method enabled by a 5‐axis laser processing platform for directly fabricating 3D conformable electronics on targeted arbitrary surfaces is reported. Accordingly, representative laser‐induced graphene (LIG), metals, and metal oxides are successfully fabricated as high‐performance sensing and electrode materials from different material precursors on various types of substrates for applications in temperature/light/gas sensing, energy storage, and printed circuit board for circuit. Last but not the least, to demonstrate an application in smart homes, LIG‐based conformable strain sensors are fabricated and distributed in designated locations of an artificial tree. The distributed sensors have the capability of monitoring the wind speed and direction with the assistance of well‐trained machine‐learning models. This novel process will pave a new and general route to fabricating 3D conformable electronic devices, thus creating new opportunities in robotics, biomedical sensing, structural health, environmental monitoring, and Internet of Things applications.more » « less
