An official website of the United States government
The ability to manufacture complex design geometries via Additive Manufacturing (AM) has led to a rapid growth in advancing the design methods, fabrication, and application of Triply Periodic Minimal Surface (TPMS) lattices with minimal surface topologies. Due to its zero-mean curvature, TPMS lattices can be additively manufactured without any sacrificial support structures and offer both design and manufacturing engineers, unprecedented control over the local physical properties (surface area, relative density, etc.) and local mechanical properties (flexural strength, Young’s modulus, etc.). TPMS lattices are of high interest for a wide range of applications such as biomedical implants, energy absorption, and surface fluidic applications such as heat exchangers, and energy storage. Recent advancements in functionally graded TPMS lattice design by varying local lattice geometry has shown to result in different mechanical performance. However, there have been limited studies in understanding the functional grading of AM process conditions (e.g., Laser-Powder Bed Fusion in this study) and lattice sheet thickness to better map the design-processing conditions-properties. The goal of this study is to achieve similar mechanical properties in TPMS sheet lattices with two different TPMS sheet thicknesses by varying laser processing conditions (e.g., contour and hatch conditions in this study). Quasi-static tensile testing of solid samples with corresponding AM conditions and 3-point bending tests of TPMS lattices were performed in accordance with ASTM E8 and ASTM E290, respectively. It was observed that the flexural properties of the 0.75 mm and 0.25 mm TPMS lattices are similar and exhibit different properties with different scan strategies and speed variations under contour-only and hatch-only laser scanning strategies. Also, the 0.75 mm TPMS sheet lattices exhibited 79 % higher flexural stiffness than the 0.25 mm sheet lattices. It was also observed that this observed trend was reversed in the case of tensile properties. Findings from this study can provide new directions towards achieving gradient TPMS lattice designs with varying local mechanical performance by grading the laser scanning strategies to achieve desired mechanical properties and surface topologies.
more »
« less
Mechanical Properties of Highly Deformable Elastomeric Gyroids for Multifunctional Capacitors
Triply periodic minimal surface lattices have mechanical properties that derive from the unit cell geometry and the base material. Through computation software like nTopology and Abaqus, these geometries are used to tune nonlinear stress–strain curves not readily achievable with solid materials alone and to change the compliance by two orders of magnitude compared to the constituent material. In this study, four elastomeric TPMS gyroids undergo large deformation compression and tension testing to investigate the impact of the structure's geometry on the mechanical properties. Among all the samples, the modulus at strainεvaries by over one order of magnitude (7.7–293.4 kPa from FEA under compression). These lattices are promising candidates for designing multifunctional systems that can perform multiple tasks simultaneously by leveraging the geometry's large surface area to volume ratio. For example, the architectural functionality of the lattice to bear loads and store mechanical energy along with the larger surface area for energy storage is combined. A compliant double‐gyroid capacitor that can simultaneously achieve three functions is demonstrated: load bearing, energy storage, and sensing.
more »
« less
- Award ID(s):
- 1825444
- PAR ID:
- 10432915
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Engineering Materials
- Volume:
- 25
- Issue:
- 19
- ISSN:
- 1438-1656
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Conducting polymer hydrogels combine electrical conductivity and tunable water content, rendering them strong candidates for a range of applications including biosensors, cell culture platforms, and energy storage devices. However, these hydrogels are mechanically brittle and prone to damage, prohibiting their use in emerging applications involving dynamic movement and large mechanical deformation. Here, we demonstrate that applying the concept of architecture to conducting polymer hydrogels can circumvent these impediments. A stereolithography 3D printing method is developed to successfully fabricate such hydrogels in complex lattice structures. The resulting hydrogels exhibit elastic compressibility, high fracture strain, enhanced cycling stability, and damage-tolerant properties despite their chemical composition being identical to their brittle, solid counterparts. Furthermore, concentrating the deformation to the 3D geometry, rather than polymer microstructure, effectively decouples the mechanical and electrical properties of the hydrogel lattices from their intrinsic properties associated with their chemical composition. The confluence of these new physical properties for conducting polymer hydrogels opens broad opportunities for a myriad of dynamic applications.more » « less
-
Additive manufacturing has provided the ability to manufacture complex structures using a wide variety of materials and geometries. Structures such as triply periodic minimal surface (TPMS) lattices have been incorporated into products across many fields due to their unique combinations of mechanical, geometric, and physical properties. Yet, the near limitless possibility of combining geometry and material into these lattices leaves much to be discovered. This article provides a dataset of experimentally gathered tensile stress-strain curves and measured porosity values for 389 unique gyroid lattice structures manufactured using vat photopolymerization 3D printing. The lattice samples were printed from one of twenty different photopolymer materials available from either Formlabs, LOCTITE AM, or ETEC that range from strong and brittle to elastic and ductile and were printed on commercially available 3D printers, specifically the Formlabs Form2, Prusa SL1, and ETEC Envision One cDLM Mechanical. The stress-strain curves were recorded with an MTS Criterion C43.504 mechanical testing apparatus and following ASTM standards, and the void fraction or “porosity” of each lattice was measured using a calibrated scale. This data serves as a valuable resource for use in the development of novel printing materials and lattice geometries and provides insight into the influence of photopolymer material properties on the printability, geometric accuracy, and mechanical performance of 3D printed lattice structures. The data described in this article was used to train a machine learning model capable of predicting mechanical properties of 3D printed gyroid lattices based on the base mechanical properties of the printing material and porosity of the lattice in the research article [1].more » « less
-
Abstract Articular cartilage (AC) is a load-bearing tissue that covers long bones in synovial joints. The biphasic/poroelastic mechanical properties of AC help it to protect joints by distributing loads, absorbing impact forces, and reducing friction. Unfortunately, alterations in these mechanical properties adversely impact cartilage function and precede joint degeneration in the form of osteoarthritis (OA). Thus, understanding what factors regulate the poroelastic mechanical properties of cartilage is of great scientific and clinical interest. Transgenic mouse models provide a valuable platform to delineate how specific genes contribute to cartilage mechanical properties. However, the poroelastic mechanical properties of murine articular cartilage are challenging to measure due to its small size (thickness ∼ 50 microns). In the current study, our objective was to test whether the poroelastic mechanical properties of murine articular cartilage can be determined based solely on time-dependent cell death measurements under constant loading conditions. We hypothesized that in murine articular cartilage subjected to constant, sub-impact loading from an incongruent surface, cell death area and tissue strain are closely correlated. We further hypothesized that the relationship between cell death area and tissue strain can be used—in combination with inverse finite element modeling—to compute poroelastic mechanical properties. To test these hypotheses, murine cartilage-on-bone explants from different anatomical locations were subjected to constant loading conditions by an incongruent surface in a custom device. Cell death area increased over time and scaled linearly with strain, which rose in magnitude over time due to poroelastic creep. Thus, we were able to infer tissue strain from cell death area measurements. Moreover, using tissue strain values inferred from cell death area measurements, we applied an inverse finite element modeling procedure to compute poroelastic material properties and acquired data consistent with previous studies. Collectively, our findings demonstrate in the key role poroelastic creep plays in mediating cell survival in mechanically loaded cartilage and verify that cell death area can be used as a surrogate measure of tissue strain that enables determination of murine cartilage mechanical properties.more » « less
-
Bowden, Ned (Ed.)Covalent organic framework (COF) aerogels arehierarchically porous polymeric materials with ultrahigh specific surface area, making them attractive for wide applications such as molecular capture, adsorption, and catalysis. Previous COF aerogel studies have focused on varying their chemical structures and linkage chemistries to fine-tune material properties and functionality, most of which have reported relatively unsatisfying performance (e.g., poor mechanical strength and strain tolerance). This study describes the synthesis and characterization of COF nanocomposite aerogels, whose material properties and functionality are effectively engineered through the incorporation of reinforcing fillers/binders or functional additives. Boron nitride (BN) fillers, cross-linked poly(acrylic acid) (XPAA) binders, and gold nanoparticles (AuNps) are incorporated into 1,3,5-tris(aminophenyl)benzene-terephthaldehyde (TAPB-PDA) COF aerogel matrices to form homogeneous nanocomposite aerogels with enhanced mechanical properties and unique photothermal conversion capabilities. Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, and scanning electron microscopy results confirm the successful filler/additive inclusion into the final COF nanocomposite aerogels. Specifically, BN filler loading at ∼17 wt % relative to final COF mass doubles COF aerogel’s Young’s modulus from 11 to 22 kPa according to mechanical compression tests, with only ∼10% reduction in COF’s accessible mesopores’ surface area according to nitrogen porosimeter analyses. Meanwhile, incorporating ∼7 wt % XPAA relative to final COF mass improves the Young’s modulus to 21 kPa, while increasing the aerogel’s yield strain from 10 to 65% strain, although this leads to a ∼35% reduction in COF’s accessible mesopores’ surface area. Furthermore, photothermal AuNps are incorporated to form functional COF nanocomposite aerogels, whose overall temperature increases by 5.5 °C after 1 sun (AM1.5G, 1000 W m−2) irradiation. Overall, this study demonstrates potential routes to fabricate hierarchically porous COF nanocomposite aerogels with high specific surface area, robust mechanical stability, and unique photothermal functionality, which hold promises for applications in adsorption separation, gas storage, and photocatalysis.more » « less
