skip to main content

Explore Research Products in the NSF-PAR

Title: Metal–organic framework ‐based mixed‐matrix membranes for gas separation: An overview
Abstract

Mixed‐matrix membranes (MMMs) have been studied widely in the field of gas separation due to their potential to overcome performance barriers found in traditional polymeric membranes. Most polymeric membranes exhibit a trade‐off between permeation and selectivity, which has limited their development in many challenging separation applications. One solution to this issue utilizes the introduction of fillers into the polymer matrix to produce MMMs. Out of the many different fillers, metal–organic frameworks stand out as a promising candidate due to their highly tunable structure, molecular sieving effect, and superior compatibility with the polymer matrix. This review will provide an in‐depth look into the basic mechanisms of MMMs for gas separation and different approaches to model the permeation of gases through the membrane. In addition, challenges facing the field and recent research trends for MMMs will be discussed as well as their many applications for different gas separations. Finally, some insight on the future direction for MMMs will be covered, focusing on many intriguing opportunities and challenges that must be further explored to advance this technology.

  more » « less
NSF-PAR ID:
10453941
Author(s) / Creator(s):
 ;  ;  ;  ;  ;  ;  ;  
Publisher / Repository:
Wiley Blackwell (John Wiley & Sons)
Date Published:
Journal Name:
Journal of Polymer Science
Volume:
58
Issue:
18
ISSN:
2642-4150
Page Range / eLocation ID:
p. 2518-2546
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ( , Journal of Materials Chemistry A)
    null (Ed.)
    Polymer-modification-enabled in situ metal–organic framework formation (PMMOF) is potentially a paradigm-shifting preparation method for polymer/MOF mixed-matrix membranes (MMMs). However, the actual reaction conditions of the in situ formation of MOFs in a confined polymer free volume are expected to be quite different from that in a bulk solution. ZIF-7 is an interesting filler material not only due to its use in selective light gas separations but also for its three different crystal phases. Herein, we carried out systematic investigations on the in situ confined formation of ZIF-7 phases inside a polymer (6FDA-DAM) by PMMOF. The reaction conditions of ZIF-7 in the polymer free volume were deduced based on a bulk-phase ZIF-7 phase diagram constructed by varying the ZIF-7 precursor concentrations and ratios. Based on the understanding of the reaction conditions, the ZIF-7 crystal phases formed inside the polymer during the PMMOF process were controlled, yielding 6FDA-DAM/ZIF-7 MMMs with three different crystal phases. The ZIF-7 phases had significant effects on the gas transport of MMMs with layered ZIF-7-III fillers exhibiting the highest performance enhancement for H 2 /CO 2 separation ( i.e. , H 2 permeability of ∼1630 Barrer and H 2 /CO 2 selectivity of ∼3.8) among other phases. Furthermore, the MMMs obtained by the PMMOF process showed enhanced H 2 /CO 2 separation performance, surpassing the upper bound. 
    more » « less
  2. ; ; ; ( , Energy & Environmental Science)
    Polymeric membranes are being studied for their potential use in post-combustion carbon capture on the premise that they could dramatically lower costs relative to mature technologies available today. Mixed matrix membranes (MMMs) are advanced materials formed by combining polymers with inorganic particles. Using metal–organic frameworks (MOFs) as the inorganic particles has been shown to improve selectivity and permeability over pure polymers. We have carried out high-throughput atomistic simulations on 112 888 real and hypothetical metal–organic framework structures in order to calculate their CO 2 permeabilities and CO 2 /N 2 selectivities. The CO 2 /H 2 O sorption selectivity of 2 017 real MOFs was evaluated using the H 2 O sorption data of Li et al. (S. Li, Y. G. Chung and R. Q. Snurr, Langmuir , 2016, 32 , 10368–10376). Using experimentally measured polymer properties and the Maxwell model, we predicted the properties of all of the hypothetical mixed matrix membranes that could be made by combining the metal–organic frameworks with each of nine polymers, resulting in over one million possible MMMs. The predicted gas permeation of MMMs was compared to published gas permeation data in order to validate the methodology. We then carried out twelve individually optimized techno-economic evaluations of a three-stage membrane-based capture process. For each evaluation, capture process variables such as flow rate, capture fraction, pressure and temperature conditions were optimized and the resultant cost data were interpolated in order to assign cost based on membrane selectivity and permeability. This work makes a connection from atomistic simulation all the way to techno-economic evaluation for a membrane-based carbon capture process. We find that a large number of possible mixed matrix membranes are predicted to yield a cost of carbon capture less than $50 per tonne CO 2 removed, and a significant number of MOFs so identified have favorable CO 2 /H 2 O sorption selectivity. 
    more » « less
  3. ; ; ; ; ; ; ; ; ; ( , Advanced Functional Materials)
    Abstract

    Mixed matrix membranes (MMMs) comprising size‐sieving fillers dispersed in polymers exhibit diffusivity selectivity and may surpass the upper bound for gas separation, but their performance is limited by defects at the polymer/filler interface. Herein, a fundamentally different approach employing a highly sorptive filler that is inherently less sensitive to interfacial defects is reported. Palladium nanoparticles with extremely high H2sorption are dispersed in polybenzimidazole at loadings near the percolation threshold, which increases both H2permeability and H2/CO2selectivity. Performance of these MMMs surpasses the state‐of‐the‐art upper bound for H2/CO2separation with polymer‐based membranes. The success of these sorption‐enhanced MMMs for H2/CO2separation may launch a new research paradigm that taps the enormous knowledge of affinities between gases and nanomaterials to design MMMs for a wide variety of gas separations.

     
    more » « less
  4. ; ; ; ( , Advanced Materials Technologies)
    Abstract

    Water pollution is a major global challenge, as conventional polymeric membranes are not adequate for water treatment anymore. Among emerging materials for water treatment, composite membranes are promising, as they have simultaneously improved water permeation and ions rejection. Recently, a new family of 2D materials called MXenes has attracted considerable attention due to their appealing properties and wide applications. MXenes can be incorporated into many polymeric materials due to their high compatibility. MXenes/polymer composite membranes have been found to have appealing electrical, thermal, mechanical, and transport properties, because of strong interactions between polymer chains and surface functional groups of MXenes and the selective nanochannels that are created. This article reviews advances made in the area of ion‐selective MXene‐based membranes for water purification. It puts the advances into perspective and provides prospects. MXenes’ properties and synthesis methods are briefly described. Strategies for the preparation of MXene‐based membranes including mixed‐matrix membranes, thin‐film nanocomposite membranes, and laminated membranes are reviewed. Recent advances in ion‐separation and water‐desalination MXene‐based membranes are elucidated. The dependence of ion‐separation performance of the membranes on fabrication techniques, MXene's interlayer spacing, and MXene's various surface terminations are elucidated. Finally, opportunities and challenges in ion‐selective MXene‐based membranes are discussed.

     
    more » « less
  5. ; ; ; ; ; ; ; ; ( , Applied Sciences)
    Polymers are increasingly being used in higher demanding applications due to their ability to tailor the properties of structures while allowing for a weight and cost reduction. Solvents play an important role in the manufacture of polymeric structures since they allow for a reduction in the polymer’s viscosity or assist with the dispersion of fillers into the polymer matrix. However, the incorrect removal of the solvent affects both the physical and chemical properties of polymeric materials. The presence of residual solvent can also negatively affect the curing kinetics and the final quality of polymers. Destructive testing is mainly performed to characterize the properties of these materials. However, this type of testing involves using lab-type equipment that cannot be taken in-field to perform in situ testing and requires a specific sample preparation. Here, a method is presented to non-destructively evaluate the curing process and final viscoelastic properties of polymeric materials using ultrasonics. In this study, changes in longitudinal sound speed were detected during the curing of an aerospace epoxy adhesive as a result of variations in polymer chemistry. To simulate the presence of residual solvent, samples containing different weight percentages of isopropyl alcohol were manufactured and tested using ultrasonics. Thermogravimetric analysis was used to show changes in the decomposition of the adhesive due to the presence of IPA within the polymer structure. Adding 2, 4, and 6 wt.% of IPA decreased the adhesive’s lap shear strength by 40, 58, and 71%, respectively. Ultrasonics were used to show how the solvent influenced the curing process and the final sound speed of the adhesive. Young’s modulus and Poisson’s ratio were determined using both the longitudinal and shear sound speeds of the adhesive. Using ultrasonics has the potential to non-invasively characterize the quality of polymers in both an in-field and manufacturing settings, ensuring their reliability during use in demanding applications. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email