In its initial phase in 2009, the inorganic‐organic hybrid perovskite solar cells (PSCs) delivered a 3.8% power conversion efficiency (PCE), which is far below the present 25.7% PCE obtained in 2022. The significant improvement of the efficiency of PSCs in such a short period has stimulated significant interest in the photovoltaic community. However, the performance of current PSCs is behind the commercially available and widely used solar cells in terms of stability and scalability. Among various commonly studied perovskite materials, methylammonium lead iodide (MAPbI3) is the most widely studied. This review will focus on the common solar cell structures (mesoporous, inverted planar p‐i‐n, planar n‐i‐p) using MAPbI3perovskite as an active layer and the effect of these solar cell structures on their performances. Furthermore, some commonly‐used strategies are outlined for improving the device performance, such as optimizing the deposition technique of the charge transporting and the active layers, modifying the properties of the carrier transporting layer and the perovskite layer by interface engineering and doping, optimizing the perovskite surface morphology, along with others. This article will also discuss the hole transport free and electron transport free MAPbI3PSCs.
Typical lead‐based perovskites solar cells show an onset of photogeneration around 800 nm, leaving plenty of spectral loss in the near‐infrared (NIR). Extending light absorption beyond 800 nm into the NIR should increase photocurrent generation and further improve photovoltaic efficiency of perovskite solar cells (PSCs). Here, a simple and facile approach is reported to incorporate a NIR‐chromophore that is also a Lewis‐base into perovskite absorbers to broaden their photoresponse and increase their photovoltaic efficiency. Compared with pristine PSCs without such an organic chromophore, these solar cells generate photocurrent in the NIR beyond the band edge of the perovskite active layer alone. Given the Lewis‐basic nature of the organic semiconductor, its addition to the photoactive layer also effectively passivates perovskite defects. These films thus exhibit significantly reduced trap densities, enhanced hole and electron mobilities, and suppressed illumination‐induced ion migration. As a consequence, perovskite solar cells with organic chromophore exhibit an enhanced efficiency of 21.6%, and substantively improved operational stability under continuous one‐sun illumination. The results demonstrate the potential generalizability of directly incorporating a multifunctional organic semiconductor that both extends light absorption and passivates surface traps in perovskite active layers to yield highly efficient and stable NIR‐harvesting PSCs.
more » « less- Award ID(s):
- 1824674
- NSF-PAR ID:
- 10459211
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials
- Volume:
- 31
- Issue:
- 49
- ISSN:
- 0935-9648
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Perovskite solar cells in which 2D perovskites are incorporated within a 3D perovskite network exhibit improved stability with respect to purely 3D systems, but lower record power conversion efficiencies (PCEs). Here, a breakthrough is reported in achieving enhanced PCEs, increased stability, and suppressed photocurrent hysteresis by incorporating n‐type, low‐optical‐gap conjugated organic molecules into 2D:3D mixed perovskite composites. The resulting ternary perovskite–organic composites display extended absorption in the near‐infrared region, improved film morphology, enlarged crystallinity, balanced charge transport, efficient photoinduced charge transfer, and suppressed counter‐ion movement. As a result, the ternary perovskite–organic solar cells exhibit PCEs over 23%, which are among the best PCEs for perovskite solar cells with p–i–n device structure. Moreover, the ternary perovskite–organic solar cells possess dramatically enhanced stability and diminished photocurrent hysteresis. All these results demonstrate that the strategy of exploiting ternary perovskite–organic composite thin films provides a facile way to realize high‐performance perovskite solar cells.
-
more » « less
Abstract Perovskite‐organic tandem solar cells are attracting more attention due to their potential for highly efficient and flexible photovoltaic device. In this work, efficient perovskite‐organic monolithic tandem solar cells integrating the wide bandgap perovskite (1.74 eV) and low bandgap organic active PBDB‐T:SN6IC‐4F (1.30 eV) layer, which serve as the top and bottom subcell, respectively, are developed. The resulting perovskite‐organic tandem solar cells with passivated wide‐bandgap perovskite show a remarkable power conversion efficiency (PCE) of 15.13%, with an open‐circuit voltage (
V oc) of 1.85 V, a short‐circuit photocurrent (J sc) of 11.52 mA cm−2, and a fill factor (FF) of 70.98%. Thanks to the advantages of low temperature fabrication processes and the flexibility properties of the device, a flexible tandem solar cell which obtain a PCE of 13.61%, withV ocof 1.80 V,J scof 11.07 mA cm−2, and FF of 68.31% is fabricated. Moreover, to demonstrate the achieved highV ocin the tandem solar cells for potential applications, a photovoltaic (PV)‐driven electrolysis system combing the tandem solar cell and water splitting electrocatalysis is assembled. The integrated device demonstrates a solar‐to‐hydrogen efficiency of 12.30% and 11.21% for rigid, and flexible perovskite‐organic tandem solar cell based PV‐driven electrolysis systems, respectively. -
more » « less
Ternary organic solar cells, a single active layer comprising three different components, are demonstrated to be one of the most efficient ways to approach high‐performance organic solar cells. But nevertheless, most of the ternary organic solar cells are characterized by steady‐state measurements, which are helpful but inadequate to fully understand the underlying charge carrier behavior at a short time scale. Herein, a comparison of the steady‐state and time‐dependent measurements is used to investigate the functionality of non‐fullerene electron acceptors in ternary organic solar cells. The steady‐state measurements indicate that non‐fullerene electron acceptors enlarge the absorption range of the photoactive layer, suppress charge carrier recombination, reduce charge carrier transfer resistance, and thereby increase photocurrent in ternary organic solar cells. The time‐dependent measurements demonstrate that a short charge carrier extraction time and a high charge carrier mobility are responsible for enhanced photocurrent in ternary organic solar cells. A comprehensive method understanding the underlying of enhanced efficiency of ternary organic solar cells is provided herein.
-
more » « less
Abstract Perovskite solar cells (PSCs) have rapidly emerged as one of the hottest topics in the photovoltaics community owing to their high power‐conversion efficiencies (PCE), and the promise to be produced at low cost. Among various PSCs, typical 3D perovskite‐based solar cells deliver high PCE but they suffer from severe instability, which restricts their practical applications. In contrast to 3D perovskites, 2D perovskites that incorporate larger, less volatile, and generally more hydrophobic organic cations exhibit much improved thermal, chemical, and environmental stability. 2D perovskites can have different roles within a solar cell, either as the primary light absorber (2D PSCs), or as a capping layer atop a 3D perovskite absorbing layer (2D/3D PSCs). Tradeoffs between PCE and stability exist in both types of PSCs—2D PSCs are more stable but exhibit lower efficiency while 2D/3D PSCs deliver exciting efficiency but show relatively poor stability. To address this PCE/stability tradeoff, the challenges both the 2D and 2D/3D PSCs face are identified and select works the community has undertaken to overcome them are highlighted in this review. It is ended with several recommendations on how to further improve PSCs so their performance and stability can be commensurate with application requirements.
