Hybrid halide 2D perovskites deserve special attention because they exhibit superior environmental stability compared with their 3D analogs. The closer interlayer distance discovered in 2D Dion–Jacobson (DJ) type of halide perovskites relative to 2D Ruddlesden–Popper (RP) perovskites implies better carrier charge transport and superior performance in solar cells. Here, the structure and properties of 2D DJ perovskites employing 3‐(aminomethyl)piperidinium (3AMP2+) as the spacing cation and a mixture of methylammonium (MA+) and formamidinium (FA+) cations in the perovskite cages are presented. Using single‐crystal X‐ray crystallography, it is found that the mixed‐cation (3AMP)(MA0.75FA0.25)3Pb4I13perovskite has a narrower bandgap, less distorted inorganic framework, and larger PbIPb angles than the single‐cation (3AMP)(MA)3Pb4I13. Furthermore, the (3AMP)(MA0.75FA0.25)3Pb4I13films made by a solvent‐engineering method with a small amount of hydriodic acid have a much better film morphology and crystalline quality and more preferred perpendicular orientation. As a result, the (3AMP)(MA0.75FA0.25)3Pb4I13‐based solar cells exhibit a champion power conversion efficiency of 12.04% with a high fill factor of 81.04% and a 50% average efficiency improvement compared to the pristine (3AMP)(MA)3Pb4I13cells. Most importantly, the 2D DJ 3AMP‐based perovskite films and devices show better air and light stability than the 2D RP butylammonium‐based perovskites and their 3D analogs.
Perovskite solar cells are one of the most promising photovoltaic technologies, although their molecular level design and stability toward environmental factors remain a challenge. Layered 2D Ruddlesden–Popper perovskite phases feature an organic spacer bilayer that enhances their environmental stability. Here, the concept of supramolecular engineering of 2D perovskite materials is demonstrated in the case of formamidinium (FA) containing A2FA
- NSF-PAR ID:
- 10461347
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Energy Materials
- Volume:
- 9
- Issue:
- 20
- ISSN:
- 1614-6832
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Dion–Jacobson (DJ) phase 2D layered perovskites with diammonium organic cations demonstrate improved stability over 3D perovskites under thermal/photo/moisture stresses. However, the power conversion efficiency (PCE) of DJ phase perovskite solar cells (PVSCs) is often limited by the poor charge transport across the perovskite layers due to the crystal growth direction that tends to be parallel to the substrate. Here, a simple and effective method is demonstrated by employing a NH4SCN additive to facilitate the orientation of perovskite crystal growth to be perpendicular to the substrate. Also, the layer number distribution can be narrowed to around
n = 3 andn = 4 with NH4SCN addition. The device derived from the quasi‐2D DJ (BDA)(MA)4Pb5I16perovskite film processed with NH4SCN shows a PCE of 14.53%, which is among the highest values reported for 2D PVSCs prepared at room temperature. Moreover, the device retains 85% of its initial PCE after 900 h storage in ambient conditions with a humidity level of 50 ± 5%. These results demonstrate that this attractive approach will enable highly efficient and stable PVSCs to be made for renewable energy applications. -
more » « less
Abstract Next‐generation electronics and energy technologies can now be developed as a result of the design, discovery, and development of novel, environmental friendly lead (Pb)‐free ferroelectric materials with improved characteristics and performance. However, there have only been a few reports of such complex materials’ design with multi‐phase interfacial chemistry, which can facilitate enhanced properties and performance. In this context, herein, novel lead‐free piezoelectric materials (1‐
x )Ba0.95Ca0.05Ti0.95Zr0.05O3‐(x )Ba0.95Ca0.05Ti0.95Sn0.05O3, are reported, which are represented as (1‐x )BCZT‐(x )BCST, with demonstrated excellent properties and energy harvesting performance. The (1‐x )BCZT‐(x )BCST materials are synthesized by high‐temperature solid‐state ceramic reaction method by varyingx in the full range (x = 0.00–1.00). In‐depth exploration research is performed on the structural, dielectric, ferroelectric, and electro‐mechanical properties of (1‐x )BCZT‐(x )BCST ceramics. The formation of perovskite structure for all ceramics without the presence of any impurity phases is confirmed by X‐ray diffraction (XRD) analyses, which also reveals that the Ca2+, Zr4+, and Sn4+are well dispersed within the BaTiO3lattice. For all (1‐x )BCZT‐(x )BCST ceramics, thorough investigation of phase formation and phase‐stability using XRD, Rietveld refinement, Raman spectroscopy, high‐resolution transmission electron microscopy (HRTEM), and temperature‐dependent dielectric measurements provide conclusive evidence for the coexistence of orthorhombic + tetragonal (Amm2 +P4mm ) phases at room temperature. The steady transition ofAmm2 crystal symmetry toP4mm crystal symmetry with increasingx content is also demonstrated by Rietveld refinement data and related analyses. The phase transition temperatures, rhombohedral‐orthorhombic (TR‐O), orthorhombic‐ tetragonal (TO‐T), and tetragonal‐cubic (TC), gradually shift toward lower temperature with increasingx content. For (1‐x )BCZT‐(x )BCST ceramics, significantly improved dielectric and ferroelectric properties are observed, including relatively high dielectric constantε r≈ 1900–3300 (near room temperature),ε r≈ 8800–12 900 (near Curie temperature), dielectric loss, tanδ ≈ 0.01–0.02, remanent polarizationP r≈ 9.4–14 µC cm−2, coercive electric fieldE c≈ 2.5–3.6 kV cm−1. Further, high electric field‐induced strainS ≈ 0.12–0.175%, piezoelectric charge coefficientd 33≈ 296–360 pC N−1, converse piezoelectric coefficient ≈ 240–340 pm V−1, planar electromechanical coupling coefficientk p≈ 0.34–0.45, and electrostrictive coefficient (Q 33)avg≈ 0.026–0.038 m4C−2are attained. Output performance with respect to mechanical energy demonstrates that the (0.6)BCZT‐(0.4)BCST composition (x = 0.4) displays better efficiency for generating electrical energy and, thus, the synthesized lead‐free piezoelectric (1‐x )BCZT‐(x )BCST samples are suitable for energy harvesting applications. The results and analyses point to the outcome that the (1‐x )BCZT‐(x )BCST ceramics as a potentially strong contender within the family of Pb‐free piezoelectric materials for future electronics and energy harvesting device technologies. -
more » « less
2D Ruddlesden–Popper perovskites have risen to prominence as stable and efficient photovoltaic materials because of their structural diversity, rich photophysics, and low moisture ingression. However, thin films processed from stoichiometric precursor solutions possess a broad phase distribution of different number of inorganic layers with random crystal orientation, crippling device performance. The effect of methylammonium chloride (MACl) and 3‐amino‐4‐phenolsulfonic acid (APSA) on the fabrication of perpendicularly oriented (PEA)2MA4Pb5I16films with narrow phase distribution using antisolvent and hot‐casting processing techniques is investigated. MACl plays a critical role in suppressing parasitic
n ≤ 2 and 3D‐like phases. APSA performs the dual function of trap passivation and further narrowing phase polydispersity through strong coordination with Pb2+. Ex situ grazing‐incident wide‐angle X‐Ray scattering (GIWAXS) and ultrafast spectroscopic characterization reveal uniformly mixed‐phase distribution with disordered orientation in antisolvent treated films, while additive‐assisted hot‐casting treatment results in oriented, reverse‐graded phase distribution, i.e., small‐n on the film surface and large‐n at the bottom. Arising thin films enable efficient p–i–n solar cells with an efficiency of 14.34%, and aV ocof 1.20 V, retaining 96% initial efficiency after 1440 h under ambient conditions (RH = 50–60%) without encapsulation. -
The remarkable optoelectronic properties of metal halide perovskites have generated intense research interest over the last few years. The ability to control and manipulate the crystallisation and stoichiometry of perovskite thin-films has allowed for impressive strides in the development of highly efficient perovskite solar cells. However, being able to effectively modify the interfaces of metal halide perovskites, and to controllably p- or n-type dope the surfaces, may be key to further improvements in the efficiency and long-term stability of these devices. In this study, we use surface doping of the mixed-cation, mixed-halide perovskite FA 0.85 MA 0.15 Pb(I 0.85 Br 0.15 ) 3 (FA – formamidinium; MA – methylammonium) to improve the hole extraction from the perovskite solar cell. By treating the surface of the perovskite film with a strongly oxidizing molybdenum tris(dithiolene) complex, we achieve a shift in the work function that is indicative of p-doping, and a twofold increase in the total conductivity throughout the film. We probe the associated interfacial chemistry through photoelectron and solid-state nuclear magnetic resonance spectroscopies and confirm that charge-transfer occurs between the perovskite and dopant complex. The resulting p-doped interface constitutes a homojunction with increased hole-selectivity. With charge-selective layers, we show that this surface doping enhances the device performance of perovskite solar cells resulting in steady-state efficiencies approaching 21%. Finally, we demonstrate that a surface treatment with this dopant produces the same effect as the commonly employed additive 4- tert butylpyridine ( t BP), allowing us to achieve “ t BP-free” devices with steady-state efficiencies of over 20%, and enhanced thermal stability as compared to devices processed using t BP. Our findings therefore demonstrate that molecular doping is a feasible route to tune and control the surface properties of metal halide perovskites.more » « less
