Fresnel lens arrays are widely employed in concentrator photovoltaics, photonic devices, and integral imaging systems. In this study, a rapid non-isothermal imprinting process for Fresnel lens arrays was proposed. In this process, a heated mold with microstructures was momentarily pressed onto a thermoplastic polymer surface that was initially kept at room temperature. The microstructures of the mold can be copied completely to the polymer substrate by imprinting consecutively until a continuous surface Fresnel lens array is obtained. Different from more traditional molding processes, the substrate does not need to be heated and cooled repeatedly in the replicating process. In addition, the imprinting process is carried out at room temperature, which can greatly reduce the thermal cycle time and energy consumption. Generally speaking, the material flow and stress distribution of the substrate need to be monitored so that the microlenses with a high precision surface finish can be produced in the non-isothermal imprinting process. To verify this, the finite element method (FEM) model for the non-isothermal process was established, and the feasibility of this process was analyzed. A hexagonal continuous surface Fresnel lens array was then fabricated, and its geometrical contour and imaging performance were tested. The experimental results showed this new process could be an effective and low-cost optical fabrication technology for high-quality production of Fresnel lens arrays.
- Award ID(s):
- 2018853
- NSF-PAR ID:
- 10476248
- Publisher / Repository:
- Embry-Riddle Aeronautical University Scholarly Commons
- Date Published:
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
Abstract: Waste energy harvest using thermoelectric (TE) materials will be a potential solution to the serious environmental pollution and energy shortage problems. Due to limitations of current manufacturing techniques in geometry complexity and high density, TE devices are not widely utilized in daily life to gather waste energy. 3D printing brings an opportunity to solve the fabrication limitations. In this paper, a hybrid process was developed to fabricate thermoelectric materials by integrating hot pressing with stereolithography. The mold and punch were designed and printed to fabricate thermoelectric devices used on hot water tubes via stereolithography. The Sb2Te3 powders filled the 3D printed mold in a layered manner, and each layer of powders was compacted under the pressing of punch at a certain temperature and compressive force. The polymer mold was removed after the sintering process to form the final TE components. A series of experiments were conducted to identify the optimal heating temperature and compressive force. The microstructures morphology and electrical conductivity of fabricated Sb2Te3 samples were evaluated. This research work conducted a scientific investigation into the fabrication of TE material with a hybrid process, including hot pressing and 3D printing, to solve the current manufacturing challenges, providing perspectives on developments of TE devices used in various energy harvest applications.more » « less
-
more » « less
Abstract Shrink lithography is a promising top‐down micro/nanofabrication technique capable of miniaturizing patterns/structures to scales much smaller than the initial mold, however, rapid inexpensive fabrication of high‐fidelity shrinkable microfeatures remains challenging. This work reports the discovery and characterization of a simple, fast, low‐cost method for replicating and miniaturizing intricate micropatterns/structures on commodity heat‐shrinkable polymers. Large‐area permanent micropatterning on polystyrene and polyolefin shrink film is attained in one step under ambient conditions through brief irradiation by a shortwave UV pencil lamp. After baking briefly in an oven, the film shrinks biaxially and the miniaturized micropatterns emerge with significantly reduced surface area (up to 95%) and enhanced depth profile. The entire UV‐micropatterned miniaturization process is highly reproducible and achievable on benchtop under a few minutes without chemicals or sophisticated apparatus. A variety of microgrid patterns are replicated and miniaturized with high yield and resolution on both planar and curved surfaces. Sequential UV exposures enable easy and rapid engineering of sophisticated microtopography with miniaturized, multiscale, multidimensional microstructures. UV–ozone micropatterned polystyrene surfaces are well‐suited for lab‐on‐a‐chip analytical applications owing to the inherent biocompatibility and enhanced surface hydrophilicity. Miniaturization of dense, periodic micropatterns may facilitate low‐cost prototyping of functional devices/surfaces such as micro‐optics/sensors and tunable metamaterials.
-
more » « less
Graphene interacts with electromagnetic waves strongly in a wide range from ultra-violet to far-infrared, making the graphene coating suitable for a variety of applications. In this study, a novel localized rapid heating technique utilizing micro-patterned silicon stampers with carbide-bonded graphene coating, which directly heats up by absorbing mid-infrared light radiation, is implemented in rapid precision optical molding. The graphene network, as a functional coating to obtain thermal energy and improve the anti-adhesion of the mold surface, can heat up the mold surface rapidly (up to 18.16 K/s) and evenly above glass transition temperature over a large area within several seconds. Since the graphene coating was around tens of nanometers (∼45 nm) thick, the rapid precision surface molding process can be shortened into tens of seconds. Furthermore, the thermal response and repeatability of the graphene coated silicon wafer is investigated by repeated thermal cycling. This novel rapid precision surface molding technique is successfully tested to replicate grating structures and periodic patterns from silicon molds to thermoplastic substrates with high accuracy. Compared with conventional methods, this new approach can achieve much higher replication fidelity with a shorter cycle time and lower energy consumption.
-
more » « less
Abstract Periodic micro/nanoscale structures from nature have inspired the scientific community to adopt surface design for various applications, including superhydrophobic drag reduction. One primary concern of practical applications of such periodic microstructures remains the scalability of conventional microfabrication technologies. This study demonstrates a simple template‐free scalable manufacturing technique to fabricate periodic microstructures by controlling the ribbing defects in the forward roll coating. Viscoelastic composite coating materials are designed for roll‐coating using carbon nanotubes (CNT) and polydimethylsiloxane (PDMS), which helps achieve a controllable ribbing with a periodicity of 114–700 µm. Depending on the process parameters, the patterned microstructures transition from the linear alignment to a random structure. The periodic microstructure enables hydrophobicity as the water contact angles of the samples ranged from 128° to 158°. When towed in a static water pool, a model boat coated with the microstructure film shows 7%–8% faster speed than the boat with a flat PDMS film. The CNT addition shows both mechanical and electrical properties improvement. In a mechanical scratch test, the cohesive failure of the CNT‐PDMS film occurs in ≈90% higher force than bare PDMS. Moreover, the nonconductive bare PDMS shows sheet resistance of 747.84–22.66 Ω □−1with 0.5 to 2.5 wt% CNT inclusion.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Workshop Report:
- The DOI is not currently available.
