In this study, a novel fabrication process, to the best of our knowledge, was developed to fabricate a glass harmonic diffractive lens. In this process, a polymethylmethacrylate master of the diffractive lens was machined using single-point diamond turning. Then an electrolytic plating process was conducted to grow a reverse nickel (Ni) mold. Precision compression molding was performed using the Ni mold to replicate the diffractive lens structures onto a glass surface. Surface measurements and optical testing show that the replicated diffractive lenses by the proposed method have high tolerances and require optical performance, demonstrating a high-volume, high-precision, and cost-effective process. The proposed method will be critical for consumer products where glass optics are increasingly used in lens assemblies.
- PAR ID:
- 10097967
- Date Published:
- Journal Name:
- Optical Manufacturing and Testing XII
- Volume:
- 10742
- Page Range / eLocation ID:
- 28
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Abstract 3D printing of optics has gained significant attention in optical industry, but most of the research has been focused on organic polymers. In spite of recent progress in 3D printing glass, 3D printing of precision glass optics for imaging applications still faces challenges from shrinkage during printing and thermal processing, and from inadequate surface shape and quality to meet the requirements for imaging applications. This paper reports a new liquid silica resin (LSR) with higher curing speed, better mechanical properties, lower sintering temperature, and reduced shrinkage, as well as the printing process for high‐precision glass optics for imaging applications. It is demonstrated that the proposed material and printing process can print almost all types of optical surfaces, including flat, spherical, aspherical, freeform, and discontinuous surfaces, with accurate surface shape and high surface quality for imaging applications. It is also demonstrated that the proposed method can print complex optical systems with multiple optical elements, completely removing the time‐consuming and error‐prone alignment process. Most importantly, the proposed printing method is able to print optical systems with active moving elements, significantly improving system flexibility and functionality. The printing method will enable the much‐needed transformational manufacturing of complex freeform glass optics that are currently inaccessible with conventional processes.
-
more » « less
Freeform optical components enable dramatic advances for optical systems in both performance and packaging. Surface form metrology of manufactured freeform optics remains a challenge and an active area of research. Towards addressing this challenge, we previously reported on a novel architecture, cascade optical coherence tomography (C-OCT), which was validated for its ability of high-precision sag measurement at a given point. Here, we demonstrate freeform surface measurements, enabled by the development of a custom optical-relay-based scanning mechanism and a unique high-speed rotation mechanism. Experimental results on a flat mirror demonstrate an RMS flatness of 14 nm (∼λ/44 at the He-Ne wavelength). Measurement on a freeform mirror is achieved with an RMS residual of 69 nm (∼λ/9). The system-level investigations and validation provide the groundwork for advancing C-OCT as a viable freeform metrology technique.
-
more » « less
Fresnel lens arrays are widely employed in concentrator photovoltaics, photonic devices, and integral imaging systems. In this study, a rapid non-isothermal imprinting process for Fresnel lens arrays was proposed. In this process, a heated mold with microstructures was momentarily pressed onto a thermoplastic polymer surface that was initially kept at room temperature. The microstructures of the mold can be copied completely to the polymer substrate by imprinting consecutively until a continuous surface Fresnel lens array is obtained. Different from more traditional molding processes, the substrate does not need to be heated and cooled repeatedly in the replicating process. In addition, the imprinting process is carried out at room temperature, which can greatly reduce the thermal cycle time and energy consumption. Generally speaking, the material flow and stress distribution of the substrate need to be monitored so that the microlenses with a high precision surface finish can be produced in the non-isothermal imprinting process. To verify this, the finite element method (FEM) model for the non-isothermal process was established, and the feasibility of this process was analyzed. A hexagonal continuous surface Fresnel lens array was then fabricated, and its geometrical contour and imaging performance were tested. The experimental results showed this new process could be an effective and low-cost optical fabrication technology for high-quality production of Fresnel lens arrays.
-
more » « less
Dynamic illumination using tunable freeform arrays can enable spatial light distributions of variable size with high uniformity from non-uniform sources through relatively small opposing lateral shifts applied to the freeform components. We present the design, manufacturing, and characterization of a tunable LED-based illuminator using custom freeform Alvarez arrays with commercially available optics to shorten the manufacturing cycle. The optomechanical design and manufacturing of the Alvarez lens arrays and mounting parts are presented in detail. The optical performance of the system is evaluated and compared with simulation results using a custom camera-based test station. Experimental results demonstrate and confirm the dynamic illumination concept with good uniformity.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1117/12.2320574
