An official website of the United States government
Additively manufactured electronics (AMEs), also known as printed electronics, are becoming increasingly important for the anticipated Internet of Things (IoT). This requires manufacturing technologies that allow the integration of various pure functional materials and devices onto different flexible and rigid surfaces. However, the current ink-based technologies suffer from complex and expensive ink formulation, ink-associated contaminations (additives/solvents), and limited sources of printing materials. Thus, printing contamination-free and multimaterial structures and devices is challenging. Here, a multimaterial additive nanomanufacturing (M-ANM) technique utilizing directed laser deposition at the nano and microscale is demonstrated, allowing the printing of lateral and vertical hybrid structures and devices. This M-ANM technique involves pulsed laser ablation of solid targets placed on a target carousel inside the printer head for in-situ generation of contamination-free nanoparticles, which are then guided via a carrier gas toward the nozzle and onto the surface of the substrate, where they are sintered and printed in real-time by a second laser. The target carousel brings a particular target in engagement with the ablation laser beam in predetermined sequences to print multiple materials, including metals, semiconductors, and insulators, in a single process. Using this M-ANM technique, various multimaterial devices such as silver/zinc oxide (Ag/ZnO) photodetector and hybrid silver/aluminum oxide (Ag/Al2O3) circuits are printed and characterized. The quality and versatility of our M-ANM technique offer a potential manufacturing option for emerging IoT.
more »
« less
Nozzle‐Free Printing of CNT Electronics Using Laser‐Generated Focused Ultrasound
Abstract Printed electronics have made remarkable progress in recent years and inkjet printing (IJP) has emerged as one of the leading methods for fabricating printed electronic devices. However, challenges such as nozzle clogging, and strict ink formulation constraints have limited their widespread use. To address this issue, a novel nozzle‐free printing technology is explored, which is enabled by laser‐generated focused ultrasound, as a potential alternative printing modality called Shock‐wave Jet Printing (SJP). Specifically, the performance of SJP‐printed and IJP‐printed bottom‐gated carbon nanotube (CNT) thin film transistors (TFTs) is compared. While IJP required ten print passes to achieve fully functional devices with channel dimensions ranging from tens to hundreds of micrometers, SJP achieved comparable performance with just a single pass. For optimized devices, SJP demonstrated six times higher maximum mobility than IJP‐printed devices. Furthermore, the advantages of nozzle‐free printing are evident, as SJP successfully printed stored and unsonicated inks, delivering moderate electrical performance, whereas IJP suffered from nozzle clogging due to CNT agglomeration. Moreover, SJP can print significantly longer CNTs, spanning the entire range of tube lengths of commercially available CNT ink. The findings from this study contribute to the advancement of nanomaterial printing, ink formulation, and the development of cost‐effective printable electronics.
more »
« less
- Award ID(s):
- 1825502
- PAR ID:
- 10505273
- Publisher / Repository:
- Wiley-VCH GmbH
- Date Published:
- Journal Name:
- Small Methods
- ISSN:
- 2366-9608
- Subject(s) / Keyword(s):
- Printed Electronics Nozzle-Free Additive Manufacturing
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Electrohydrodynamic (EHD) printing has become a promising and cost-effective technique for producing high-resolution and large-scale features. One widely recognized obstacle in EHD printing is nozzle clogging due to solvent evaporation or ink polymerization. Moreover, printing highly viscous materials often requires pressure or other external force to assist the ink flow during the printing, which increases the complexity of process control and the required energy. In this work, we developed a novel ultrasonic vibration-assisted EHD printhead and associated process to effectively eliminate the nozzle clogging for the printing of high-viscosity and high-evaporation-rate inks. A series of experimental tests were conducted to characterize the printhead design and process parameters (i.e., vibration frequency, vibration amplitude, and printing voltage). The results demonstrated that superimposing ultrasonic vibration on the EHD printing nozzle can effectively enhance current EHD printing capabilities, such as reducing required pressure, eliminating nozzle clogging, and providing stable and continuous printing for high viscosity and high solvent evaporation rate material. With the optimal parameters, a filament with a diameter of around 1 µm can be continuously printed. In the paper, we successfully applied this developed ultrasonic-assisted EHD process to print high-resolution 2D patterns.more » « less
-
Abstract Inkjet printing of electronic materials is of interest for digital printing of flexible electronics and sensors, but the width of the inkjet-printed lines is still large, limiting device size and performance. Decreasing the drop volume, increasing the drop spacing, and increasing the ink-substrate contact angle are all approaches by which the line width can be lowered, however these approaches are limited by the nozzle geometry, ink coalescence and bead instabilities, and contact angle hysteresis, respectively. Here we demonstrate a novel approach for stable inkjet printing of very narrow lines on ink-substrate combinations with a high contact angle, utilizing the de-wetting of the ink due to the decreased contact angle hysteresis. After printing and drying an initial layer of disconnected seed drops of silver nanoparticle ink, we print an additional layer of bridging drops of the same ink in between the dried seed drops. The bridging drops expand to touch the dried seed drops and then retract into a line, due to the pinning of the wet ink on the dried seed ink but not on the substrate, forming a continuous silver trace. The trace width is decreased from 60μm with a traditional printing approach down to 12.6μm with this seed-bridge approach. The electrical conductivity of the silver trace is similar to that of a conventionally printed trace. Due to poor adhesion on the print substrate, the trace was transferred to a separate polymer substrate with a simple hot-pressing procedure, which preserves the electrical conductivity of the trace.more » « less
-
Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human‐machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.more » « less
-
Birringer, Marc (Ed.)Abstract Over the past several years, atomically thin two‐dimensional carbides, nitrides, and carbonitrides, otherwise known asMXenes, have been expanded into over fifty material candidates that are experimentally produced, and over one hundred fifty more candidates that have been theoretically predicted. They have demonstrated transformative properties such as metallic‐type electrical conductivities, optical properties such as plasmonics and optical nonlinearity, and key surface properties such as hydrophilicity, and unique surface chemistry. In terms of their applications, they are poised to transform technological areas such as energy storage, electromagnetic shielding, electronics, photonics, optoelectronics, sensing, and bioelectronics. One of the most promising aspects ofMXene'sfuture application in all the above areas of interest, we believe, is reliably developing their flexible and bendable electronics and optoelectronics by printing methods (henceforth, termed asprinted flexible MXetronics). Designing and manipulatingMXeneconductive inks according to the application requirements will therefore be a transformative goal for future printed flexible MXetronics.MXene'scombined property of high electrical conductivity and water‐friendly nature to easily disperse its micro/nano‐flakes in an aqueous medium without any binder paves the way for designing additive‐free highly conductiveMXene ink. However, the chemical and/or structural and hence functional stability of water basedMXeneinks over time is not reliable, opening research avenues for further development of stable and conductiveMXeneinks. Such priorities will enable applications requiring high‐resolution and highly reliable printedMXeneelectronics using state‐of‐the art printing methods. EngineeringMXenestructural and surface functional properties while tuningMXeneink rheology in benign solvents of choice will be a key for ink developments. This review article summarizes the present status and prospects ofMXeneinks and their use in inkjet‐printed (IJP) technology for future flexible and bendableMXetronics.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1002/smtd.202301596
