skip to main content


This content will become publicly available on May 1, 2025

Title: A broadband pulse amplifier for Joule heating experiments in diamond anvil cells
Decades of measurements of the thermophysical properties of hot metals show that pulsed Joule heating is an effective method to heat solid and liquid metals that are chemically reactive or difficult to contain. To extend such measurements to hundreds of GPa pressure, pulsed heating methods have recently been integrated with diamond anvil cells. The recent design used a low-side switch and active electrical sensing equipment that was prone to damage and measurement error. Here, we report the design and characterization of new electronics that use a high-side switch and robust, passive electrical sensing equipment. The new pulse amplifier can heat ∼5 to 50 μm diameter metal wires to thousands of kelvin at tens to hundreds of GPa using diamond anvil cells. Pulse durations and peak currents can each be varied over three orders of magnitude, from 5 µs to 10 ms and from 0.2 to 200 A. The pulse amplifier is integrated with a current probe. Two voltage probes attached to the body of a diamond anvil cell are used to measure voltage in a four-point probe geometry. The accuracy of four-point probe resistance measurements for a dummy sample with 0.1 Ω resistance is typically better than 5% at all times from 2 µs to 10 ms after the beginning of the pulse.  more » « less
Award ID(s):
2125954
NSF-PAR ID:
10506898
Author(s) / Creator(s):
; ;
Publisher / Repository:
AIP
Date Published:
Journal Name:
Review of Scientific Instruments
Volume:
95
Issue:
5
ISSN:
0034-6748
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. When diamond anvil cell (DAC) sample chambers are outfitted with both thermal insulation and electrodes, two cutting-edge experimental methods are enabled: Joule heating with spectroradiometric temperature measurement and electrical resistance measurements of samples heated to thousands of kelvin. The accuracy of temperature and resistance measurements, however, often suffers from poor control of the shape and location of the sample, electrodes, and thermal insulation. Here, we present a recipe for the reproducible and precise fabrication of DAC sample, electrodes, and thermal insulation using a three-layer microassembly. The microassembly contains two potassium chloride thermal insulation layers, four electrical leads, a sample, and a buttressing layer made of polycrystalline alumina. The sample, innermost electrodes, and buttress layer are fabricated by focused-ion-beam milling. Three iron samples are presented as proof of concept. Each is successfully compressed and pulsed Joule heated while maintaining a four-point probe configuration. The highest pressure-temperature condition achieved is ∼150 GPa and 4000 K.

     
    more » « less
  2. Accurate and precise measurements of spectroradiometric temperature are crucial for many high pressure experiments that use diamond anvil cells or shock waves. In experiments with sub-millisecond timescales, specialized detectors such as streak cameras or photomultiplier tubes are required to measure temperature. High accuracy and precision are difficult to attain, especially at temperatures below 3000 K. Here, we present a new spectroradiometry system based on multianode photomultiplier tube technology and passive readout circuitry that yields a 0.24 µs rise-time for each channel. Temperature is measured using five color spectroradiometry. During high pressure pulsed Joule heating experiments in a diamond anvil cell, we document measurement precision to be ±30 K at temperatures as low as 2000 K during single-shot heating experiments with 0.6 µs time-resolution. Ambient pressure melting tests using pulsed Joule heating indicate that the accuracy is ±80 K in the temperature range 1800–2700 K. 
    more » « less
  3. Goethite is a major iron-bearing sedimentary mineral on Earth. In this study, we conducted in situ high-pressure x-ray diffraction, Raman, and electrical impedance spectroscopy measurements of goethite using a diamond anvil cell (DAC) at room temperature and high pressures up to 32 GPa. We observed feature changes in both the Raman spectra and electrical resistance at about 5 and 11 GPa. However, the x-ray diffraction patterns show no structural phase transition in the entire pressure range of the study. The derived pressure-volume (P-V) data show a smooth compression curve with no clear evidence of any second-order phase transition. Fitting the volumetric data to the second-order Birch–Murnaghan equation of state yields V0 = 138.9 ± 0.5 Å3 and K0 = 126 ± 5 GPa. 
    more » « less
  4. Abstract

    Cryopreservation by vitrification has far-reaching implications. However, rewarming techniques that are rapid and scalable (both in throughput and biosystem size) for low concentrations of cryoprotective agent (CPA) for reduced toxicity are lacking, limiting the potential for translation. Here, we introduce a joule heating–based platform technology, whereby biosystems are rapidly rewarmed by contact with an electrical conductor that is fed a voltage pulse. We demonstrate successful cryopreservation of three model biosystems with thicknesses across three orders of magnitude, including adherent cells (~4 µm),Drosophila melanogasterembryos (~50 µm) and rat kidney slices (~1.2 mm) using low CPA concentrations (2–4 M). Using tunable voltage pulse widths from 10 µs to 100 ms, numerical simulation predicts that warming rates from 5 × 104to 6 × 108 °C/min can be achieved. Altogether, our results present a general solution to the cryopreservation of a broad spectrum of cellular, organismal and tissue-based biosystems.

     
    more » « less
  5. In this paper, we propose and demonstrate electrical switching of a 4% tungsten-doped Ge2Sb2Te5(W-GST) pixel in a lateral configuration without the need for an auxiliary resistive heater. The phase transition between an amorphous and poly-crystalline state is achieved by Joule heating directly through the 4μm × 4μm × 350 nm active volume of the chalcogenide phase change pixel. While undoped GST would be challenging to switch in a lateral configuration due to very large resistance in the amorphous state, W-GST allows for switching at reasonable voltage levels. The pixel temperature profile is simulated using finite element analysis methods to identify the pulse parameters required for a successful electrical actuation. Experimentally, a 1550 nm light source is used for in-situ optical reflection measurements in order to verify the crystallization and re-amorphization of the pixel. As a result of the W doping, we identify volatile and non-volatile regimes with respect to bias voltage and pulse width during crystallization. During amorphization, we observe irreversible material failure after one complete cycle using in-situ optical monitoring, which can be attributed to a migration or segregation process. These results provide a promising path toward electrically addressed devices that are suitable for optical applications requiring amplitude modulation in a reflective geometry, such as spatial light modulators.

     
    more » « less