An official website of the United States government
This paper details the development and analysis of a computational neuroscience model, known as a Synthetic Nervous System, for the control of a simulated worm robot. Using a Synthetic Nervous System controller allows for adaptability of the network with minimal changes to the system. The worm robot kinematics are inspired by earthworm peristalsis which relies on the hydrostatic properties of the worm’s body to produce soft-bodied locomotion. In this paper the hydrostatic worm body is approximated as a chain of two dimensional rhombus shaped segments. Each segment has rigid side lengths, joints at the vertices, and a linear actuator to control the segment geometry. The control network is composed of non-spiking neuron and synapse models. It utilizes central pattern generators, coupled via interneurons and sensory feedback, to coordinate segment contractions and produce a peristaltic waveform that propagates down the body of the robot. A direct perturbation Floquet multiplier analysis was performed to analyze the stability of the peristaltic wave’s limit cycle.
more »
« less
A Dynamic Simulation of a Compliant Worm Robot Amenable to Neural Control
This paper details the development and validation of a dynamic 3D compliant worm-like robot model controlled by a Synthetic Nervous System (SNS). The model was built and simulated in the physics engine Mujoco which is able to approximate soft bodied dynamics and generate contact, gravitational, frictional, and internal forces. These capabilities allow the model to realistically simulate the movements and dynamic behavior of a physical soft-bodied worm-robot. For validation, the results of this simulation were compared to data gathered from a physical worm robot and found to closely match key behaviors such as deformation propagation along the compliant structure and actuator efficiency losses in the middle segments. The SNS controller was previously developed for a simple 2D kinematic model and has been successfully implemented on this 3D model with little alteration. It uses coupled oscillators to generate coordinated actuator control signals and induce peristaltic locomotion. This model will be useful for analyzing dynamic effects during peristaltic locomotion like contact forces and slip as well as developing and improving control algorithms that avoid unwanted slip.
more »
« less
- Award ID(s):
- 2015317
- PAR ID:
- 10517577
- Publisher / Repository:
- Springer, Cham.
- Date Published:
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Soft robotic snakes made of compliant materials can continuously deform their bodies and, therefore, mimic the biological snakes' flexible and agile locomotion gaits better than their rigid-bodied counterparts. Without wheel support, to date, soft robotic snakes are limited to emulating planar locomotion gaits, which are derived via kinematic modeling and tested on robotic prototypes. Given that the snake locomotion results from the reaction forces due to the distributed contact between their skin and the ground, it is essential to investigate the locomotion gaits through efficient dynamic models capable of accommodating distributed contact forces. We present a complete spatial dynamic model that utilizes a floating-base kinematic model with distributed contact dynamics for a pneumatically powered soft robotic snake. We numerically evaluate the feasibility of the planar and spatial rolling gaits utilizing the proposed model and experimentally validate the corresponding locomotion gait trajectories on a soft robotic snake prototype. We qualitatively and quantitatively compare the numerical and experimental results which confirm the validity of the proposed dynamic model.more » « less
-
Abstract Soft earthworm‐like robots that exhibit mechanical compliance can, in principle, navigate through uneven terrains and constricted spaces that are inaccessible to traditional legged and wheeled robots. However, unlike the biological originals that they mimic, most of the worm‐like robots reported to date contain rigid components that limit their compliance, such as electromotors or pressure‐driven actuation systems. Here, a mechanically compliant worm‐like robot with a fully modular body that is based on soft polymers is reported. The robot is composed of strategically assembled, electrothermally activated polymer bilayer actuators, which are based on a semicrystalline polyurethane with an exceptionally large nonlinear thermal expansion coefficient. The segments are designed on the basis of a modified Timoshenko model, and finite element analysis simulation is used to describe their performance. Upon electrical activation of the segments with basic waveform patterns, the robot can move through repeatable peristaltic locomotion on exceptionally slippery or sticky surfaces and it can be oriented in any direction. The soft body enables the robot to wriggle through openings and tunnels that are much smaller than its cross‐section.more » « less
-
Due to their compliant mechanics, many soft and flexible robots are well-suited to operate in confined spaces that challenge traditional legged and wheeled robots. In particular, undulatory and peristaltic robots excel in enclosed tunnels and pipes, as their locomotion methods and compliance allow them to wriggle and squeeze through narrowings and gaps. However, these environments frequently contain features that are impassable with passive deformation alone, such as sharp turns and T-junctions. In this work, we developed the first closed-loop, peristaltic turning algorithm that scales turning angle based on contact force feedback in confined spaces. We verified the controller’s effectiveness using a dynamic model of a soft worm robot as our test platform. The model was sent through pipe bends with varying radii of curvature, diameters, and geometries, using both open-loop and closed-loop controllers. The different turning strategies were compared using speed and the cost of transport (COT) as the primary metrics. Our adaptive algorithm was the only turning method which maintained high speed performance across all bends tested. The model averaged just a 1.6% loss in speed compared to the best fixed turning angle strategy for each pipe curvature. Adaptive turning also allowed the model to traverse small radius of curvature (ROC) bends (0.5 and 0.6 m) in which the model became stuck when using straightline locomotion. Furthermore, of the controllers we tested, adaptive turning offered the lowest COT in most pipe bend geometries. We also showed that the controller could autonomously transition from left to right turns (and vice versa) and adjust to a spiral turn with a continuously changing ROC. A worm robot with this controller, these sensors, and turning capabilities would be well equipped for operation in a wide variety of unstructured and confined environments.more » « less
-
Soft robots employ flexible and compliant materials to perform adaptive tasks and navigate uncertain environments. However, soft robots are often unable to achieve forces and precision on the order of rigid-bodied robots. In this paper, we propose a new class of mobile soft robots that can reversibly transition between compliant and stiff states without reconfiguration. The robot can passively conform or actively control its shape, stiffen in its current configuration to function as a rigid-bodied robot, then return to its flexible form. The robotic structure consists of passive granular material surrounded by an active membrane. The membrane is composed of interconnected robotic sub-units that can control the packing density of the granular material and exploit jamming behaviors by varying the length of the interconnecting cables. Each robotic sub-unit uses a differential drive system to achieve locomotion and self-reconfigurability. We present the robot design and perform a set of locomotion and object manipulation experiments to characterize the robot's performance in soft and rigid states. We also introduce a simulation framework in which we model the jamming soft robot design and study the scalability of this class of robots. The proposed concept demonstrates the properties of both soft and rigid robots, and has the potential to bridge the gap between the twomore » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Conference Paper:
- https://doi.org/10.1007/978-3-031-38857-6_25
